Thank you so much Marco! I have saved your message. Michael advised me something similar with the ending -vvvvv gl nn
On Mon, Dec 21, 2020 at 3:08 PM Marco Calistri <py1...@outlook.com> wrote: > Andras, > > You can dig into get more details/information *out of WSJT-X* to verify > your hamlib and your interfaces settings/responses from your > console/command prompt: > > /usr/bin/rigctld -m 1021(¹) -r /dev/FT-100_USB1(²) -p /dev/FT-100_USB0(³) > -t 4532 -s 4800 -vvvvv > > (¹) = The model of your radio, *for you is 1027*! > > (²)=The serial interface you use for CAT interface > > (³)= The serial interface you use for your PTT (if any) > > *More details: /usr/bin/rigctld -h* > > marco@linux-turion64:~> rigctld -h > > Usage: rigctld [OPTION]... > > Daemon serving COMMANDs to a connected radio transceiver or receiver. > > -m, --model=ID select radio model number. See model list > > -r, --rig-file=DEVICE set device of the radio to operate on > > -p, --ptt-file=DEVICE set device of the PTT device to operate on > > -d, --dcd-file=DEVICE set device of the DCD device to operate on > > -P, --ptt-type=TYPE set type of the PTT device to operate on > > -D, --dcd-type=TYPE set type of the DCD device to operate on > > -s, --serial-speed=BAUD set serial speed of the serial port > > -c, --civaddr=ID set CI-V address, decimal (for Icom rigs only) > > -t, --port=NUM set TCP listening port, default 4532 > > -T, --listen-addr=IPADDR set listening IP address, default ANY > > -C, --set-conf=PARM=VAL set config parameters > > -L, --show-conf list all config parameters > > -l, --list list all model numbers and exit > > -u, --dump-caps dump capabilities and exit > > -o, --vfo do not default to VFO_CURR, require extra vfo > arg > > -v, --verbose set verbose mode, cumulative (-v to -vvvvv) > > -W, --twiddle_timeout timeout after detecting vfo manual change > > -x, --uplink set uplink get_freq ignore, 1=Sub, 2=Main > > -Z, --debug-time-stamps enable time stamps for debug messages > > -h, --help display this help and exit > > -V, --version output version information and exit > > Commands (some may not be available for this rig): > > F: set_freq (Frequency) f: get_freq () > > M: set_mode (Mode,Passband) m: get_mode () > > I: set_split_freq (TX Frequency) i: get_split_freq () > > X: set_split_mode (TX Mode,TX Passband) x: get_split_mode () > > K: set_split_freq_mode(TX Frequency,TX Mode,TX Passband) k: > get_split_freq_mode() > > S: set_split_vfo (Split,TX VFO) s: get_split_vfo () > > N: set_ts (Tuning Step) n: get_ts () > > L: set_level (Level,Level Value) l: get_level (Level) > > U: set_func (Func,Func Status) u: get_func (Func) > > P: set_parm (Parm,Parm Value) p: get_parm (Parm) > > G: vfo_op (Mem/VFO Op) g: scan (Scan Fct,Scan > Channel) > > A: set_trn (Transceive) a: get_trn () > > R: set_rptr_shift (Rptr Shift) r: get_rptr_shift () > > O: set_rptr_offs (Rptr Offset) o: get_rptr_offs () > > C: set_ctcss_tone (CTCSS Tone) c: get_ctcss_tone () > > D: set_dcs_code (DCS Code) d: get_dcs_code () > > ?: set_ctcss_sql (CTCSS Sql) ?: get_ctcss_sql () > > ?: set_dcs_sql (DCS Sql) ?: get_dcs_sql () > > V: set_vfo (VFO) v: get_vfo () > > T: set_ptt (PTT) t: get_ptt () > > E: set_mem (Memory#) e: get_mem () > > H: set_channel (Channel) h: get_channel (Channel,Read Only) > > B: set_bank (Bank) _: get_info () > > J: set_rit (RIT) j: get_rit () > > Z: set_xit (XIT) z: get_xit () > > Y: set_ant (Antenna,Option) y: get_ant (AntCurr) > > ?: set_powerstat (Power Status) ?: get_powerstat () > > ?: send_dtmf (Digits) ?: recv_dtmf () > > *: reset (Reset) w: send_cmd (Cmd) > > W: send_cmd_rx (Cmd,Reply) b: send_morse (Morse) > > ?: stop_morse () ?: wait_morse () > > ?: send_voice_mem (Voice Mem#) ?: get_dcd () > > ?: set_twiddle (Timeout (secs)) ?: get_twiddle () > > ?: uplink (1=Sub, 2=Main) ?: set_cache (Timeout (msecs)) > > ?: get_cache () 2: power2mW (Power > [0.0..1.0],Frequency,Mode) > > 4: mW2power (Pwr mW,Freq,Mode) 1: dump_caps () > > 3: dump_conf () ?: dump_state () > > ?: chk_vfo () ?: set_vfo_opt (Status) > > ?: halt () ?: pause (Seconds) > > In interactive mode prefix long command names with '\', e.g. '\dump_state' > > The special command '-' is used to read further commands from standard input > > Commands and arguments read from standard input must be white space separated, > > comments are allowed, comments start with the # character and continue to the > > end of the line. > > Report bugs to <hamlib-develo...@lists.sourceforge.net> > <hamlib-develo...@lists.sourceforge.net>. > > > Regards, > > > > *--- 73 de Marco, PY1ZRJ (former IK5BCU) * > > > Il 21/12/20 10:32, Andras Bato ha scritto: > > Bill, > I have switched back to CW now. > Let me wait for WSJT-X 2.3.0 > Then, I am going to investigate the problem again. > Have a nice Christmas! > Andras HA6NN > > On Mon, Dec 21, 2020 at 1:41 PM Bill Somerville <g4...@classdesign.com> > wrote: > >> Andras, >> >> I do not see any record of a rig control issues reported by you on this >> list. Perhaps you can share the details so a resolution can be found? >> >> 73 >> Bill >> G4WJS. >> >> On 21/12/2020 09:34, Andras Bato wrote: >> >> Thank you so much, Mike. >> I haven't got any written details about the possible difference so far. >> The hard truth was when MSHV was working nicely with my FT450D >> and WSJT-x reported rig failure. >> Andras HA6NN >> >> >> On Sun, Dec 20, 2020 at 11:47 PM Black Michael via wsjt-devel < >> wsjt-devel@lists.sourceforge.net> wrote: >> >>> There's no practical difference between the 450 and 450D >>> The 450D is recognized to be the same as the 450. >>> >>> I'll contact you off-line about debugging the problem. >>> >>> Mike W9MDB >>> >> >> _______________________________________________ >> wsjt-devel mailing list >> wsjt-devel@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/wsjt-devel >> > > > _______________________________________________ > wsjt-devel mailing > listwsjt-devel@lists.sourceforge.nethttps://lists.sourceforge.net/lists/listinfo/wsjt-devel > > > > _______________________________________________ > wsjt-devel mailing list > wsjt-devel@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/wsjt-devel >
_______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/wsjt-devel
