Hi Dirk,
so I can see what is happening please put the attached file into your
WSJT-X configuration files directory (on MS Windows that is the the same
as the log files directory - "Menu->File->Open log directory"), then
quit and restart WSJT-X. Do a minimum test that demonstrate the issue,
then quit WSJT-X. You will have a new file on your Desktop called
WSJT-X_RigControl.log , send that file to me (g4wjs <at> classdesign
<dot> com) for analysis please?
Once you have sent the log file you can delete it and the
wsjtx_log_config.ini files to revert WSJT-X to normal diagnostic logging.
73
Bill
G4WJS.
On 18/02/2021 13:08, Dirk Kuschke via wsjt-devel wrote:
Hello Bill,
no, I use only VFO A never VFO B
73, Dirk
DD5KD
Am Donnerstag, 18. Februar 2021, 13:44:06 MEZ hat Bill Somerville
<g4...@classdesign.com> Folgendes geschrieben:
Hi Dirk,
are you trying to run WSJT-X with reception from VFO B?
73
Bill
G4WJS.
On 17/02/2021 18:57, Dirk Kuschke via wsjt-devel wrote:
I had thought that too, but it is not the reasen, if I switched off
the split before, I get split again when switching over. Iswitched
all bands through with the software and switched split off, the next
test, split was there again. That's only since version 2.3.0 with
2.2.2 everything is as it should be.I switched all
bands on the TRX there is no split, only when it is switched via wsjtx.
73, de Dirk
DD5KD
Am Mittwoch, 17. Februar 2021, 16:29:20 MEZ hat Bill Somerville
<g4...@classdesign.com> <mailto:g4...@classdesign.com> Folgendes
geschrieben:
On 17/02/2021 15:03, Dirk Kuschke via wsjt-devel wrote:
Hello,
since FTDX version 2.3.0
my yaesu ftdx3000d changes to split mode when I change the frequency,
using the button on the left. Up to version WSJTX2.2.2 this was not
the case.
The settings are:
Inline-Bild Inline-Bild
I change the Databits between 7 or 8 and the Stop bits between 1 or
2 with
no effect. The correct setting Databit 8 and 2 Stop bits lt. Yaesu UK.
In the settings i also change the radio to Yaesu FT-950 with the same
affect change to split mode….
73, Dirk
Hi Dirk,
if this is happening when you change bands then it is because SPLIT
was set the last time that band was used on the rig. If you disable
SPLIT it should be fine the next time you change to that band. The
same applies for other bands. The change in behaviour is that WSJT-X,
via Hamlib, is changing bands on your rig as if you have clicked the
target band button before changing to the target frequency in that
band. The reason for the change is that other settings are also
recalled per band like the aerial socket, pre-amp settings, etc..
73
Bill
G4WJS.
[Sinks.SYSLOG]
Destination=TextFile
Asynchronous=true
AutoFlush=false
FileName="${AppLocalDataLocation}/wsjtx_syslog.log"
TargetFileName="${AppLocalDataLocation}/logs/wsjtx_syslog_%Y-%m.log"
RotationTimePoint="01 00:00:00"
Append=true
EnableFinalRotation=false
MaxSize=41943040
MinFreeSpace=1073741824
MaxFiles=12
Target="${AppLocalDataLocation}/logs"
ScanForFiles="Matching"
Format="[%Channel%][%TimeStamp(format=\"%Y-%m-%d
%H:%M:%S.%f\")%][%Uptime(format=\"%O:%M:%S.%f\")%][%Severity%] %Message%"
Filter="%Severity% >= info"
[Sinks.RIGCTRL]
Destination=TextFile
Asynchronous=true
AutoFlush=true
FileName="${DesktopLocation}/WSJT-X_RigControl.log"
Append=true
Format="[%TimeStamp(format=\"%Y-%m-%d
%H:%M:%S.%f\")%][%Uptime(format=\"%O:%M:%S.%f\")%][%Channel%:%Severity%]
%Message%"
Filter="%Channel% matches \"RIGCTRL\" | %Severity% >= info"
_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
