> De: "Gilles Chanteperdrix" <[email protected]>
> À: "aubin rebillat" <[email protected]>
> Cc: [email protected]
> Envoyé: Jeudi 10 Mai 2012 18:34:38
> Objet: Re: [Xenomai-help] Xenomai on the TS-7553 ARM SBC
>
> On 05/10/2012 06:04 PM, [email protected] wrote:
> > I'm not that experienced with initrd/initramfs and that was what
> > the
> > manufacturer recommended and i followed it so i can have support
> > from
> > them. But yes, at first, i think it can boot from another device.
>
> Could you wrap your lines around 72 characters ? I have to do it for
> you
> when I want to reply your posts.
I will, sorry for the inconvenience.
>
> >
> >>
> >>> I will look into the OABI and EABI settings then. I will also set
> >>> up
> >>> an NFS file system to mount debian from and see what is
> >>> happening.
> >>>
> >>> Thank you Gilles for your reply. I will keep posting about my
> >>> progresses.
> >>
> >> The issue may simply well be that your timer code does not work.
> >> Could
> >> you post the code for your port? That is, the code you added to
> >> get
> >> it
> >> work with the I-pipe patch.
> >> Have you checked that linux timer is
> >> still
> >> ticking after Xenomai has been started?
> >
> > No, i did not check that the linux timer is still ticking.
> > But i think it is because parts of the init script are executed and
> > it is a shell script calling several sub-processes.
>
> If subprocesses were an issue, nobody would be able to run xenomai.
>
>
> > Nevertheless, I will put some printk in the linux timer handler to
> > be sure.
> >
> >>
> >> You can also try to boot with CONFIG_IPIPE but without
> >> CONFIG_XENOMAI.
> >
> > I did, and it's booting just fine.
>
> Ok. Then it is really likely the timer code which is broken. As the
> only
> difference when xenomai is started is that linux timer is handled by
> xenomai.
>
>
> > void ipipe_mach_update_tsc(void)
> > {
> > union tsc_reg *local_tsc;
> > unsigned long stamp;
> > unsigned long flags;
> >
> > local_irq_save_hw(flags);
> > local_tsc = &tsc[ipipe_processor_id()];
> > stamp = str8100_read_timer_counter();
> > if (stamp < local_tsc->low)
> > local_tsc->high++;
> > local_tsc->low = stamp;
> > local_irq_restore_hw(flags);
> > }
>
> Since this code is called from the timer ack routine, the interrupts
> are
> already off, so, you should not need local_irq_save_hw. On the other
> hand, calling ipipe_mach_update_tsc in the timer ack routine adds to
> the
> timer interrupt latency, so, should be done only if the time source
> is
> wrapping really fast. As your timesource is a 32 bits timesource
> (according to what you wrote in __ipipe_mach_get_tscinfo), it is
> probably not wrapping fast, and you can call ipipe_mach_update_tsc
> from
> linux timer interrupt.
>
> >
> > void __ipipe_mach_acktimer(void)
> > {
> > #ifndef CONFIG_VIC_INTERRUPT
> > write_seqlock(&xtime_lock);
> > str8100_clear_timer_interrupt_status(__ipipe_mach_timerint);
> > write_sequnlock(&xtime_lock);
> > #endif
> >
> > ipipe_mach_update_tsc();
> > }
>
> Wrong: you can not call write_seqlock from the acktimer routine. The
> seqlock are reserved to usage by Linux. Also note that you should
> remove
> the call to str8100_clear_timer_interrupt_status from Linux timer
> interrupt.
Actually, it's only if the Vector Interrupt Controller from the CNS2132
is not enabled, which is not my case. But at least i should erase this.
>
>
> > void __ipipe_mach_set_dec(unsigned long delay)
> > {
> > unsigned long flags;
> >
> > if (delay > 8)
> > {
> > local_irq_save_hw(flags);
> > TIMER1_MATCH_VALUE1_REG = TIMER1_COUNTER_REG + delay;
> > local_irq_restore_hw(flags);
> > }
> > else
> > ipipe_trigger_irq(__ipipe_mach_timerint);
> > }
>
> ipipe_mach_set_dec is called with interrupts already off, so there is
> no
> need to call local_irq_save_hw/local_irq_restore_hw.
>
> Also, from the sources I could gather (snakeos-sdk), the hardware
> timer
> for str8100 is programmed in periodic, auto-reload mode. Obviously,
> when
> CONFIG_IPIPE is on, you have to change this to make the timer run in
> one-shot mode, as required by Xenomai.
I did not know that it was required, i thought it was handy not to reprogram
the timer each time.
>
> > #ifdef CONFIG_IPIPE
> > void __ipipe_mach_demux_irq(unsigned irq, struct pt_regs *regs)
> > {
> > // No cascaded interrupt using the VIC
> > }
> > #endif /* CONFIG_IPIPE */
>
> You probably do not need to define this function if you #define
> ipipe_mach_irq_mux_p to always be 0.
>
I do, to avoid an undefined reference.
Nevertheless, thank you very much for all this.
When i developped the IPIPE code for this board i followed the
HOWTO but it's quite vague so I mostly read what has been done
with other boards and what has been done with linux for this board
to implement it.
Therefore, I'm clearly not aware of the interactions between Linux
and Xenomai. I will definitely read the publications available on
the Xenomai website.
Best regards,
--
REBILLAT Aubin
_______________________________________________
Xenomai-help mailing list
[email protected]
https://mail.gna.org/listinfo/xenomai-help
