Hello, Unfortunately I have no knowledge about that how image is built :( I got just that image downloaded which is already built.
BUT after applying ifconfig I got network working and connection established... Now I wanna do it permanetly and dhcp instead of static IP. root@imx6qpsabreauto:~# ifconfig eth0 10.171.88.8 netmask 255.0.0.0 up root@imx6qpsabreauto:~# ifconfig eth0 Link encap:Ethernet HWaddr ee:d2:50:0d:f3:33 inet addr:10.171.88.8 Bcast:10.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::ecd2:50ff:fe0d:f333/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4447 errors:0 dropped:951 overruns:0 frame:0 TX packets:254 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:640741 (625.7 KiB) TX bytes:37067 (36.1 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2000 errors:0 dropped:0 overruns:0 frame:0 TX packets:2000 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:152000 (148.4 KiB) TX bytes:152000 (148.4 KiB) root@imx6qpsabreauto:~# within /etc/network directory root@imx6qpsabreauto:/etc/network# ls if-down.d if-post-down.d if-pre-up.d if-up.d interfaces root@imx6qpsabreauto:/etc/network# vi interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp ~ ~ ~ After reset I need to set network again and static ... cheers, Peter On Fri, May 12, 2017 at 9:55 PM, Trevor Woerner <twoer...@gmail.com> wrote: > Hi Peter, > > There isn't enough information here for me to help you. > > Could you please list the commands and steps you used to build the image? > - what repositories are you using? > - what branches of those repositories? > - if you changed any config files, what did you change? > - what command did you run to build your image? > - what did bitbake print as your build configuration? > > Which i.mx board are you using? There are dozens of them. > > Best regards, > Trevor > > > On Fri, May 12, 2017 at 3:34 PM, pe...@gmail.com > <balazovic.pe...@gmail.com> wrote: > > I build on i.mx (NXP) machine, I want to get configured as dhcp (no > > static)... > > > > > > ------ Original Message ------ > > From: "Trevor Woerner" <twoer...@gmail.com> > > To: "Peter Balazovic" <balazovic.pe...@gmail.com> > > Cc: "Yocto list discussion" <yocto@yoctoproject.org> > > Sent: 5/12/2017 9:32:17 PM > > Subject: Re: [yocto] dhcp eth0 network > > > >> Hi Peter, > >> > >> For what MACHINE are you building? What's your target hardware? Can > >> you summarize the steps you took to build your image? > >> > >> What do you want eth0 to do? dhcp or static ip? > >> > >> Best regards, > >> Trevor > >> > >> > >> On Fri, May 12, 2017 at 12:01 PM, Peter Balazovic > >> <balazovic.pe...@gmail.com> wrote: > >>> > >>> Dears, > >>> > >>> I got Yocto image and unfortunatelly network is not somehow enabled & > >>> proprely configured. After "ifconfig" no eth0 configured. > >>> > >>> > >>>> ifconfig > >>> > >>> lo Link encap:Local Loopback > >>> inet addr:127.0.0.1 Mask:255.0.0.0 > >>> .... > >>> > >>> > >>> > >>>> /etc/network > >>>> ls > >>> > >>> if-down.d if-post-down.d if-pre-up.d if-up.d > >>> > >>> > >>> How should I setup "eth0" to get network working properly? > >>> > >>> Thanks. > >>> > >>> > >>> > >>> -- > >>> _______________________________________________ > >>> yocto mailing list > >>> yocto@yoctoproject.org > >>> https://lists.yoctoproject.org/listinfo/yocto > >>> > > >
-- _______________________________________________ yocto mailing list yocto@yoctoproject.org https://lists.yoctoproject.org/listinfo/yocto