Yes if you put it in recovery mode it's only the cat5 cable (default OOB config).
Josh Luthman 24/7 Help Desk: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Thu, Apr 22, 2021 at 12:37 PM Nate Burke <n...@blastcomm.com> wrote: > Ok, that makes me feel a little better > > Recovery mode appears to be available on both the Fiber and Cat5 From > there you can enter 'default mode' which will set the data path to the > Cat5, and you can update and reboot from there. > > On 4/22/2021 11:18 AM, Adam Moffett wrote: > > Is Cat5 the default setting? So in recovery console mode you'd have the > Cat5 and you could get in on 169.254.1.1? > > > https://community.cambiumnetworks.com/t/how-to-enter-default-mode-or-recovery-console-for-450b-450i-and-450m-series-products/44936 > > > On 4/22/2021 12:14 PM, Nate Burke wrote: > > Not that I've found. It's a single drop down box to select the data path, > that's the only setting. I set it for Fiber, the Cat5 port still has a > physical link, but passes no traffic. > > I unplugged the Fiber cable, plugged my laptop into the cat5 and > rebooted. I got a handfull of pings through, (maybe 5 or 6) during the > bootup process, then it stopped responding completely. I thought maybe if > it had no Link during a boot it would automatically switch to the interface > with an active link, but no. > > On 4/22/2021 11:10 AM, Adam Moffett wrote: > > I don't have a 450m.... > > Can you have both ports on with different IP's? Even if they're not > bridged at least a way to back door in through the second port? > On 4/22/2021 12:07 PM, Nate Burke wrote: > > Oh, that's bad. A fully functional AP, hanging in the air, that's > completely unusable just because what should/can be redundant, isn't, > because of software. > > On 4/22/2021 10:58 AM, Josh Luthman wrote: > > It sucks. That's how it is. > > If it's 5 GHz you can do it over RF. If it's 3 GHz you can't because > it'll have to reach a SAS to transmit. > > Josh Luthman > 24/7 Help Desk: 937-552-2340 > Direct: 937-552-2343 > 1100 Wayne St > Suite 1337 > Troy, OH 45373 > > > On Thu, Apr 22, 2021 at 11:14 AM Nate Burke <n...@blastcomm.com> wrote: > >> I'm getting ready to deploy my first set of 450M radios, from my bench >> testing, and reading through the manual, do you have to Choose which >> data path is active, Copper OR Fiber? And the only way to switch it if >> that path is down is to log into the Radio with an SM connection over >> the RF? That can't be right can it? >> >> The EPMP radios bridge the copper and Fiber inside the radio so both are >> active. That doesn't seem to be the case with the 450M. Does the 450M >> only allow one data path, and if it breaks your SOL unless you can gain >> sudo-physical access to the AP? I have be missing where you set the >> primary/secondary data path, but I haven't been able to find it yet. >> >> -- >> AF mailing list >> AF@af.afmug.com >> http://af.afmug.com/mailman/listinfo/af_af.afmug.com >> > > > > > > > > > > > > -- > AF mailing list > AF@af.afmug.com > http://af.afmug.com/mailman/listinfo/af_af.afmug.com >
-- AF mailing list AF@af.afmug.com http://af.afmug.com/mailman/listinfo/af_af.afmug.com
