Thanks!!! Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On May 23, 2015 8:17 AM, "Ken Hohhof" <[email protected]> wrote:
> http://www.alliedelec.com/phoenix-contact-5602192/70208161/ > > > *From:* Josh Luthman <[email protected]> > *Sent:* Friday, May 22, 2015 9:22 PM > *To:* [email protected] > *Subject:* Re: [AFMUG] NEMA enclosure with GFCI outlet > > Oh no I definitely do, remember I'm passing these costs to the customer! > > > Josh Luthman > Office: 937-552-2340 > Direct: 937-552-2343 > 1100 Wayne St > Suite 1337 > Troy, OH 45373 > > On Fri, May 22, 2015 at 7:27 PM, Ken Hohhof <[email protected]> wrote: > >> An electrician would consider two GFCI’s in series unprofessional. It >> does not provide any more protection, and in the even one of them trips, it >> is likely to cause confusion. >> >> That said, there are DIN rail mount GFCI modules with no outlet just the >> test and reset buttons, you could wire one ahead of the terminal block in >> the L-Com enclosure. Phoenix Contact makes them, I saw them at Allied for >> over $100. I assume you don’t want to pay that. >> >> >> *From:* Josh Luthman <[email protected]> >> *Sent:* Friday, May 22, 2015 4:46 PM >> *To:* [email protected] >> *Subject:* Re: [AFMUG] NEMA enclosure with GFCI outlet >> >> >> Right the outlets. Not inside the enclosure (at least mine). >> >> Josh Luthman >> Office: 937-552-2340 >> Direct: 937-552-2343 >> 1100 Wayne St >> Suite 1337 >> Troy, OH 45373 >> On May 22, 2015 5:43 PM, "Jaime Solorza" <[email protected]> >> wrote: >> >>> All outlets here at well sites are GFCI period. So u get used to it. >>> >>> Jaime Solorza >>> On May 22, 2015 2:36 PM, "George Skorup" <[email protected]> wrote: >>> >>>> NEC says you need one GFI device on a circuit. So tell them two is not >>>> code? :) >>>> >>>> On 5/22/2015 3:11 PM, Josh Luthman wrote: >>>> >>>> I'm using that enclosure now. Need to dremel room for a GFCI. >>>> >>>> I hate them as well. They're doing a breaker, GFCI and that will go to >>>> the GFCI in the box. That's what they want, so that's what I'm charging >>>> for. >>>> >>>> >>>> Josh Luthman >>>> Office: 937-552-2340 >>>> Direct: 937-552-2343 >>>> 1100 Wayne St >>>> Suite 1337 >>>> Troy, OH 45373 >>>> >>>> On Fri, May 22, 2015 at 3:37 PM, Josh Reynolds <[email protected]> >>>> wrote: >>>> >>>>> >>>>> http://www.l-com.com/productfinder/finderresults.aspx?ftype=ENCLOSURES&finderid=5&steps=14x12x7+Inch%7c120+VAC%7cNone >>>>> >>>>> Find one you can adapt, swap the outlet for a GFCI. >>>>> >>>>> Josh Reynolds >>>>> CIO, SPITwSPOTSwww.spitwspots.com >>>>> >>>>> On 05/22/2015 11:33 AM, Josh Luthman wrote: >>>>> >>>>> Gotta have both (customer requirement). >>>>> >>>>> >>>>> Josh Luthman >>>>> Office: 937-552-2340 >>>>> Direct: 937-552-2343 >>>>> 1100 Wayne St >>>>> Suite 1337 >>>>> Troy, OH 45373 >>>>> >>>>> On Fri, May 22, 2015 at 3:32 PM, Adam Moffett <[email protected]> >>>>> wrote: >>>>> >>>>>> You could wire your box to the load side of a separate outdoor GFCI. >>>>>> Then the GFCI can also act as a convenience outlet and disconnect switch. >>>>>> Just a thought. >>>>>> >>>>>> >>>>>> On 5/22/2015 3:29 PM, Josh Luthman wrote: >>>>>> >>>>>>> Does such a thing exist? My current plan is to take a small box >>>>>>> with a normal outlet and replace it, but that requires a bit of dremel >>>>>>> work >>>>>>> and hence won't look at pretty. >>>>>>> >>>>>>> I only need a small work space, looking at 14x12x7 right now. >>>>>>> >>>>>>> Josh Luthman >>>>>>> Office: 937-552-2340 >>>>>>> Direct: 937-552-2343 >>>>>>> 1100 Wayne St >>>>>>> Suite 1337 >>>>>>> Troy, OH 45373 >>>>>>> >>>>>> >>>>>> >>>>> >>>>> >>>>> >>>> >>>> >>>> >
