The block diagram shows 9 & 10 on PCIe. I have had performance issues on both 
of these ports and have pulled most 1200 routers from production.

 



 

 

 

From: Af [mailto:af-boun...@afmug.com] On Behalf Of George Skorup
Sent: Tuesday, August 04, 2015 2:17 PM
To: af@afmug.com
Subject: Re: [AFMUG] RB1200 ports 9&10

 

11, 12 and 13 on the 1100 each have dedicated PCIe lanes to the CPU. I haven't 
really seen any issues with them, at least on the 1100AHx2. I have one original 
1100 and one 1100AH left in the network and those aren't doing much. The bigger 
issue I've seen with the 1100AHx2 is the fans quit and the whole thing needs a 
power-cycle to get them going again. I've seen this on every single one I have 
deployed.

On 8/4/2015 1:06 PM, Mike Hammett wrote:

Whichever the last few ports are. Check the block diagrams on routerboard.com 
to see which ones are special. It's not EVERYTHING not ran through a switch 
chip, but darn near.



-----
Mike Hammett
Intelligent Computing Solutions
http://www.ics-il.com

 <https://www.facebook.com/ICSIL>  
<https://plus.google.com/+IntelligentComputingSolutionsDeKalb>  
<https://www.linkedin.com/company/intelligent-computing-solutions>  
<https://twitter.com/ICSIL> 

Midwest Internet Exchange
http://www.midwest-ix.com

 <https://www.facebook.com/mdwestix>  
<https://www.linkedin.com/company/midwest-internet-exchange>  
<https://twitter.com/mdwestix> 


  _____  


From: "Adam Moffett"  <mailto:dmmoff...@gmail.com> <dmmoff...@gmail.com>
To: af@afmug.com
Sent: Tuesday, August 4, 2015 1:05:09 PM
Subject: Re: [AFMUG] RB1200 ports 9&10

RB1xxx ? So is this an issue with the 1100 also?



On 8/4/2015 2:01 PM, Mike Hammett wrote:

The last couple ports on the RB1xxx series...  suck.



-----
Mike Hammett
Intelligent Computing Solutions
http://www.ics-il.com

 <https://www.facebook.com/ICSIL>  
<https://plus.google.com/+IntelligentComputingSolutionsDeKalb>  
<https://www.linkedin.com/company/intelligent-computing-solutions>  
<https://twitter.com/ICSIL> 

Midwest Internet Exchange
http://www.midwest-ix.com

 <https://www.facebook.com/mdwestix>  
<https://www.linkedin.com/company/midwest-internet-exchange>  
<https://twitter.com/mdwestix> 


  _____  


From: "Adam Moffett"  <mailto:dmmoff...@gmail.com> <dmmoff...@gmail.com>
To: af@afmug.com
Sent: Tuesday, August 4, 2015 1:00:14 PM
Subject: [AFMUG] RB1200 ports 9&10

I just read a forum post saying that ports 9&10 on the RB1200 
underperform compared to the other ports.

Does anyone know how bad that underperformance is?  I've been pulling my 
hair out for days chasing a performance issue on a backhaul, and it 
turns out one end of it is plugged into port9 on an RB1200.

Could it make my 200 meg link only do 90meg?

 

 

 

 

Reply via email to