It would be a bear to get it mounted on the towers . I asked more out of curiosity. We use omni antennas as a fall back if a sector fails. Since we are converting existing towers and deploying new towers with 450i 900 I would love to run 4 90 degree sectors with an omni above or below them. 10mhz channels on the sectors and a 5mhz on the omni. We try and have redundancy on every AP and backhaul I just have not settled on a good way to do it with the 450i 900 yet.
Best regards, Brandon Yuchasz GogebicRange.net www.gogebicrange.net <http://www.gogebicrange.net/> From: Af [mailto:af-boun...@afmug.com] On Behalf Of Ken Hohhof Sent: Monday, February 29, 2016 4:19 PM To: af@afmug.com Subject: Re: [AFMUG] Laird ODH9-9 or Alternative What Chuck is talking about would I guess be similar to this: http://alphaantennas.com/products/small-cells/aw3464/ I’d hate to see that thing twice as big. From: Eric Kuhnke <mailto:eric.kuh...@gmail.com> Sent: Monday, February 29, 2016 3:57 PM To: af@afmug.com Subject: Re: [AFMUG] Laird ODH9-9 or Alternative I'm imagining a 900 MHz yagi arms race with 6' length and a whole cast iron bathtub behind the mounting for rear/side shielding. The rf armor guy will probably sell a kit for $899... On Feb 29, 2016 8:50 AM, "Chuck McCown" <ch...@wbmfg.com> wrote: Roughly double the size for every 3 dB improvement in gain. From: Brandon Yuchasz <mailto:li...@gogebicrange.net> Sent: Monday, February 29, 2016 9:49 AM To: af@afmug.com Subject: Re: [AFMUG] Laird ODH9-9 or Alternative Chuck how big would an antenna have to get to get up into the 9 or 10 dB range? Best regards, Brandon Yuchasz GogebicRange.net www.gogebicrange.net <http://www.gogebicrange.net/> From: Af [mailto:af-boun...@afmug.com] On Behalf Of Chuck McCown Sent: Wednesday, February 24, 2016 5:01 PM To: af@afmug.com Subject: Re: [AFMUG] Laird ODH9-9 or Alternative Depends on gain. 6 dB would probably be 5 feet tall. From: Mathew Howard <mailto:mhoward...@gmail.com> Sent: Wednesday, February 24, 2016 4:00 PM To: af <mailto:af@afmug.com> Subject: Re: [AFMUG] Laird ODH9-9 or Alternative How tall would something like that be? On Wed, Feb 24, 2016 at 4:53 PM, Chuck McCown <ch...@wbmfg.com> wrote: I did a nice 6 dB H pol omni a few years ago. Never released it. I could do a dual slant 900 omni. It would be probably 8 inches in diameter. From: Chuck Hogg <mailto:ch...@shelbybb.com> Sent: Wednesday, February 24, 2016 3:51 PM To: af@afmug.com Subject: Re: [AFMUG] Laird ODH9-9 or Alternative 9dB is what we have now. Regards, Chuck On Wed, Feb 24, 2016 at 4:39 PM, Chuck McCown <ch...@wbmfg.com> wrote: How much gain are you looking for? From: Chuck Hogg <mailto:ch...@shelbybb.com> Sent: Wednesday, February 24, 2016 2:36 PM To: af@afmug.com ; memb...@wispa.org Subject: [AFMUG] Laird ODH9-9 or Alternative Hello: I recently just tried to get an ODH9-9 900MHz Horizontal Omni, to find out they quit making it. Every few years they have to be replaced because the internals rust out, but we are used to identifying the issue and replacing them when it happens. So, does anyone have any NIB ODH9-9 omnis they are willing to part with? Or am I going to have to switch to Amphenol? Regards, Chuck