Hmmm... in that case.. the question would be... How do you mount the radio to the Adapter plate.
There needs to be a mateing adapter on your plate side... That piece only comes with the UBNT Dish... (you can pull up the UBNT 10ghz Dish Userguide to see that ...) Jiruos adapters that we used, required that piece to be removed from the AF11x so that it could be screwed in directly (as per my picture). I was told that they were going to redesign so that they would have a mateing bracket on their side so that the AF11x would slide in. (You will also need to have to include cables to connect to AF11x to the Feed horn .. I am sure you already knew that). Regards Faisal Imtiaz Snappy Internet & Telecom 7266 SW 48 Street Miami, FL 33155 Tel: 305 663 5518 x 232 Help-desk: (305)663-5518 Option 2 or Email: supp...@snappytelecom.net > From: ch...@wbmfg.com > To: af@afmug.com > Sent: Thursday, October 5, 2017 10:45:45 AM > Subject: Re: [AFMUG] Fw: AF11x adapters > No because my design presumes the adapter will be there to space the radio out > away from the end of the waveguide transition. Without that extra spacing the > radio would crash into the end of the adapter. > From: Mathew Howard > Sent: Thursday, October 5, 2017 8:42 AM > To: af > Subject: Re: [AFMUG] Fw: AF11x adapters > Wouldn't it work without the adapter anyway? If I'm remembering right, with > the > Jirous adapters, you take the snap adapter off and just bolt the radio > directly > to their mounting plate using the same holes... wouldn't that line up with > your > adapter too? > On Thu, Oct 5, 2017 at 9:33 AM, < ch...@wbmfg.com > wrote: >> If that plastic slide/snap adapter is included with each radio, then we >> should >> be good. >> I designed the spacing and everything assuming that adapter would be used >> with >> each unit. >> From: Faisal Imtiaz >> Sent: Thursday, October 5, 2017 8:28 AM >> To: af@afmug.com >> Subject: Re: [AFMUG] Fw: AF11x adapters >> Picture of the Jirous Adapter attached.... >> rest of the answers are inline below. >> If you have any questions, feel free to call me. >> Regards. >> Faisal Imtiaz >> Snappy Internet & Telecom >> 7266 SW 48 Street >> Miami, FL 33155 >> Tel: 305 663 5518 x 232 >> Help-desk: (305)663-5518 Option 2 or Email: supp...@snappytelecom.net >>> From: "Chuck McCown" < ch...@wbmfg.com > >>> To: af@afmug.com >>> Sent: Thursday, October 5, 2017 8:58:26 AM >>> Subject: [AFMUG] Fw: AF11x adapters >>> Made Gino some adapters so he can use AF11x radios on Remec mount antennas. >>> I made the hole pattern to match a plastic slide and snap adapter that came >>> with >>> the radio I have. >> That should be fine >>> But not sure if that part is included with all AF11X radios. Gino is asking >>> about how the radio is supposed to mount to my adapter. >>> If the slide/snap is not automatically included in all shipments, I need to >>> alter the bolt pattern to allow mounting of the radio when that part is not >>> present. He needs some more of these adapters and I want to make sure to >>> send >>> him stuff that does not require any work on his part. >>> Do you AF11X users know if that slid/snap adapter plate is included with all >>> radios? >> Yes that slide/snap adapter is included with each of the AF11x (That is how >> they >> slide/attach to the UBNT dishes). >>> If so, can we buy more for Gino to use right now in the event he has lost >>> his? >>> If not how should I alter the mount so the radio can still fit onto the >>> adapter?
