Hi,
If you modify init.xxx.rc to let it don't mount /system etc, like below.
on fs
# mount ext4 partitions
mount ext4 /dev/block/mmcblk0p5 /system
mount ext4 /dev/block/mmcblk0p5 /system ro remount
mount ext4 /dev/block/mmcblk0p7 /data nosuid nodev nodiratime noatime
noauto_da_alloc
mount ext4 /dev/block/mmcblk0p6 /cache nosuid nodev
mount ext4 /dev/block/mmcblk0p8 /vendor nosuid nodev
you should also delete "on fs" too, if the "on fs" without any command, the
init process will meet segment fault, so the init will kill him self.
Best regards,
Zhang Jiejing
2012/4/3 Ki Seok Park <katsu.bo...@gmail.com>
> host : ubuntu 10.04 x64
> android : google.gingerbread 2.3.3_r1
> kernel : android.kernel 2.6.35.7
>
> Hi.
>
> I have a some board, using samsung s5pv210.
>
> when Android is booting(on NAND), servicemanager is die.
>
>
> ------------------------------------------------------------------------------------
> request_suspend_state:wakeup (0->0) at 20730120503 (2011-01-01
> 12:00:20.112335668 UTC)
> init: untracked pid 79 exited
> init: untracked pid 87 exited
> init: untracked pid 94 exited
> init: untracked pid 95 exited
> request_suspend_state: wakeup (0->0) at 25385392045
> (2011-01-0112:00:24.767607335 UTC)
> init: untracked pid 89 exited
> init: untracked pid 98 exited
> init: critical process 'servicemanager' exited 4 times in 4
> minutes;rebooting into recovery mode
> Restarting system with command 'recovery'.
>
> ------------------------------------------------------------------------------------
>
> so, I should try to boot, gdb debugging via NFS booting.
>
> However, when booting form NFS, other problems will occur.
>
> that is. KERNEL - PANIC.....
>
>
> ------------------------------------------------------------------------------------
> net eth0: SMSC911x/921x identified at 0xf088e000, IRQ: 43
> IP-Config: Complete:
> device=eth0, addr=192.168.0.111, mask=255.255.255.0,
> gw=192.168.0.254,
> host=192.168.0.111, domain=, nis-domain=(none),
> bootserver=192.168.0.100, rootserver=192.168.0.100, rootpath=
> DBUG_PORT must not use AFC!
> Looking up port of RPC 100003/2 on 192.168.0.100
> Looking up port of RPC 100005/1 on 192.168.0.100
> VFS: Mounted root (nfs filesystem) on device 0:14.
> Freeing init memory: 156K
> init: cannot open '/initlogo.rle'
> Kernel panic - not syncing: Attempted to kill init!
>
> ------------------------------------------------------------------------------------
> (kernel/exit.c)
>
> so. I want to trace android ,kernel booting mecanism using gdb or
> strace.
>
> how can i do?
>
> and how can I solve this problem?
>
> NFS always problem......
>
> (kernel source was provided Board company. Android source too.)
>
> But I want to build, through Google.Reference source.
>
> when booting from Board company source, that is good operating.
>
> but my gingerbread source is trouble.
>
> i think it is kernel problem. but only android source changed.
>
>
>
>
> THIS IS MY NFS BOOTING MESSAGE.
>
> ------------------------------------------------------------------------------------
> U-Boot 1.3.4 (Mar 23 2012 - 01:38:16) for MANGO210
>
>
> CPU: S5PV210@1000MHz(OK)
> APLL = 1000MHz, HclkMsys = 200MHz, PclkMsys = 100MHz
> MPLL = 667MHz, EPLL = 80MHz
> HclkDsys = 166MHz, PclkDsys = 83MHz
> HclkPsys = 133MHz, PclkPsys = 66MHz
> SCLKA2M = 200MHz
> Serial = CLKUART
> Board: MANGO210
> DRAM: 512 MB
> SD/MMC: 7647MB
> NAND: 256 MB
> In: serial
> Out: serial
> Err: serial
> checking mode for fastboot ...
>
> U-Boot 1.3.4 (Mar 23 2012 - 01:38:16) for MANGO210
>
>
> CPU: S5PV210@1000MHz(OK)
> APLL = 1000MHz, HclkMsys = 200MHz, PclkMsys = 100MHz
> MPLL = 667MHz, EPLL = 80MHz
> HclkDsys = 166MHz, PclkDsys = 83MHz
> HclkPsys = 133MHz, PclkPsys = 66MHz
> SCLKA2M = 200MHz
> Serial = CLKUART
> Board: MANGO210
> DRAM: 512 MB
> SD/MMC: 7647MB
> NAND: 256 MB
> In: serial
> Out: serial
> Err: serial
> checking mode for fastboot ...
> Hit any key to stop autoboot: 0
> smc911x: initializing
> smc911x: detected LAN9220 controller
> smc911x: phy initialized
> smc911x: MAC 00:40:5c:26:0a:5b
> TFTP from server 192.168.0.100; our IP address is 192.168.0.111
> Filename 'Gingerbread.Patch.zImage'.
> Load address: 0x21000000
> Loading:
> #################################################################
>
> #################################################################
>
> #################################################################
>
> #################################################################
> #####################################
> done
> Bytes transferred = 4351908 (0x4267a4)
> Boot with zImage
>
> Starting kernel ...
>
> Uncompressing Linux... done, booting the kernel.
> Initializing cgroup subsys cpu
> Linux version 2.6.35.7 (liverpool@laptop-server) (gcc version 4.4.1
> (Sourcery G++ Lite 2009q3-67) ) #1 PREEMPT Mon Apr 2 16:38:24 KST 2012
> CPU: ARMv7 Processor [412fc082] revision 2 (ARMv7), cr=10c53c7f
> CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
> Machine: MANGO210
> Ignoring unrecognised tag 0x00000000
> Ignoring unrecognised tag 0x00000000
> Ignoring unrecognised tag 0x41001099
> Memory policy: ECC disabled, Data cache writeback
> CPU S5PV210/S5PC110 (id 0x43110220)
> S3C24XX Clocks, Copyright 2004 Simtec Electronics
> S5PV210: PLL settings, A=1000000000, M=667000000, E=80000000
> V=54000000
> S5PV210: ARMCLK=1000000000, HCLKM=200000000, HCLKD=166750000
> HCLKP=133400000, PCLKM=100000000, PCLKD=83375000, PCLKP=66700000
> sclk_dmc: source is sclk_a2m (0), rate is 200000000
> sclk_onenand: source is hclk_dsys (1), rate is 166750000
> sclk: source is mout_mpll (6), rate is 66700000
> sclk: source is mout_mpll (6), rate is 66700000
> sclk: source is mout_mpll (6), rate is 66700000
> sclk: source is mout_mpll (6), rate is 66700000
> sclk_mixer: source is sclk_dac (0), rate is 54000000
> sclk_spdif: source is sclk_audio (0), rate is 24000000
> sclk_fimc: source is ext_xtal (0), rate is 24000000
> sclk_fimc: source is ext_xtal (0), rate is 24000000
> sclk_fimc: source is ext_xtal (0), rate is 24000000
> sclk_cam0: source is ext_xtal (0), rate is 24000000
> sclk_cam1: source is ext_xtal (0), rate is 24000000
> sclk_fimd: source is ext_xtal (0), rate is 24000000
> sclk_mmc: source is mout_mpll (6), rate is 47642857
> sclk_mmc: source is mout_epll (7), rate is 80000000
> sclk_mmc: source is mout_epll (7), rate is 80000000
> sclk_mmc: source is mout_epll (7), rate is 80000000
> sclk_mfc: source is sclk_a2m (0), rate is 200000000
> sclk_g2d: source is sclk_a2m (0), rate is 200000000
> sclk: source is sclk_a2m (0), rate is 200000000
> sclk_csis: source is ext_xtal (0), rate is 24000000
> sclk_spi: source is ext_xtal (0), rate is 24000000
> sclk_spi: source is ext_xtal (0), rate is 24000000
> sclk_pwi: source is ext_xtal (0), rate is 24000000
> sclk_pwm: source is ext_xtal (0), rate is 24000000
> sclk_mdnie: source is ext_xtal (0), rate is 24000000
> sclk_mdnie_pwm: source is ext_xtal (0), rate is 24000000
> s5pv210: 37748736 bytes system memory reserved for mfc at 0x20c6f000
> s5pv210: 37748736 bytes system memory reserved for mfc at 0x40000000
> s5pv210: 6144000 bytes system memory reserved for fimc0 at 0x42400000
> s5pv210: 6144000 bytes system memory reserved for fimc1 at 0x429dc000
> s5pv210: 6144000 bytes system memory reserved for fimc2 at 0x42fb8000
> s5pv210: 6144000 bytes system memory reserved for jpeg at 0x43594000
> s5pv210: 6144000 bytes system memory reserved for fimd at 0x43b70000
> s5pv210: 1536000 bytes system memory reserved for texstream at
> 0x4414c000
> s5pv210: 1536000 bytes system memory reserved for pmem_gpu1 at
> 0x442c3000
> s5pv210: 6144000 bytes system memory reserved for g2d at 0x4443a000
> Built 1 zonelists in Zone order, mobility grouping on. Total pages:
> 129536
> Kernel command line: root=/dev/nfs rw nfsroot=192.168.0.100:/home/
> liverpool/src/Gingerbread/PATCH.by_park/NFSROOT, nolock
> ip=192.168.0.111:192.168.0.100:192.168.0.254:255.255.255.0::eth0:off
> init=/init console=ttySAC1,115200
> PID hash table entries: 2048 (order: 1, 8192 bytes)
> Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
> Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
> Memory: 256MB 256MB = 512MB total
> Memory: 398460k/398460k available, 125828k reserved, 0K highmem
> Virtual kernel memory layout:
> vector : 0xffff0000 - 0xffff1000 ( 4 kB)
> fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
> DMA : 0xff000000 - 0xffe00000 ( 14 MB)
> vmalloc : 0xf0800000 - 0xfc000000 ( 184 MB)
> lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
> modules : 0xbf000000 - 0xc0000000 ( 16 MB)
> .init : 0xc0008000 - 0xc002f000 ( 156 kB)
> .text : 0xc002f000 - 0xc0760000 (7364 kB)
> .data : 0xc0760000 - 0xc07a8660 ( 290 kB)
> SLUB: Genslabs=9, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
> Hierarchical RCU implementation.
> RCU-based detection of stalled CPUs is disabled.
> Verbose stalled-CPUs detection is disabled.
> NR_IRQS:393
> VIC @fd000000: id 0x00041192, vendor 0x41
> VIC @fd010000: id 0x00041192, vendor 0x41
> VIC @fd020000: id 0x00041192, vendor 0x41
> VIC @fd030000: id 0x00041192, vendor 0x41
> mult[140737]
> max_delta_ns[2937815369]
> min_delta_ns[30517]
> rate[32768]
> HZ[256]
> Console: colour dummy device 80x30
> console [ttySAC1] enabled
> Calibrating delay loop... 998.15 BogoMIPS (lpj=1949696)
> pid_max: default: 32768 minimum: 301
> Security Framework initialized
> SELinux: Initializing.
> Mount-cache hash table entries: 512
> Initializing cgroup subsys debug
> Initializing cgroup subsys cpuacct
> Initializing cgroup subsys freezer
> CPU: Testing write buffer coherency: ok
> NET: Registered protocol family 16
> S3C Power Management, Copyright 2004 Simtec Electronics
> pmstats at 00000000
> mango210_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857
> mango210_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857
> mango210_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857
> mango210_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857
> S5PV210: Initializing architecture
> s3c24xx-pwm s3c24xx-pwm.0: tin at 66700000, tdiv at 66700000,
> tin=divclk, base 0
> s3c24xx-pwm s3c24xx-pwm.1: tin at 66700000, tdiv at 66700000,
> tin=divclk, base 8
> s3c24xx-pwm s3c24xx-pwm.2: tin at 66700000, tdiv at 66700000,
> tin=divclk, base 12
> s3c24xx-pwm s3c24xx-pwm.3: tin at 66700000, tdiv at 66700000,
> tin=divclk, base 16
> bio: create slab <bio-0> at 0
> SCSI subsystem initialized
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> i2c-gpio i2c-gpio.0: using pins 40 (SDA) and 41 (SCL)
> i2c-gpio i2c-gpio.2: using pins 44 (SDA) and 45 (SCL)
> s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
> Advanced Linux Sound Architecture Driver Version 1.0.23.
> Switching to clocksource clock_source_systimer
> NET: Registered protocol family 2
> IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
> TCP established hash table entries: 16384 (order: 5, 131072 bytes)
> TCP bind hash table entries: 16384 (order: 6, 327680 bytes)
> TCP: Hash tables configured (established 16384 bind 16384)
> TCP reno registered
> UDP hash table entries: 256 (order: 1, 12288 bytes)
> UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
> NET: Registered protocol family 1
> RPC: Registered udp transport module.
> RPC: Registered tcp transport module.
> RPC: Registered tcp NFSv4.1 backchannel transport module.
> PMU: registered new PMU device of type 0
> MANGO210 wifi init function
> MANGO210 RTC, (c) 2010 Samsung Electronics
> mango210-rtc mango210-rtc: rtc disabled, re-enabling
> mango210-rtc mango210-rtc: rtc core: registered s3c as rtc0
> S5PV210 ADC driver, (c) 2010 Samsung Electronics
> cpuidle: phy_regs_save:0x4fd7e000
> Loaded driver for PL330 DMAC-0 s3c-pl330
> DBUFF-64x8bytes Num_Chans-8 Num_Peri-2 Num_Events-32
> Loaded driver for PL330 DMAC-1 s3c-pl330
> DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
> Loaded driver for PL330 DMAC-2 s3c-pl330
> DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
> audit: initializing netlink socket (disabled)
> type=2000 audit(0.792:1): initialized
> ashmem: initialized
> msgmni has been set to 778
> alg: No test for stdrng (krng)
> io scheduler noop registered
> io scheduler deadline registered
> io scheduler cfq registered (default)
> s3cfb s3cfb: [fb2] dma: 0x43b70000, cpu: 0xf1000000, size: 0x005dc000
> FIMD src sclk = 166750000
> s3cfb s3cfb: registered successfully
> Start display and show logo
> ipwireless 1.1 by Stephen Blackheath, Ben Martel, Jiri Kosina and
> David Sterba
> PA FB = 0x43B70000, bits per pixel = 32
> screen width=800 height=480 va=0xe3b70000 pa=0x43b70000
> xres_virtual = 800, yres_virtual = 1920, xoffset = 0, yoffset = 0
> fb_size=6144000
> Back frameBuffer[0].VAddr=e3ce7000 PAddr=43ce7000 size=1536000
> Back frameBuffer[1].VAddr=e3e5e000 PAddr=43e5e000 size=1536000
> Back frameBuffer[2].VAddr=e3fd5000 PAddr=43fd5000 size=1536000
> s5pv210-uart.0: s3c2410_serial0 at MMIO 0xe2900000 (irq = 16) is a
> S3C6400/10
> s5pv210-uart.1: s3c2410_serial1 at MMIO 0xe2900400 (irq = 20) is a
> S3C6400/10
> s5pv210-uart.2: s3c2410_serial2 at MMIO 0xe2900800 (irq = 24) is a
> S3C6400/10
> s5pv210-uart.3: s3c2410_serial3 at MMIO 0xe2900c00 (irq = 28) is a
> S3C6400/10
> brd: module loaded
> loop: module loaded
> pmem_gpu1: 1 init
> Android kernel panic handler initialized (bind=kpanic)
> S3C NAND Driver, (c) 2008 Samsung Electronics
> S3C NAND Driver is using hardware ECC.
> NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB
> 3,3V 8-bit)
> Creating 6 MTD partitions on "s5pv210-nand":
> 0x000000000000-0x000000100000 : "bootloader"
> 0x000000100000-0x000000600000 : "recovery"
> 0x000000600000-0x000000b00000 : "kernel"
> 0x000000b00000-0x000000e00000 : "ramdisk"
> 0x000000e00000-0x000008600000 : "system"
> 0x000008600000-0x000010000000 : "userdata"
> PPP generic driver version 2.4.2
> PPP Deflate Compression module registered
> PPP BSD Compression module registered
> smsc911x: Driver version 2008-10-21.
> smsc911x-mdio: probed
> eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01,
> irq=-1)
> net eth0: MAC Address: 96:5b:9c:31:68:43
> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> s5p-ehci s5p-ehci: s5pv210 EHCI
> s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
> s5p-ehci s5p-ehci: irq 87, io mem 0xec200000
> s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 1 port detected
> ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
> s5p-ohci s5p-ohci: s5pv210 OHCI
> s5p-ohci s5p-ohci: new USB bus registered, assigned bus number 2
> s5p-ohci s5p-ohci: irq 87, io mem 0xec300000
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 1 port detected
> Initializing USB Mass Storage driver...
> usbcore: registered new interface driver usb-storage
> USB Mass Storage support registered.
> s3c-udc : S3C HS USB Device Controller Driver, (c) 2008-2009 Samsung
> Electronics
> s3c-udc : version 15 March 2009 (DMA Mode)
> android init
> android_probe pdata: c076cf78
> android_bind
> android_usb gadget: android_usb ready
> f_acm init
> android_register_function acm
> f_adb init
> android_register_function adb
> f_mass_storage init
> fsg_probe pdev: c076bdf0, pdata: c076cf9c
> android_register_function usb_mass_storage
> f_mtp init
> android_register_function mtp
> f_rndis init
> android_register_function rndis
> rndis_function_bind_config MAC: 00:00:00:00:00:00
> android_usb gadget: using random self ethernet address
> android_usb gadget: using random host ethernet address
> usb0: MAC 9a:ee:1e:73:98:89
> usb0: HOST MAC 92:4d:00:ca:f5:46
> android_usb gadget: Mass Storage Function, version: 2009/09/11
> android_usb gadget: Number of LUNs=1
> lun0: LUN: removable file: (no medium)
> adb_bind_config
> mtp_bind_config
> mice: PS/2 mouse device common for all mice
> input: mango-keys as /devices/platform/mango-keys.0/input/input0
> start MANGO GPIO Button V1.1
> vd5376 0-0053: vd5376 initialization failed
> vd5376 2-0053: vd5376 initialization failed
> S5P Touchscreen driver, (c) 2008 Samsung Electronics
> S5P TouchScreen got loaded successfully : 12 bits
> input: S5P TouchScreen as /devices/virtual/input/input1
> using rtc device, s3c, for alarms
> i2c /dev entries driver
> Linux video capture interface: v2.00
> mfc_init: <6>S5PC110 MFC Driver, (c) 2009 Samsung Electronics
> S3C JPEG Driver, (c) 2007 Samsung Electronics
> JPEG driver for S5PV210
> i2c i2c-1: attached s5p_ddc into i2c adapter successfully
> S5PC11X HPD Driver, (c) 2009 Samsung Electronics
> S5PC11X CEC Driver, (c) 2009 Samsung Electronics
> s3c_bat_init
> sec-fake-battery sec-fake-battery: s3c_bat_probe
> device-mapper: uevent: version 1.0.3
> device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-
> de...@redhat.com
> cpuidle: using governor ladder
> cpuidle: using governor menu
> sdhci: Secure Digital Host Controller Interface driver
> sdhci: Copyright(c) Pierre Ossman
> s3c-sdhci s3c-sdhci.3: clock source 0: hsmmc (133400000 Hz)
> s3c-sdhci s3c-sdhci.3: clock source 1: hsmmc (133400000 Hz)
> s3c-sdhci s3c-sdhci.3: clock source 2: sclk_mmc (47642857 Hz)
> mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.3] using ADMA
> s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133400000 Hz)
> s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133400000 Hz)
> s3c-sdhci s3c-sdhci.1: clock source 2: sclk_mmc (47642857 Hz)
> mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
> s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133400000 Hz)
> s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133400000 Hz)
> s3c-sdhci s3c-sdhci.0: clock source 2: sclk_mmc (47642857 Hz)
> mmc2: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
> s3c-sdhci s3c-sdhci.2: clock source 0: hsmmc (133400000 Hz)
> s3c-sdhci s3c-sdhci.2: clock source 1: hsmmc (133400000 Hz)
> s3c-sdhci s3c-sdhci.2: clock source 2: sclk_mmc (47642857 Hz)
> mmc3: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using ADMA
> usbcore: registered new interface driver usbhid
> usbhid: USB HID core driver
> logger: created 64K log 'log_main'
> logger: created 256K log 'log_events'
> logger: created 64K log 'log_radio'
> logger: created 64K log 'log_system'
> wm8960 0-001a: No platform data supplied
> android_usb gadget: high speed config #1: Android Composite
> mmc0: new high speed SDIO card at address 0001
> s3c_idma_preallocate_buffer: VA-f08c0000 PA-C0000000 163840bytes
> asoc: WM8960 <-> s3c64xx-i2s mapping ok
> s3c_idma_preallocate_buffer: VA-f0900000 PA-C0000000 163840bytes
> asoc: WM8960 <-> s3c64xx-i2s mapping ok
> mmc2: new high speed SDHC card at address b368
> mmcblk0: mmc2:b368 USD 7.46 GiB
> mmcblk0: p1 p2 p3
> ASoC: Failed to create HP-L/R debugfs file
> ASoC: Failed to create Speaker-L/R debugfs file
> asoc: DIT <-> samsung-spdif mapping ok
> ALSA device list:
> #0: mango (WM8960)
> #1: SMDK (spdif-dit)
> Netfilter messages via NETLINK v0.30.
> nf_conntrack version 0.5.0 (6225 buckets, 24900 max)
> ip_tables: (C) 2000-2006 Netfilter Core Team
> arp_tables: (C) 2002 David S. Miller
> TCP cubic registered
> NET: Registered protocol family 17
> Bridge firewalling registered
> Ebtables v2.0 registered
> ThumbEE CPU extension supported.
> VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev
> 2
> mango210-rtc mango210-rtc: rtc disabled, re-enabling
> mango210-rtc mango210-rtc: setting system clock to 2011-01-01 12:00:02
> UTC (1293883202)
> FIMC0 registered successfully
> FIMC1 registered successfully
> FIMC2 registered successfully
> <6>S5PC1XX TVOUT Driver, (c) 2009 Samsung Electronics
> s5p-tvout s5p-tvout: hpd status is cable removed
> [CRZ] SD/MMC channel 2 bus width : 1
> [CRZ] sdhci_s3c_set_clock max_clock 47642857
> [CRZ] SD/MMC channel 2 bus width : 1
> [CRZ] SD/MMC channel 2 bus width : 1
> net eth0: SMSC911x/921x identified at 0xf088e000, IRQ: 43
> IP-Config: Complete:
> device=eth0, addr=192.168.0.111, mask=255.255.255.0,
> gw=192.168.0.254,
> host=192.168.0.111, domain=, nis-domain=(none),
> bootserver=192.168.0.100, rootserver=192.168.0.100, rootpath=
> DBUG_PORT must not use AFC!
> Looking up port of RPC 100003/2 on 192.168.0.100
> Looking up port of RPC 100005/1 on 192.168.0.100
> VFS: Mounted root (nfs filesystem) on device 0:14.
> Freeing init memory: 156K
> init: cannot open '/initlogo.rle'
> Kernel panic - not syncing: Attempted to kill init!
> Rebooting in 5 seconds..▒▒▒▒▒▒OK
>
> ------------------------------------------------------------------------------------
>
> --
> unsubscribe: android-kernel+unsubscr...@googlegroups.com
> website: http://groups.google.com/group/android-kernel
--
unsubscribe: android-kernel+unsubscr...@googlegroups.com
website: http://groups.google.com/group/android-kernel
