The problem can also be on the server side (in most cases it is). Did you check the firewall running on the server?
On Sat, May 5, 2012 at 8:46 AM, Jiejing.Zhang <kzj...@gmail.com> wrote: > Hi, > > If you modify init.xxx.rc to let it don't mount /system etc, like below. > > on fs > # mount ext4 partitions > mount ext4 /dev/block/mmcblk0p5 /system > mount ext4 /dev/block/mmcblk0p5 /system ro remount > mount ext4 /dev/block/mmcblk0p7 /data nosuid nodev nodiratime noatime > noauto_da_alloc > mount ext4 /dev/block/mmcblk0p6 /cache nosuid nodev > mount ext4 /dev/block/mmcblk0p8 /vendor nosuid nodev > > you should also delete "on fs" too, if the "on fs" without any command, > the init process will meet segment fault, so the init will kill him self. > > Best regards, > Zhang Jiejing > > > > 2012/4/3 Ki Seok Park <katsu.bo...@gmail.com> > >> host : ubuntu 10.04 x64 >> android : google.gingerbread 2.3.3_r1 >> kernel : android.kernel 2.6.35.7 >> >> Hi. >> >> I have a some board, using samsung s5pv210. >> >> when Android is booting(on NAND), servicemanager is die. >> >> >> ------------------------------------------------------------------------------------ >> request_suspend_state:wakeup (0->0) at 20730120503 (2011-01-01 >> 12:00:20.112335668 UTC) >> init: untracked pid 79 exited >> init: untracked pid 87 exited >> init: untracked pid 94 exited >> init: untracked pid 95 exited >> request_suspend_state: wakeup (0->0) at 25385392045 >> (2011-01-0112:00:24.767607335 UTC) >> init: untracked pid 89 exited >> init: untracked pid 98 exited >> init: critical process 'servicemanager' exited 4 times in 4 >> minutes;rebooting into recovery mode >> Restarting system with command 'recovery'. >> >> ------------------------------------------------------------------------------------ >> >> so, I should try to boot, gdb debugging via NFS booting. >> >> However, when booting form NFS, other problems will occur. >> >> that is. KERNEL - PANIC..... >> >> >> ------------------------------------------------------------------------------------ >> net eth0: SMSC911x/921x identified at 0xf088e000, IRQ: 43 >> IP-Config: Complete: >> device=eth0, addr=192.168.0.111, mask=255.255.255.0, >> gw=192.168.0.254, >> host=192.168.0.111, domain=, nis-domain=(none), >> bootserver=192.168.0.100, rootserver=192.168.0.100, rootpath= >> DBUG_PORT must not use AFC! >> Looking up port of RPC 100003/2 on 192.168.0.100 >> Looking up port of RPC 100005/1 on 192.168.0.100 >> VFS: Mounted root (nfs filesystem) on device 0:14. >> Freeing init memory: 156K >> init: cannot open '/initlogo.rle' >> Kernel panic - not syncing: Attempted to kill init! >> >> ------------------------------------------------------------------------------------ >> (kernel/exit.c) >> >> so. I want to trace android ,kernel booting mecanism using gdb or >> strace. >> >> how can i do? >> >> and how can I solve this problem? >> >> NFS always problem...... >> >> (kernel source was provided Board company. Android source too.) >> >> But I want to build, through Google.Reference source. >> >> when booting from Board company source, that is good operating. >> >> but my gingerbread source is trouble. >> >> i think it is kernel problem. but only android source changed. >> >> >> >> >> THIS IS MY NFS BOOTING MESSAGE. >> >> ------------------------------------------------------------------------------------ >> U-Boot 1.3.4 (Mar 23 2012 - 01:38:16) for MANGO210 >> >> >> CPU: S5PV210@1000MHz(OK) >> APLL = 1000MHz, HclkMsys = 200MHz, PclkMsys = 100MHz >> MPLL = 667MHz, EPLL = 80MHz >> HclkDsys = 166MHz, PclkDsys = 83MHz >> HclkPsys = 133MHz, PclkPsys = 66MHz >> SCLKA2M = 200MHz >> Serial = CLKUART >> Board: MANGO210 >> DRAM: 512 MB >> SD/MMC: 7647MB >> NAND: 256 MB >> In: serial >> Out: serial >> Err: serial >> checking mode for fastboot ... >> >> U-Boot 1.3.4 (Mar 23 2012 - 01:38:16) for MANGO210 >> >> >> CPU: S5PV210@1000MHz(OK) >> APLL = 1000MHz, HclkMsys = 200MHz, PclkMsys = 100MHz >> MPLL = 667MHz, EPLL = 80MHz >> HclkDsys = 166MHz, PclkDsys = 83MHz >> HclkPsys = 133MHz, PclkPsys = 66MHz >> SCLKA2M = 200MHz >> Serial = CLKUART >> Board: MANGO210 >> DRAM: 512 MB >> SD/MMC: 7647MB >> NAND: 256 MB >> In: serial >> Out: serial >> Err: serial >> checking mode for fastboot ... >> Hit any key to stop autoboot: 0 >> smc911x: initializing >> smc911x: detected LAN9220 controller >> smc911x: phy initialized >> smc911x: MAC 00:40:5c:26:0a:5b >> TFTP from server 192.168.0.100; our IP address is 192.168.0.111 >> Filename 'Gingerbread.Patch.zImage'. >> Load address: 0x21000000 >> Loading: >> ################################################################# >> >> ################################################################# >> >> ################################################################# >> >> ################################################################# >> ##################################### >> done >> Bytes transferred = 4351908 (0x4267a4) >> Boot with zImage >> >> Starting kernel ... >> >> Uncompressing Linux... done, booting the kernel. >> Initializing cgroup subsys cpu >> Linux version 2.6.35.7 (liverpool@laptop-server) (gcc version 4.4.1 >> (Sourcery G++ Lite 2009q3-67) ) #1 PREEMPT Mon Apr 2 16:38:24 KST 2012 >> CPU: ARMv7 Processor [412fc082] revision 2 (ARMv7), cr=10c53c7f >> CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache >> Machine: MANGO210 >> Ignoring unrecognised tag 0x00000000 >> Ignoring unrecognised tag 0x00000000 >> Ignoring unrecognised tag 0x41001099 >> Memory policy: ECC disabled, Data cache writeback >> CPU S5PV210/S5PC110 (id 0x43110220) >> S3C24XX Clocks, Copyright 2004 Simtec Electronics >> S5PV210: PLL settings, A=1000000000, M=667000000, E=80000000 >> V=54000000 >> S5PV210: ARMCLK=1000000000, HCLKM=200000000, HCLKD=166750000 >> HCLKP=133400000, PCLKM=100000000, PCLKD=83375000, PCLKP=66700000 >> sclk_dmc: source is sclk_a2m (0), rate is 200000000 >> sclk_onenand: source is hclk_dsys (1), rate is 166750000 >> sclk: source is mout_mpll (6), rate is 66700000 >> sclk: source is mout_mpll (6), rate is 66700000 >> sclk: source is mout_mpll (6), rate is 66700000 >> sclk: source is mout_mpll (6), rate is 66700000 >> sclk_mixer: source is sclk_dac (0), rate is 54000000 >> sclk_spdif: source is sclk_audio (0), rate is 24000000 >> sclk_fimc: source is ext_xtal (0), rate is 24000000 >> sclk_fimc: source is ext_xtal (0), rate is 24000000 >> sclk_fimc: source is ext_xtal (0), rate is 24000000 >> sclk_cam0: source is ext_xtal (0), rate is 24000000 >> sclk_cam1: source is ext_xtal (0), rate is 24000000 >> sclk_fimd: source is ext_xtal (0), rate is 24000000 >> sclk_mmc: source is mout_mpll (6), rate is 47642857 >> sclk_mmc: source is mout_epll (7), rate is 80000000 >> sclk_mmc: source is mout_epll (7), rate is 80000000 >> sclk_mmc: source is mout_epll (7), rate is 80000000 >> sclk_mfc: source is sclk_a2m (0), rate is 200000000 >> sclk_g2d: source is sclk_a2m (0), rate is 200000000 >> sclk: source is sclk_a2m (0), rate is 200000000 >> sclk_csis: source is ext_xtal (0), rate is 24000000 >> sclk_spi: source is ext_xtal (0), rate is 24000000 >> sclk_spi: source is ext_xtal (0), rate is 24000000 >> sclk_pwi: source is ext_xtal (0), rate is 24000000 >> sclk_pwm: source is ext_xtal (0), rate is 24000000 >> sclk_mdnie: source is ext_xtal (0), rate is 24000000 >> sclk_mdnie_pwm: source is ext_xtal (0), rate is 24000000 >> s5pv210: 37748736 bytes system memory reserved for mfc at 0x20c6f000 >> s5pv210: 37748736 bytes system memory reserved for mfc at 0x40000000 >> s5pv210: 6144000 bytes system memory reserved for fimc0 at 0x42400000 >> s5pv210: 6144000 bytes system memory reserved for fimc1 at 0x429dc000 >> s5pv210: 6144000 bytes system memory reserved for fimc2 at 0x42fb8000 >> s5pv210: 6144000 bytes system memory reserved for jpeg at 0x43594000 >> s5pv210: 6144000 bytes system memory reserved for fimd at 0x43b70000 >> s5pv210: 1536000 bytes system memory reserved for texstream at >> 0x4414c000 >> s5pv210: 1536000 bytes system memory reserved for pmem_gpu1 at >> 0x442c3000 >> s5pv210: 6144000 bytes system memory reserved for g2d at 0x4443a000 >> Built 1 zonelists in Zone order, mobility grouping on. Total pages: >> 129536 >> Kernel command line: root=/dev/nfs rw nfsroot=192.168.0.100:/home/ >> liverpool/src/Gingerbread/PATCH.by_park/NFSROOT, nolock >> ip=192.168.0.111:192.168.0.100:192.168.0.254:255.255.255.0::eth0:off >> init=/init console=ttySAC1,115200 >> PID hash table entries: 2048 (order: 1, 8192 bytes) >> Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) >> Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) >> Memory: 256MB 256MB = 512MB total >> Memory: 398460k/398460k available, 125828k reserved, 0K highmem >> Virtual kernel memory layout: >> vector : 0xffff0000 - 0xffff1000 ( 4 kB) >> fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) >> DMA : 0xff000000 - 0xffe00000 ( 14 MB) >> vmalloc : 0xf0800000 - 0xfc000000 ( 184 MB) >> lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) >> modules : 0xbf000000 - 0xc0000000 ( 16 MB) >> .init : 0xc0008000 - 0xc002f000 ( 156 kB) >> .text : 0xc002f000 - 0xc0760000 (7364 kB) >> .data : 0xc0760000 - 0xc07a8660 ( 290 kB) >> SLUB: Genslabs=9, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 >> Hierarchical RCU implementation. >> RCU-based detection of stalled CPUs is disabled. >> Verbose stalled-CPUs detection is disabled. >> NR_IRQS:393 >> VIC @fd000000: id 0x00041192, vendor 0x41 >> VIC @fd010000: id 0x00041192, vendor 0x41 >> VIC @fd020000: id 0x00041192, vendor 0x41 >> VIC @fd030000: id 0x00041192, vendor 0x41 >> mult[140737] >> max_delta_ns[2937815369] >> min_delta_ns[30517] >> rate[32768] >> HZ[256] >> Console: colour dummy device 80x30 >> console [ttySAC1] enabled >> Calibrating delay loop... 998.15 BogoMIPS (lpj=1949696) >> pid_max: default: 32768 minimum: 301 >> Security Framework initialized >> SELinux: Initializing. >> Mount-cache hash table entries: 512 >> Initializing cgroup subsys debug >> Initializing cgroup subsys cpuacct >> Initializing cgroup subsys freezer >> CPU: Testing write buffer coherency: ok >> NET: Registered protocol family 16 >> S3C Power Management, Copyright 2004 Simtec Electronics >> pmstats at 00000000 >> mango210_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857 >> mango210_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857 >> mango210_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857 >> mango210_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857 >> S5PV210: Initializing architecture >> s3c24xx-pwm s3c24xx-pwm.0: tin at 66700000, tdiv at 66700000, >> tin=divclk, base 0 >> s3c24xx-pwm s3c24xx-pwm.1: tin at 66700000, tdiv at 66700000, >> tin=divclk, base 8 >> s3c24xx-pwm s3c24xx-pwm.2: tin at 66700000, tdiv at 66700000, >> tin=divclk, base 12 >> s3c24xx-pwm s3c24xx-pwm.3: tin at 66700000, tdiv at 66700000, >> tin=divclk, base 16 >> bio: create slab <bio-0> at 0 >> SCSI subsystem initialized >> usbcore: registered new interface driver usbfs >> usbcore: registered new interface driver hub >> usbcore: registered new device driver usb >> i2c-gpio i2c-gpio.0: using pins 40 (SDA) and 41 (SCL) >> i2c-gpio i2c-gpio.2: using pins 44 (SDA) and 45 (SCL) >> s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter >> Advanced Linux Sound Architecture Driver Version 1.0.23. >> Switching to clocksource clock_source_systimer >> NET: Registered protocol family 2 >> IP route cache hash table entries: 4096 (order: 2, 16384 bytes) >> TCP established hash table entries: 16384 (order: 5, 131072 bytes) >> TCP bind hash table entries: 16384 (order: 6, 327680 bytes) >> TCP: Hash tables configured (established 16384 bind 16384) >> TCP reno registered >> UDP hash table entries: 256 (order: 1, 12288 bytes) >> UDP-Lite hash table entries: 256 (order: 1, 12288 bytes) >> NET: Registered protocol family 1 >> RPC: Registered udp transport module. >> RPC: Registered tcp transport module. >> RPC: Registered tcp NFSv4.1 backchannel transport module. >> PMU: registered new PMU device of type 0 >> MANGO210 wifi init function >> MANGO210 RTC, (c) 2010 Samsung Electronics >> mango210-rtc mango210-rtc: rtc disabled, re-enabling >> mango210-rtc mango210-rtc: rtc core: registered s3c as rtc0 >> S5PV210 ADC driver, (c) 2010 Samsung Electronics >> cpuidle: phy_regs_save:0x4fd7e000 >> Loaded driver for PL330 DMAC-0 s3c-pl330 >> DBUFF-64x8bytes Num_Chans-8 Num_Peri-2 Num_Events-32 >> Loaded driver for PL330 DMAC-1 s3c-pl330 >> DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 >> Loaded driver for PL330 DMAC-2 s3c-pl330 >> DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 >> audit: initializing netlink socket (disabled) >> type=2000 audit(0.792:1): initialized >> ashmem: initialized >> msgmni has been set to 778 >> alg: No test for stdrng (krng) >> io scheduler noop registered >> io scheduler deadline registered >> io scheduler cfq registered (default) >> s3cfb s3cfb: [fb2] dma: 0x43b70000, cpu: 0xf1000000, size: 0x005dc000 >> FIMD src sclk = 166750000 >> s3cfb s3cfb: registered successfully >> Start display and show logo >> ipwireless 1.1 by Stephen Blackheath, Ben Martel, Jiri Kosina and >> David Sterba >> PA FB = 0x43B70000, bits per pixel = 32 >> screen width=800 height=480 va=0xe3b70000 pa=0x43b70000 >> xres_virtual = 800, yres_virtual = 1920, xoffset = 0, yoffset = 0 >> fb_size=6144000 >> Back frameBuffer[0].VAddr=e3ce7000 PAddr=43ce7000 size=1536000 >> Back frameBuffer[1].VAddr=e3e5e000 PAddr=43e5e000 size=1536000 >> Back frameBuffer[2].VAddr=e3fd5000 PAddr=43fd5000 size=1536000 >> s5pv210-uart.0: s3c2410_serial0 at MMIO 0xe2900000 (irq = 16) is a >> S3C6400/10 >> s5pv210-uart.1: s3c2410_serial1 at MMIO 0xe2900400 (irq = 20) is a >> S3C6400/10 >> s5pv210-uart.2: s3c2410_serial2 at MMIO 0xe2900800 (irq = 24) is a >> S3C6400/10 >> s5pv210-uart.3: s3c2410_serial3 at MMIO 0xe2900c00 (irq = 28) is a >> S3C6400/10 >> brd: module loaded >> loop: module loaded >> pmem_gpu1: 1 init >> Android kernel panic handler initialized (bind=kpanic) >> S3C NAND Driver, (c) 2008 Samsung Electronics >> S3C NAND Driver is using hardware ECC. >> NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB >> 3,3V 8-bit) >> Creating 6 MTD partitions on "s5pv210-nand": >> 0x000000000000-0x000000100000 : "bootloader" >> 0x000000100000-0x000000600000 : "recovery" >> 0x000000600000-0x000000b00000 : "kernel" >> 0x000000b00000-0x000000e00000 : "ramdisk" >> 0x000000e00000-0x000008600000 : "system" >> 0x000008600000-0x000010000000 : "userdata" >> PPP generic driver version 2.4.2 >> PPP Deflate Compression module registered >> PPP BSD Compression module registered >> smsc911x: Driver version 2008-10-21. >> smsc911x-mdio: probed >> eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, >> irq=-1) >> net eth0: MAC Address: 96:5b:9c:31:68:43 >> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver >> s5p-ehci s5p-ehci: s5pv210 EHCI >> s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1 >> s5p-ehci s5p-ehci: irq 87, io mem 0xec200000 >> s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00 >> hub 1-0:1.0: USB hub found >> hub 1-0:1.0: 1 port detected >> ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver >> s5p-ohci s5p-ohci: s5pv210 OHCI >> s5p-ohci s5p-ohci: new USB bus registered, assigned bus number 2 >> s5p-ohci s5p-ohci: irq 87, io mem 0xec300000 >> hub 2-0:1.0: USB hub found >> hub 2-0:1.0: 1 port detected >> Initializing USB Mass Storage driver... >> usbcore: registered new interface driver usb-storage >> USB Mass Storage support registered. >> s3c-udc : S3C HS USB Device Controller Driver, (c) 2008-2009 Samsung >> Electronics >> s3c-udc : version 15 March 2009 (DMA Mode) >> android init >> android_probe pdata: c076cf78 >> android_bind >> android_usb gadget: android_usb ready >> f_acm init >> android_register_function acm >> f_adb init >> android_register_function adb >> f_mass_storage init >> fsg_probe pdev: c076bdf0, pdata: c076cf9c >> android_register_function usb_mass_storage >> f_mtp init >> android_register_function mtp >> f_rndis init >> android_register_function rndis >> rndis_function_bind_config MAC: 00:00:00:00:00:00 >> android_usb gadget: using random self ethernet address >> android_usb gadget: using random host ethernet address >> usb0: MAC 9a:ee:1e:73:98:89 >> usb0: HOST MAC 92:4d:00:ca:f5:46 >> android_usb gadget: Mass Storage Function, version: 2009/09/11 >> android_usb gadget: Number of LUNs=1 >> lun0: LUN: removable file: (no medium) >> adb_bind_config >> mtp_bind_config >> mice: PS/2 mouse device common for all mice >> input: mango-keys as /devices/platform/mango-keys.0/input/input0 >> start MANGO GPIO Button V1.1 >> vd5376 0-0053: vd5376 initialization failed >> vd5376 2-0053: vd5376 initialization failed >> S5P Touchscreen driver, (c) 2008 Samsung Electronics >> S5P TouchScreen got loaded successfully : 12 bits >> input: S5P TouchScreen as /devices/virtual/input/input1 >> using rtc device, s3c, for alarms >> i2c /dev entries driver >> Linux video capture interface: v2.00 >> mfc_init: <6>S5PC110 MFC Driver, (c) 2009 Samsung Electronics >> S3C JPEG Driver, (c) 2007 Samsung Electronics >> JPEG driver for S5PV210 >> i2c i2c-1: attached s5p_ddc into i2c adapter successfully >> S5PC11X HPD Driver, (c) 2009 Samsung Electronics >> S5PC11X CEC Driver, (c) 2009 Samsung Electronics >> s3c_bat_init >> sec-fake-battery sec-fake-battery: s3c_bat_probe >> device-mapper: uevent: version 1.0.3 >> device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm- >> de...@redhat.com >> cpuidle: using governor ladder >> cpuidle: using governor menu >> sdhci: Secure Digital Host Controller Interface driver >> sdhci: Copyright(c) Pierre Ossman >> s3c-sdhci s3c-sdhci.3: clock source 0: hsmmc (133400000 Hz) >> s3c-sdhci s3c-sdhci.3: clock source 1: hsmmc (133400000 Hz) >> s3c-sdhci s3c-sdhci.3: clock source 2: sclk_mmc (47642857 Hz) >> mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.3] using ADMA >> s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133400000 Hz) >> s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133400000 Hz) >> s3c-sdhci s3c-sdhci.1: clock source 2: sclk_mmc (47642857 Hz) >> mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA >> s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133400000 Hz) >> s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133400000 Hz) >> s3c-sdhci s3c-sdhci.0: clock source 2: sclk_mmc (47642857 Hz) >> mmc2: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA >> s3c-sdhci s3c-sdhci.2: clock source 0: hsmmc (133400000 Hz) >> s3c-sdhci s3c-sdhci.2: clock source 1: hsmmc (133400000 Hz) >> s3c-sdhci s3c-sdhci.2: clock source 2: sclk_mmc (47642857 Hz) >> mmc3: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using ADMA >> usbcore: registered new interface driver usbhid >> usbhid: USB HID core driver >> logger: created 64K log 'log_main' >> logger: created 256K log 'log_events' >> logger: created 64K log 'log_radio' >> logger: created 64K log 'log_system' >> wm8960 0-001a: No platform data supplied >> android_usb gadget: high speed config #1: Android Composite >> mmc0: new high speed SDIO card at address 0001 >> s3c_idma_preallocate_buffer: VA-f08c0000 PA-C0000000 163840bytes >> asoc: WM8960 <-> s3c64xx-i2s mapping ok >> s3c_idma_preallocate_buffer: VA-f0900000 PA-C0000000 163840bytes >> asoc: WM8960 <-> s3c64xx-i2s mapping ok >> mmc2: new high speed SDHC card at address b368 >> mmcblk0: mmc2:b368 USD 7.46 GiB >> mmcblk0: p1 p2 p3 >> ASoC: Failed to create HP-L/R debugfs file >> ASoC: Failed to create Speaker-L/R debugfs file >> asoc: DIT <-> samsung-spdif mapping ok >> ALSA device list: >> #0: mango (WM8960) >> #1: SMDK (spdif-dit) >> Netfilter messages via NETLINK v0.30. >> nf_conntrack version 0.5.0 (6225 buckets, 24900 max) >> ip_tables: (C) 2000-2006 Netfilter Core Team >> arp_tables: (C) 2002 David S. Miller >> TCP cubic registered >> NET: Registered protocol family 17 >> Bridge firewalling registered >> Ebtables v2.0 registered >> ThumbEE CPU extension supported. >> VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev >> 2 >> mango210-rtc mango210-rtc: rtc disabled, re-enabling >> mango210-rtc mango210-rtc: setting system clock to 2011-01-01 12:00:02 >> UTC (1293883202) >> FIMC0 registered successfully >> FIMC1 registered successfully >> FIMC2 registered successfully >> <6>S5PC1XX TVOUT Driver, (c) 2009 Samsung Electronics >> s5p-tvout s5p-tvout: hpd status is cable removed >> [CRZ] SD/MMC channel 2 bus width : 1 >> [CRZ] sdhci_s3c_set_clock max_clock 47642857 >> [CRZ] SD/MMC channel 2 bus width : 1 >> [CRZ] SD/MMC channel 2 bus width : 1 >> net eth0: SMSC911x/921x identified at 0xf088e000, IRQ: 43 >> IP-Config: Complete: >> device=eth0, addr=192.168.0.111, mask=255.255.255.0, >> gw=192.168.0.254, >> host=192.168.0.111, domain=, nis-domain=(none), >> bootserver=192.168.0.100, rootserver=192.168.0.100, rootpath= >> DBUG_PORT must not use AFC! >> Looking up port of RPC 100003/2 on 192.168.0.100 >> Looking up port of RPC 100005/1 on 192.168.0.100 >> VFS: Mounted root (nfs filesystem) on device 0:14. >> Freeing init memory: 156K >> init: cannot open '/initlogo.rle' >> Kernel panic - not syncing: Attempted to kill init! >> Rebooting in 5 seconds..▒▒▒▒▒▒OK >> >> ------------------------------------------------------------------------------------ >> >> -- >> unsubscribe: android-kernel+unsubscr...@googlegroups.com >> website: http://groups.google.com/group/android-kernel > > > -- > unsubscribe: android-kernel+unsubscr...@googlegroups.com > website: http://groups.google.com/group/android-kernel > -- unsubscribe: android-kernel+unsubscr...@googlegroups.com website: http://groups.google.com/group/android-kernel
