@NEO:- I have USB port on my board ,but I can't use them like how I used on beagle board....they are normal USB port(to connect pandrive etc) same what we have on our PC. to connect the board we need a small usb port wheich is not on my board, as far as uart port is concerned...I do everything with the board through UART terminal.
@VAME:- Yes I tried to reconnect the device so many time...I am spending more than a week on this activity...both board and host pc are connected to the same network..and both are doing ping successfully... after #adb disconnect 107.108.175.19:5555 it is still able to ping.. to do ping i think it doesn't matter whom the device is connected to ,it only need to connect to network. and I tried all steps. when I do setprop service.adb.tcp.port 5555 it says *"could not set port*"..I dont understand why so...whereas When I do netcfg it showed all the things correct(IP address) start and stop adb binaries I dont have...we have limited binaries...I download all android binaries from net,but none of them is compatible with our kernel... Regards Manjeet On Tue, Dec 11, 2012 at 1:41 AM, vame <[email protected]> wrote: > Can you post logcat output from the device.? > Did you try reconnecting to the device? what is the ping status after* > * > #adb disconnect 107.108.175.19:5555 > No such device > > *Steps to connect your device to Host machine via Ethernet:* > On Device: > Step 1. Connect Ethernet cable and check if status > leds are blinking. > Step 2. Launch Android Terminal. > Step 3. Issue these commands: > # ifconfig eth0 <IP-address> up > # setprop service.adb.tcp.port 5555 > # stop adbd > # start adbd > On Host: > # adb connect <IP-address of device> > > With this you device should be connected. and by using > # adb shell > you are having access to the Android device shell. > > > On Tuesday, December 11, 2012 2:42:26 PM UTC+5:30, NEO SUN wrote: > >> I think, >> 1 you should use usb connect. Your board don't need OTG function, it is >> just a slave device. >> Please use usb cable. >> 2 If you want to use tcp connect, Please google it. >> http://ytydyd.blog.sohu.com/146260552.html >> it seems good. >> >> BTW: did you use uart console?Once i use uart console, i can not find >> device with adb devices. >> Maybe you need to disable uart console to make a test. >> >> >> 2012/12/11 Manjeet Pawar <[email protected]> >> >>> I have connected my board via ethernet port and have set an IP address . >>> I am able to ping successfully on both host and board..I checked for adbd >>> deamon on target ,initially it was not running , I started it by* * >>> *# adbd &* >>> Then I tried to connect it by giving following commands: >>> >>> # adb start-server >>> # adb connect 107.108.175.19:5555 >>> device connected successfully >>> #adb devices >>> No devices found >>> >>> or >>> >>> #adb disconnect 107.108.175.19:5555 >>> No such device >>> >>> *This is the error I am getting...I am confused if it is not connected >>> then why it showd connected when I use "adb connect " wheras adbd deamon >>> runs on board and IP address are set successfully.* >>> >>> >>> Thanks >>> Manjeet >>> >>> >>> On Mon, Dec 10, 2012 at 10:39 PM, NEO <[email protected]> wrote: >>> >>>> OTG? you need not to do this, just connect your board to your host pc. >>>> execute adb device, if your host pc has your device's adb drvier, adb >>>> will find your device. >>>> then run cts test. >>>> >>>> >>>> 2012/12/11 Manjeet Pawar <[email protected]> >>>> >>>>> I can use USB cable,bcoz I dont have OTG support on my board...only >>>>> things that i can use as a connection is "ethernet port"...but when i >>>>> followed the doc " >>>>> http://processors.wiki.ti.com/index.php/Android_ADB_Setup"...i didn't >>>>> have some binaries like setprop or su..I downloaded them,but they didn't >>>>> run properly.. >>>>> >>>>> Thanks >>>>> >>>>> On Mon, Dec 10, 2012 at 9:08 PM, NEO <[email protected]> wrote: >>>>> >>>>>> As you know, you need to fix the connection problem. >>>>>> Why don't you use usb cable? >>>>>> >>>>>> >>>>>> 2012/12/11 Manjeet Pawar <[email protected]> >>>>>> >>>>>>> *Hi All,* >>>>>>> >>>>>>> *I want to run CTS(compatibility Test Suite) from commandline. But >>>>>>> I am not able to connect my board thought ethernet port via 'adb'. So >>>>>>> connection between hostpc and my board(ARM board) is a measure issue >>>>>>> here...I have flashed android in my board still I am not able to >>>>>>> connect it >>>>>>> to the pc. Now I have to run CTS.How can I run CTS without adb >>>>>>> connection..?????? Because if there is no device connected to my pc,I >>>>>>> can't >>>>>>> start CTS on my host machine,so device must be connected..* >>>>>>> >>>>>>> *Has any one ever run CTS like this..????* >>>>>>> >>>>>>> *I have copied to complete source of Android CTS in to pandrive >>>>>>> which is accessible on board.But that seems to be impossible to run on >>>>>>> board, As 'startcts' used java to run itself, But we have dalvikVM on >>>>>>> android ,no jvm is there..how can I handle this..Please comments..* >>>>>>> >>>>>>> *Thanks & Regards* >>>>>>> *Manjeet Pawar* >>>>>>> -- >>>>>>> unsubscribe: [email protected] >>>>>>> website: http://groups.google.com/group/android-kernel >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> -- >>>>>> Best regards ! >>>>>> Mingting Sun >>>>>> -- >>>>>> unsubscribe: [email protected] >>>>>> website: http://groups.google.com/group/android-kernel >>>>> >>>>> >>>>> -- >>>>> unsubscribe: [email protected] >>>>> website: http://groups.google.com/group/android-kernel >>>> >>>> >>>> >>>> >>>> -- >>>> Best regards ! >>>> Mingting Sun >>>> -- >>>> unsubscribe: [email protected] >>>> website: http://groups.google.com/group/android-kernel >>>> >>> >>> -- >>> unsubscribe: [email protected] >>> website: http://groups.google.com/group/android-kernel >> >> >> >> >> -- >> Best regards ! >> Mingting Sun >> > -- > unsubscribe: [email protected] > website: http://groups.google.com/group/android-kernel > -- unsubscribe: [email protected] website: http://groups.google.com/group/android-kernel
