On Thu, Aug 4, 2011 at 3:03 PM, Alexander Hintzer <debia...@gmx.de> wrote: > > > Am 04.08.2011 14:33, schrieb Andrea Adami: >> >> On Thu, Aug 4, 2011 at 1:47 PM, Alexander Hintzer<debia...@gmx.de> wrote: >>> >>> >>> Am 04.08.2011 12:08, schrieb Andrea Adami: >>>> >>>> On Thu, Aug 4, 2011 at 11:51 AM, Alexander Hintzer<debia...@gmx.de> >>>> wrote: >>>>> >>>>> Hello all together. >>>>> >>>>> I am about to install Angstrom Linux on my Sharp Zaurus C1000. >>>>> I followed the instruction in the Wiki. So i formatted a 1GB SD Card >>>>> with >>>>> the ext2 file system >>>>> and then copied >>>>> >>>>> initrd.bin >>>>> updater.sh >>>>> zImage.bin >>>>> >>>>> from the Angstrom-x11-image-glibc-ipk-2007.12-r13-akita-installkit.tgz >>>>> archive to that partition on my SD Card.
Copy those three files, contained in http://projects.linuxtogo.org/frs/download.php/284/installkit-akita.tar.gz and flash the device. Once flashed, you can erase the SD card and untar the rootfs over it >>>>> >>>>> Next I followed the instructions to flash the Zaurus ROM. But this >>>>> fails >>>>> with a message on the screen that tells me that the SD Card could not >>>>> be >>>>> found. >>>>> >>>>> >>>>> I tried the same but instead formatted the SD Card with fat32. This >>>>> results >>>>> in a recognized SD Card by the Zaurus but ends with a messages saying >>>>> that >>>>> there is a syntax fault in updater.sh. >>>>> >>>>> Any suggestions? What am I doing wrong? >>>>> >>>>> _______________________________________________ >>>>> Angstrom-distro-devel mailing list >>>>> Angstrom-distro-devel@linuxtogo.org >>>>> >>>>> http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/angstrom-distro-devel >>>>> >>>> You are using outdated files (WIP). >>>> >>>> Download >>>> >>>> http://projects.linuxtogo.org/frs/download.php/284/installkit-akita.tar.gz >>>> then assemble one image for akita here: >>>> http://narcissus.angstrom-distribution.org/ >>>> >>>> (Optionally see instructions at >>>> http://kexecboot.org/documentation/how_to_write_config) >>>> >>>> Regards >>>> >>>> Andrea >>>> >>>> _______________________________________________ >>>> Angstrom-distro-devel mailing list >>>> Angstrom-distro-devel@linuxtogo.org >>>> >>>> http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/angstrom-distro-devel >>>> >>> >>> Hello and thank you for your reply. >>> >>> I did what you told me. So now i have downloaded installkit-akita.tar.gz >>> and >>> i assembled my own Image which comes in the >>> myZaurusImage-image-akita.tar.gz. >>> >>> But how to go on from here. The Manual >>> (http://www.linuxtogo.org/gowiki/AngstromManual) in the Wiki does not >>> describe how to install with the files you suggested me to use. >>> >>> Please give me a short explanation how to get it installed on my Zaurus. >>> >> >> Copy and untar it. (IMPORTANT: You must untar directly onto the SD/CF >> card. Do not untar somewhere else and then copy to the SD/CF): >> >> $ sudo cp Angstrom-akita-image.tar.gz /mnt/sda2 >> >> $ cd /mnt/sda2 >> $ sudo tar -xzpvf Angstrom-akita-image.tar.gz >> >> >> The rootfs already contains a kernel and a boot.cfg. >> >> Regards >> >> Andrea >> >>> Thank you! >>> >>> _______________________________________________ >>> Angstrom-distro-devel mailing list >>> Angstrom-distro-devel@linuxtogo.org >>> >>> http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/angstrom-distro-develfile >>> >> >> _______________________________________________ >> Angstrom-distro-devel mailing list >> Angstrom-distro-devel@linuxtogo.org >> http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/angstrom-distro-devel >> > > Ok, I unpacked Angstrom-akita-image.tar.gz to my SD Card (fat32). After that > there are the following folders on the Card: > > /media/3E50-8329$ ls > bin boot dev etc home lib media mnt proc sbin sys tmp usr var > > Then i did the usual steps to flash the ROM and got this message: see > attachment. > By the way: Before that i tried again with ext2 file system. And again the > Card was not detected successfully. > First flash then unpack the Narcissus image. The image can be extracted on a ext2/ext3/ext4 partition (and more) Regards Andrea > > > > > > _______________________________________________ > Angstrom-distro-devel mailing list > Angstrom-distro-devel@linuxtogo.org > http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/angstrom-distro-devel > > _______________________________________________ Angstrom-distro-devel mailing list Angstrom-distro-devel@linuxtogo.org http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/angstrom-distro-devel
