again i fail .
but someone can solve it .
i think micro SD in sd slot as CD , and micro SD in USB card reader as hard
disk .
--------------
# minicom -s
Welcome to minicom 2.7
OPTIONS: I18n
Compiled on Sep 6 2015, 19:49:19.
Port /dev/ttyUSB0, 11:52:24
Press CTRL-A Z for help on special keys
U-Boot 2017.03 (Apr 01 2017 - 04:27:09 -0600)
DRAM: 944 MiB
RPI 3 Model B (0xa02082)
MMC: bcm2835_sdhci: 0
reading uboot.env
** Unable to read "uboot.env" from mmc0:1 **
Using default environment
In: serial
Out: lcd
Err: lcd
Net: Net Initialization Skipped
No ethernet found.
starting USB...
USB0: Core Release: 2.80a
scanning bus 0 for devices...
USB device not accepting new address (error=0)
3 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
scanning usb for ethernet devices... 1 Ethernet Device(s) found
Hit any key to stop autoboot: 0
U-Boot> setenv boot_targets usb0 mmc0 pxe dhcp
U-Boot> saveenv
Saving Environment to FAT...
writing uboot.env
FAT: Misaligned buffer address (000000003ab2ab50)
sdhci_send_command: MMC: 0 busy timeout increasing to: 200 ms.
done
U-Boot> boot
USB device 0: unknown device
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found EFI removable media binary efi/boot/bootaa64.efi
reading efi/boot/bootaa64.efi
75737 bytes read in 68 ms (1.1 MiB/s)
## Starting EFI application at 01000000 ...
Scanning disks on usb...
Scanning disks on mmc...
MMC Device 1 not found
MMC Device 2 not found
MMC Device 3 not found
Found 5 disks
>> OpenBSD/arm64 BOOTAA64 0.2
boot>
booting sd0a:/bsd: 3735180+568620+500856+672776 [86+438216+232907]=0x7c2b70
[ using 672496 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2017 OpenBSD. All rights reserved.
https://www.OpenBSD.org
OpenBSD 6.1-current (GENERIC) #0: Thu Apr 6 22:45:47 AEST 2017
[email protected]:/usr/src/sys/arch/arm64/compile/GENERIC
real mem = 989855744 (944MB)
avail mem = 931606528 (888MB)
mainbus0 at root: Raspberry Pi 3 Model B Rev 1.2
simplefb0 at mainbus0: 656x416
wsdisplay0 at simplefb0 mux 1
wsdisplay0: screen 0 added (std, vt100 emulation)
simplebus0 at mainbus0: "soc"
bcmintc0 at simplebus0
bcmdog0 at simplebus0
pluart0 at simplebus0
com0 at simple�].�.r��6550, no workingcom0: console
dwctwo0 at simplebus0
agtimer0 at simplebus0: tick rate 19200 KHz
simplebus1 at mainbus0: "clocks"
usb0 at dwctwo0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Broadcom DWC2 root hub" rev
2.00/1.00 addr 1
uhub1 at uhub0 port 1 configuration 1 interface 0 "Standard Microsystems
product 0x9514" rev 2.00/2.2
smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems
SMSC9512/14" rev 2.00/2.00 3
smsc0: address b8:27:eb:c3:cc:1a
ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x0001f0, model 0x000c
umass0 at uhub1 port 2 configuration 1 interface 0 "Generic Mass Storage
Device" rev 2.00/1.00 addr 4
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <Multi, Flash Reader, 1.00> SCSI0 0/direct
removable serial.058f6366051
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
bootfile: sd0a:/bsd
boot device: sd0
panic: root device (22c292d19a866a8d) not found
Stopped at panic+0x158: TID PID UID PRFLAGS
PFLAGS C
PU COMMAND
* 0 0 0 0x10000 0x200 0 swapper
Debugger() at panic+0x154
panic() at diskconf+0xac
diskconf() at main+0x46c
main() at $x.2+0x70
https://www.openbsd.org/ddb.html describes the minimum info required in bug
reports. Insufficient info makes it difficult to find and fix bugs.
ddb>
-
regards
