Hi !
there is a very good reading at
http://www.undeadly.org/cgi?action=article&sid=20170409123528&mode=flat%20%EF%BF%BC
.
i only follow it .
sd card A USB card reader :Rpi3:micro sd card B in it's slot
at this state , i install openbsd into sd0 ( namely sd card A)
and reboot
at this state is the same
namely
sd card A USB card reader :Rpi3:micro sd card B in it's slot
but at boot
setenv boot_targets usb0 mmc0 pxe dhcp
saveenv
boot
-----------------
details is next
<power on>
minicom -s
Welcome to minicom 2.7
OPTIONS: I18n
Compiled on Sep 6 2015, 19:49:19.
Port /dev/ttyUSB0, 14:15:36
Press CTRL-A Z for help on special keys
U-Boot 2017.03 (Apr 01 2017 - 04:27:09 -0600)
DRAM: 944 MiB
RPI 3 Model B (0xa02082)
MMC: bcm2835_sdhci: 0
reading uboot.env
** Unable to read "uboot.env" from mmc0:1 **
Using default environment
In: serial
Out: lcd
Err: lcd
Net: Net Initialization Skipped
No ethernet found.
starting USB...
USB0: Core Release: 2.80a
scanning bus 0 for devices... 4 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 1 Ethernet Device(s) found
Hit any key to stop autoboot: 0
U-Boot> setenv boot_targets usb0 mmc0 pxe dhcp <---######################
U-Boot> saveenv <---######################
Saving Environment to FAT...
writing uboot.env
Error: Invalid FAT entry: 0xffffffe2
Invalid FAT entry
FAT: Misaligned buffer address (000000003ab2ab50)
sdhci_send_command: MMC: 0 busy timeout increasing to: 200 ms.
sdhci_send_command: MMC: 0 busy timeout increasing to: 400 ms.
done
U-Boot> boot <---######################
USB device 0:
Device 0: Vendor: MXT-USB Rev: 1308 Prod: Storage Device
Type: Removable Hard Disk
Capacity: 15343.0 MB = 14.9 GB (31422464 x 512)
... is now current device
Scanning usb 0:1...
Found EFI removable media binary efi/boot/bootaa64.efi
reading efi/boot/bootaa64.efi
75737 bytes read in 76 ms (972.7 KiB/s)
## Starting EFI application at 01000000 ...
Scanning disks on usb...
Scanning disks on mmc...
MMC Device 1 not found
MMC Device 2 not found
MMC Device 3 not found
Found 5 disks
>> OpenBSD/arm64 BOOTAA64 0.2
boot>
booting sd0a:/bsd: 3734688+568700+500888+672784 [86+438360+232975]=0x7c2c68
[ using 672704 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2017 OpenBSD. All rights reserved.
https://www.OpenBSD.org
OpenBSD 6.1 (GENERIC) #0: Sun Apr 2 17:05:03 AEST 2017
[email protected]:/usr/src/sys/arch/arm64/compile/GENERIC
real mem = 989855744 (944MB)
avail mem = 931606528 (888MB)
mainbus0 at root: Raspberry Pi 3 Model B Rev 1.2
simplefb0 at mainbus0: 656x416
wsdisplay0 at simplefb0 mux 1
wsdisplay0: screen 0 added (std, vt100 emulation)
simplebus0 at mainbus0: "soc"
bcmintc0 at simplebus0
bcmdog0 at simplebus0
pluart0 at simplebus0
com0 at simple�].�.r��6550, no workingcom0: console
dwctwo0 at simplebus0
agtimer0 at simplebus0: tick rate 19200 KHz
simplebus1 at mainbus0: "clocks"
usb0 at dwctwo0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Broadcom DWC2 root hub" rev
2.00/1.01
uhub1 at uhub0 port 1 configuration 1 interface 0 "Standard Microsystems
produc2
smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems
SMSC953
smsc0: address b8:27:eb:c3:cc:1a
ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x0001fc
umass0 at uhub1 port 2 configuration 1 interface 0 "MXTronics MXT USB
Device" r4
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <MXT-USB, Storage Device, 1308> SCSI0
0/direct ree
sd0: 15343MB, 512 bytes/sector, 31422464 sectors
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
bootfile: sd0a:/bsd
boot device: sd0
root on sd0a (a81499ded4c64177.a) swap on sd0b dump on sd0b
WARNING: /mnt was not properly unmounted
WARNING: CHECK AND RESET THE DATE!
Automatic boot in progress: starting file system checks.
/dev/sd0a (a81499ded4c64177.a): 1437 files, 21388 used, 223443 free (35
frags, )
/dev/sd0a (a81499ded4c64177.a): MARKING FILE SYSTEM CLEAN
/dev/sd0l (a81499ded4c64177.l): file system is clean; not checking
/dev/sd0d (a81499ded4c64177.d): file system is clean; not checking
/dev/sd0f (a81499ded4c64177.f): file system is clean; not checking
/dev/sd0g (a81499ded4c64177.g): file system is clean; not checking
/dev/sd0h (a81499ded4c64177.h): file system is clean; not checking
/dev/sd0k (a81499ded4c64177.k): file system is clean; not checking
/dev/sd0j (a81499ded4c64177.j): file system is clean; not checking
/dev/sd0e (a81499ded4c64177.e): file system is clean; not checking
setting tty flags
pf enabled
starting network
DHCPREQUEST on smsc0 to 255.255.255.255
DHCPACK from 192.168.80.1 (c8:3a:35:3b:c4:d0)
bound to 192.168.80.102 -- renewal in 43200 seconds.
reordering libraries:
done.
openssl: generating isakmpd/iked RSA keys... done.
ssh-keygen: generating new host keys: RSA DSA ECDSA ED25519
starting early daemons: syslogd pflogd ntpd.
starting RPC daemons:.
savecore: no core dump
checking quotas: done.
clearing /tmp
kern.securelevel: 0 -> 1
creating runtime link editor directory cache.
preserving editor files.
starting network daemons: sshd smtpd sndiod.
Path to firmware: http://firmware.openbsd.org/firmware/6.1/
No devices found which need firmware files to be downloaded.
starting local daemons: cron.
Sun Apr 2 16:26:36 JST 2017
OpenBSD/arm64 (foo.my.domain) (console)
login: root
Password:
OpenBSD 6.1 (GENERIC) #0: Sun Apr 2 17:05:03 AEST 2017
Welcome to OpenBSD: The proactively secure Unix-like operating system.
Please use the sendbug(1) utility to report bugs in the system.
Before reporting a bug, please try to reproduce it with the latest
version of the code. With bug reports, please try to ensure that
enough information to reproduce the problem is enclosed, and if a
known fix for it exists, include that as well.
You have new mail.
#
----------
regards
