Look in zttool or "head /proc/zaptel/[1-5] to see if the spans are in alarms. The leds on your boards might not lit properly.
regards Martin On Fri, 11 Jul 2003 [EMAIL PROTECTED] wrote: > yes, now i got the that problem solved, with 'immediate=yes', but now i've > faced with another, > When I connect the E1 to the cards, the LED lights does not change to green, > in E100P, its blinking red (even when there is no E1 plugged, its blinking > red) > and in E400P, its solid red. (this was the same even without > 'immediate=yes') > > When i start asterisk, the cards starts fine (as we see), givin the > following output, > *CLI> > == D-Channel on span 1 up > -- B-channel 1 successfully restarted on span 1 > -- B-channel 2 successfully restarted on span 1 > . . . > -- B-channel 31 successfully restarted on span 1 > > after i put 'immediate=yes', i can even call from outside to the PRI E1, and > get connected to asterisk, and listen to the prompts played by asterisk > > -- Accepting call from '062279955' to 's' on channel 1, span 1 > -- Executing Wait("Zap/1-1", "2") in new stack > -- Executing Answer("Zap/1-1", "") in new stack > -- Executing DigitTimeout("Zap/1-1", "5") in new stack > -- Set Digit Timeout to 5 > -- Executing ResponseTimeout("Zap/1-1", "10") in new stack > -- Set Response Timeout to 10 > -- Executing BackGround("Zap/1-1", "demo-congrats") in new stack > -- Playing 'demo-congrats' > > But calling to outside from asterisk fails (with the following errors), we > don't know whether this related to the above problem > > Executing Dial("SIP/802-8a26", "Zap/g2/0129063800|20|t") in new stack > NOTICE[262160]: File app_dial.c, Line 481 (dial_exec): Unable to create > channel of type 'Zap' > == Everyone is busy at this time > -- Executing Congestion("SIP/802-8a26", "") in new stack > == Spawn extension (sip, 980129063800, 2) exited non-zero on > 'SIP/802-8a26' > > Following are new zaptel and zapata conf files, > > zapata.conf > > [channels] > transfer=yes > echocancel=yes > callprogress=yes > immediate=yes > > ;E100p card > switchtype=EuroISDN > signalling=pri_cpe > pridialplan=unknown > context=inbound-pstn > group=2 > channel => 1-15,17-31 > > zaptel.conf > > > #E100p card > span=1,0,0,ccs,hdb3,crc4 > bchan=1-15,17-31 > dchan=16 > > defaultzone=us > loadzone=us > > > Thank you, > > Surajee > > ----- Original Message ----- > > From: "Cristi" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]> > Sent: Friday, July 11, 2003 10:39 PM > Subject: Re: [Asterisk-Users] ISDN PRI E1 configuration with E100P > > > > [EMAIL PROTECTED] wrote: > > > > > hi Everyone, > > > > > > We are configuring an ISDN PRI E1 with an E100P card, when you load > > > the drivers, and starts the asterisk, cards also starts fine, givin > > > following output, > > > > > > *CLI> > > > == D-Channel on span 1 up > > > -- B-channel 1 successfully restarted on span 1 > > > -- B-channel 2 successfully restarted on span 1 > > > . . . > > > -- B-channel 31 successfully restarted on span 1 > > > > > > but, when we make a call to this E1 from outside, it gives the > > > following error, > > > > > > WARNING[213006]: File chan_zap.c, Line 5248 (pri_fixup): Call > > > specified, but not found? > > > WARNING[213006]: File chan_zap.c, Line 5786 (pri_dchannel): Hangup on > > > bad channel 1 > > > WARNING[213006]: File chan_zap.c, Line 5248 (pri_fixup): Call > > > specified, but not found? > > > WARNING[213006]: File chan_zap.c, Line 5786 (pri_dchannel): Hangup on > > > bad channel 2 > > > > > > does anybody hav an idea on this? > > > > > > our zaptel.conf is, > > > > > > #E100p card > > > span=1,0,0,ccs,hdb3,crc4 > > > bchan=1-15,17-31 > > > dchan=16 > > > > > > zapata.conf, > > > > > > ;E100p card > > > switchtype=EuroISDN > > > signalling=pri_cpe > > > pridialplan=unknown > > > context=incoming > > > group = 2 > > > channel => 1-15,17-31 > > > > > > Thanks inadvance, > > > > > > Surajee > > > > > > > > > --------------This mail sent through OmniBIS.com-------------- > > > _______________________________________________ Asterisk-Users mailing > > > list [EMAIL PROTECTED] > > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > > I was having the same problem because : 1 number for E1 and the local > > PTSN was not sending the DID to select the appropriate extension. Set > > the immediate=yes into zapata.conf and catch the call into s extension! > > Thanks to Martin Pycko ... > > > > _______________________________________________ > > Asterisk-Users mailing list > > [EMAIL PROTECTED] > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > > > > > --------------This mail sent through OmniBIS.com-------------- > > _______________________________________________ > Asterisk-Users mailing list > [EMAIL PROTECTED] > http://lists.digium.com/mailman/listinfo/asterisk-users > _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users