hi all, i have now enabled pri debugging with "pri intense debug span"
so i get: -------------------- > Unnumbered frame: > SAPI: 00 C/R: 0 EA: 0 > TEI: 000 EA: 1 > M3: 3 P/F: 1 M2: 3 11: 3 [ SABME (set asynchronous balanced mode extended) ] > 0 bytes of data Urgent handler Sending Set Asynchronous Balanced Mode Extended -------------------- what does this all means ? best regards Wolfgang Am Mo, den 14.06.2004 schrieb Wolfgang Pichler um 14:06: > i've changed it now - but i still get the yellow alarm (i've changed it > to: span=1,1,0,ccs,hdb3,crc4,yellow) > > this is my dmesg output after ztcfg -v > ------------- > Found TE410P at base address 40100000, remapped to d8b15000 > TE410P version c01a009b > FALC version: 00000005, Board ID: 00 > Reg 0: 0x124b1800 > Reg 1: 0x124b1000 > Reg 2: 0x07fc07fc > Reg 3: 0x00000000 > Reg 4: 0x00000000 > Reg 5: 0x00000000 > Reg 6: 0xc01a009b > Reg 7: 0x00001f00 > Reg 8: 0x00000000 > Reg 9: 0x00ff0000 > Reg 10: 0x00000000 > TE410P: Launching card: 0 > TE410P: Setting up global serial parameters > Found a Wildcard: Wildcard TE410P-Xilinx > Registered tone zone 9 (Austria) > TE410P: Span 1 configured for CCS/HDB3/CRC4 > SPAN 1: Primary Sync Source > TE410P: Span 2 configured for CCS/HDB3/CRC4 > SPAN 2: Secondary Sync Source > wct4xxp: Setting yellow alarm on span 1 > wct4xxp: Setting yellow alarm on span 2 > ------------------- > > any other ideas ? > > best regards > Wolfgang > > Am Mo, den 14.06.2004 schrieb Jason Williams um 12:44: > > Wolfgang, > > > > You need to use ccs not cas > > > > > > I would change your timing options to these:- > > > > > > -------------/etc/zaptel.conf---------------- > > span=1,1,0,ccs,hdb3,crc4 > > span=2,2,0,ccs,hdb3,crc4 > > bchan=1-15 > > bchan=17-31 > > bchan=32-46 > > bchan=48-62 > > dchan=16 > > dchan=47 > > > > > > That should work > > > > > > At 12:33 14/06/2004 +0200, you wrote: > > >sorry, i don't know what you mean with: Is it the same as Telstra - > > >could you please clearify this ? > > > > > >wolfgang > > > > > >Am Mo, den 14.06.2004 schrieb Michael M. Saunders um 12:25: > > > > Is it the same as Telstra > > > > > > > > -----Original Message----- > > > > From: [EMAIL PROTECTED] > > > > [mailto:[EMAIL PROTECTED] On Behalf Of Wolfgang > > > > Pichler > > > > Sent: Monday, 14 June 2004 8:11 PM > > > > To: Asterisk-Users Mailinglist > > > > Subject: [Asterisk-Users] TE410P in Austria > > > > > > > > hi all, > > > > > > > > i've now installed a TE410P (Quad T1/E1 Primary Card - Digium) and > > > > connected it to a primary line. My telco (eTel) only told me that they > > > > are using hdb3 and crc4. So i still don't know which coding i have to > > > > use (cas or ccs) - and what timing options i have to use. > > > > > > > > Have someone already get a card like this up in Austria with a line from > > > > eTel or from the telekom Austria ? > > > > > > > > Another technics told me that it could be that i will need a different > > > > cable - could this be ? > > > > > > > > At time my configuration is: > > > > -------------/etc/zaptel.conf---------------- > > > > span=1,1,0,ccs,hdb3,crc4 > > > > span=2,1,0,ccs,hdb3,crc4 > > > > bchan=1-15 > > > > bchan=17-31 > > > > bchan=32-46 > > > > bchan=48-62 > > > > dchan=16 > > > > dchan=47 > > > > > > > > loadzone=at > > > > defaultzone=at > > > > > > > > -----------/etc/asterisk/zaptel.conf------------- > > > > [channels] > > > > switchtype = euroisdn > > > > signalling = pri_cpe > > > > pridialplan = local > > > > group = 1 > > > > context = default > > > > channel => 1-15 > > > > channel => 17-31 > > > > > > > > switchtype = euroisdn > > > > signalling = pri_cpe > > > > pridialplan = local > > > > group = 2 > > > > context=default > > > > channel => 32-46 > > > > channel => 48-62 > > > > > > > > Another thing - for the wct4xxp module - do i really need to restart the > > > > whole pc so that changes in /etc/zaptel.conf take effect, or do i only > > > > need to reinsert the module - rerun ztcfg ? > > > > > > > > hope someone here can help me > > > > > > > > best regards > > > > Wolfgang > > > > > > > > _______________________________________________ > > > > Asterisk-Users mailing list > > > > [EMAIL PROTECTED] > > > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > > To UNSUBSCRIBE or update options visit: > > > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > > > > > > > > > > _______________________________________________ > > > > Asterisk-Users mailing list > > > > [EMAIL PROTECTED] > > > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > > To UNSUBSCRIBE or update options visit: > > > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > > > >_______________________________________________ > > >Asterisk-Users mailing list > > >[EMAIL PROTECTED] > > >http://lists.digium.com/mailman/listinfo/asterisk-users > > >To UNSUBSCRIBE or update options visit: > > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > > _______________________________________________ > > Asterisk-Users mailing list > > [EMAIL PROTECTED] > > http://lists.digium.com/mailman/listinfo/asterisk-users > > To UNSUBSCRIBE or update options visit: > > http://lists.digium.com/mailman/listinfo/asterisk-users > > _______________________________________________ > Asterisk-Users mailing list > [EMAIL PROTECTED] > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
