Hi all, I have an ath5k device in my laptop (a toshiba A305); I am running kernel 2.6.27-rc6:
[ 231.899321] ath5k_pci 0000:06:00.0: enabling device (0000 -> 0002) [ 231.901148] ath5k_pci 0000:06:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 231.903348] ath5k_pci 0000:06:00.0: setting latency timer to 64 [ 231.905365] ath5k_pci 0000:06:00.0: registered as 'phy0' [ 231.911840] ath5k phy0: Support for RF2425 is under development. [ 231.950692] PM: Adding info for No Bus:phy0 [ 231.952760] PM: Adding info for No Bus:wmaster0 [ 231.954614] phy0: Selected rate control algorithm 'pid' [ 232.002244] PM: Adding info for No Bus:wlan0 [ 232.005649] ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY: 0x70) It normally works ok with both my dynamic-wep work configuration and wep home one, under NetworkManager. But sometime after resume it happens the following: [ 3843.040068] evdev.c(EVIOCGBIT): Suspicious buffer size 511, limiting output to 64 bytes. See http://userweb.kernel.org/~dtor/eviocgbit-bug.html [ 3853.887794] ath5k phy0: noise floor calibration failed (2437MHz) [ 3853.889748] ath5k phy0: can't reset hardware (-11) [ 3853.891259] wlan0: Failed to config new SSID to the low-level driver [ 3853.914507] ath5k phy0: noise floor calibration failed (2437MHz) [ 3853.914521] ath5k phy0: ath5k_chan_set: unable to reset channel (2412 Mhz) [ 3853.914525] wlan0: failed to restore operational channel after scan [ 3854.250186] ath5k phy0: gain calibration timeout (2437MHz) [ 3854.250198] ath5k phy0: can't reset hardware (-11) [ 3854.250202] wlan0: Failed to config new BSSID to the low-level driver and so on and on. Nothing seems to resume the card, only a reboot; rmmod-ing and reloading the ath5k modules has no effects: [ 3943.600078] PM: Removing info for No Bus:wlan0 [ 3943.614012] PM: Removing info for No Bus:wmaster0 [ 3943.621735] PM: Removing info for No Bus:phy0 [ 3943.622496] ath5k_pci 0000:06:00.0: PCI INT A disabled [ 3953.954495] ath5k_pci 0000:06:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 3953.954542] ath5k_pci 0000:06:00.0: setting latency timer to 64 [ 3953.954614] ath5k_pci 0000:06:00.0: registered as 'phy1' [ 3953.959144] __ratelimit: 15 callbacks suppressed [ 3953.959151] ath5k phy1: Support for RF2425 is under development. [ 3953.998768] PM: Adding info for No Bus:phy1 [ 3954.002174] PM: Adding info for No Bus:wmaster0 [ 3954.003599] phy1: Selected rate control algorithm 'pid' [ 3954.003904] PM: Adding info for No Bus:wlan0 [ 3954.005386] ath5k phy1: Atheros AR2425 chip found (MAC: 0xe2, PHY: 0x70) [ 3954.417959] ath5k phy1: gain calibration timeout (2412MHz) [ 3954.419628] ath5k phy1: unable to reset hardware: -11 is this a known problem? Can I help debugging something? Thanks! Romano -- La presente comunicación tiene carácter confidencial y es para el exclusivo uso del destinatario indicado en la misma. Si Ud. no es el destinatario indicado, le informamos que cualquier forma de distribución, reproducción o uso de esta comunicación y/o de la información contenida en la misma están estrictamente prohibidos por la ley. Si Ud. ha recibido esta comunicación por error, por favor, notifíquelo inmediatamente al remitente contestando a este mensaje y proceda a continuación a destruirlo. Gracias por su colaboración. This communication contains confidential information. It is for the exclusive use of the intended addressee. If you are not the intended addressee, please note that any form of distribution, copying or use of this communication or the information in it is strictly prohibited by law. If you have received this communication in error, please immediately notify the sender by reply e-mail and destroy this message. Thank you for your cooperation. _______________________________________________ ath5k-devel mailing list ath5k-devel@lists.ath5k.org https://lists.ath5k.org/mailman/listinfo/ath5k-devel
