Hi , We have WIFI (atheros) and SATA(sil3114), are connected with DM6467T Host . The PCI arbiter logic is also used for sharing the bus. We are able to enumerate all the PCI devices from the Host.
I have installed the WIFI driver (Madwif -HAL driver). But I could not able communicate via WIFI. If do scan, it is giving like "wifi0: ath_chan_set: Unable to reset channel 9 (2452 MHz) flags 0xc0 'Hardware didn't respond as expected' (HAL status 3). Pls find the logs below .......... r...@172.22.66.12:~# uname -r 2.6.32-rc2-davinci1 r...@172.22.66.12:~# lspci 00:05.0 Mass storage controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid ] Serial ATA Controller (rev 02) 00:06.0 Ethernet controller: Atheros Communications, Inc. AR5006X 802.11abg NIC (rev 01) r...@172.22.66.12:~# lspci -x 00:05.0 Mass storage controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid ] Serial ATA Controller (rev 02) 00: 95 10 14 31 47 01 b0 02 02 00 80 01 08 00 00 00 10: 11 00 00 4a 21 00 00 4a 19 00 00 4a 25 00 00 4a 20: 01 00 00 4a 00 00 09 30 00 00 00 00 95 10 14 31 30: 00 00 00 00 60 00 00 00 00 00 00 00 30 01 00 00 00:06.0 Ethernet controller: Atheros Communications, Inc. AR5006X 802.11abg NIC (rev 01) 00: 8c 16 1b 00 40 03 90 02 01 00 00 02 08 00 00 00 10: 00 00 08 30 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 01 50 00 00 5f 18 00 16 30: 00 00 00 00 44 00 00 00 00 00 00 00 31 01 0a 1c r...@172.22.66.12:~# lspci -v 00:05.0 Mass storage controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid ] Serial ATA Controller (rev 02) Subsystem: Silicon Image, Inc. SiI 3114 SATALink Controller Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 48 I/O ports at 4a000010 [size=8] I/O ports at 4a000020 [size=4] I/O ports at 4a000018 [size=8] I/O ports at 4a000024 [size=4] I/O ports at 4a000000 [size=16] Memory at 30090000 (32-bit, non-prefetchable) [size=1K] [virtual] Expansion ROM at 30000000 [disabled] [size=512K] Capabilities: [60] Power Management version 2 00:06.0 Ethernet controller: Atheros Communications, Inc. AR5006X 802.11abg NIC (rev 01) Subsystem: Wistron NeWeb Corp. DCMA-82 High Power WLAN 802.11a/b/g mini- PCI Module (Super A/G, eXtended Range, 400mW) Flags: fast Back2Back, medium devsel, IRQ 49 Memory at 30080000 (32-bit, non-prefetchable) [disabled] [size=64K] Capabilities: [44] Power Management version 2 r...@172.22.66.12:~# cd /home/raghu/HAL/wifi/wifi_modules/ r...@172.22.66.12:/home/raghu/HAL/wifi/wifi_modules# ./install.sh ath_hal: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133, RF2425, RF2417, REGOPS_FUNC) wlan: mac acl policy registered in function __pci_register_driver PCI: enabling device 0000:00:06.0 (0340 -> 0342) MadWifi: ath_attach: Switching rfkill capability off. wifi0: Atheros AR5414 chip found (MAC 10.5, PHY SChip 6.1, Radio 6.3) ath_pci: wifi0: Atheros 5413: mem=0x30080000, irq=49 in function __pci_register_driver after driver reg in function __pci_register_driver after pci_create_newid_file in function __pci_register_driver after pci_create_removeid_file r...@172.22.66.12:/home/raghu/HAL/wifi/wifi_modules# r...@172.22.66.12:/home/raghu/HAL/wifi/wifi_modules# iwconfig iwconfig: Symbol `iw_operation_mode' has different size in shared objectnet eth0 : DaVinci EMAC: ioctl not supported , consider re-linking lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. wlan0 IEEE 802.11b ESSID:"" Nickname:"" Mode:Managed Channel:0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:0 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=0/70 Signal level=0 dBm Noise level=0 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 r...@172.22.66.12:/home/raghu/HAL/wifi/wifi_modules# ifconfig eth0 Link encap:Ethernet HWaddr 00:0E:99:02:B5:67 inet addr:172.22.66.12 Bcast:172.22.79.255 Mask:255.255.240.0 inet6 addr: fe80::20e:99ff:fe02:b567/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15390 errors:0 dropped:0 overruns:0 frame:0 TX packets:6572 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:10004560 (9.5 MiB) TX bytes:1090732 (1.0 MiB) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:560 (560.0 b) TX bytes:560 (560.0 b) r...@172.22.66.12:/home/raghu/HAL/wifi/wifi_modules# ifconfig wlan0 up r...@172.22.66.12:/home/raghu/HAL/wifi/wifi_modules# cd .. r...@172.22.66.12:/home/raghu/HAL/wifi# cd wifi_apps/ r...@172.22.66.12:/home/raghu/HAL/wifi/wifi_apps# ./wlanconfig wlan0 list scann r...@172.22.66.12:/home/raghu/HAL/wifi/wifi_apps# wifi0: ath_chan_set: Unable to reset channel 6 (2437 MHz) flags 0xc0 'Hardware didn't respond as expected' (HA L status 3) ./wlanconfig wlan0 list scannwifi0: ath_chan_set: Unable to reset channel 7 (244 2 MHz) flags 0xc0 'Hardware didn't respond as expected' (HAL status 3) wifi0: ath_chan_set: Unable to reset channel 56 (5280 MHz) flags 0x140 'Hardware didn't respond as expected' (HAL status 3) wifi0: ath_chan_set: Unable to reset channel 64 (5320 MHz) flags 0x140 'Hardware didn't respond as expected' (HAL status 3) wifi0: ath_chan_set: Unable to reset channel 40 (5200 MHz) flags 0x140 'Hardware didn't respond as expected' (HAL status 3) wifi0: ath_chan_set: Unable to reset channel 48 (5240 MHz) flags 0x140 'Hardware didn't respond as expected' (HAL status 3) wifi0: ath_chan_set: Unable to reset channel 3 (2422 MHz) flags 0xc0 'Hardware d idn't respond as expected' (HAL status 3) wifi0: ath_chan_set: Unable to reset channel 5 (2432 MHz) flags 0xc0 'Hardware d idn't respond as expected' (HAL status 3) wifi0: ath_chan_set: Unable to reset channel 9 (2452 MHz) flags 0xc0 'Hardware d idn't respond as expected' (HAL status 3) wifi0: ath_chan_set: Unable to reset channel 149 (5745 MHz) flags 0x140 'Hardwar e didn't respond as expected' (HAL status 3) wifi0: ath_chan_set: Unable to reset channel 157 (5785 MHz) flags 0x140 'Hardwar e didn't respond as expected' (HAL status 3) wifi0: ath_chan_set: Unable to reset channel 165 (5825 MHz) flags 0x140 'Hardwar e didn't respond as expected' (HAL status 3) wifi0: ath_chan_set: Unable to reset channel 50 (5250 MHz) flags 0x150 'Hardware didn't respond as expected' (HAL status 3) wifi0: ath_chan_set: Unable to reset channel 152 (5760 MHz) flags 0x150 'Hardwar e didn't respond as expected' (HAL status 3) wifi0: ath_chan_set: Unable to reset channel 40 (5200 MHz) flags 0x140 'Hardware didn't respond as expected' (HAL status 3) wifi0: ath_chan_set: Unable to reset channel 56 (5280 MHz) flags 0x140 'Hardware didn't respond as expected' (HAL status 3) wifi0: ath_chan_set: Unable to reset channel 161 (5805 MHz) flags 0x140 'Hardwar e didn't respond as expected' (HAL status 3) wifi0: ath_chan_set: Unable to reset channel 1 (2412 MHz) flags 0xc0 'Hardware d idn't respond as expected' (HAL status 3) wifi0: ath_chan_set: Unable to reset channel 7 (2442 MHz) flags 0xc0 'Hardware d idn't respond as expected' (HAL status 3) wifi0: ath_chan_set: Unable to reset channel 56 (5280 MHz) flags 0x140 'Hardware didn't respond as expected' (HAL status 3) wifi0: ath_chan_set: Unable to reset channel 64 (5320 MHz) flags 0x140 'Hardware didn't respond as expected' (HAL status 3) Thanks & Regards, Raghu Ramaraj ________________________________ http://www.mindtree.com/email/disclaimer.html
_______________________________________________ ath5k-devel mailing list ath5k-devel@lists.ath5k.org https://lists.ath5k.org/mailman/listinfo/ath5k-devel