Got you on the script front. My issue is slightly different, when I get into my magic state, pressing the power button does nothing.
On Wednesday, December 2, 2015 at 3:51:42 PM UTC-8, William Hermans wrote: > > >> *In my case linux is not booted at this time(none of the 4 user leds >> lit), so a script would not help. This is why I'm doing an external >> watchdog circuit.* > > > Exactly. So here is what I mean. The USR LEDs cycle on for me *if* and > only *if* I press the power button on the board. After that, nothing > changes. Otherwise the LEDs are off, well the power LED is on, and the > ethernet port lights are on too, and potentially blinking. > > The script, would just be to reboot the board in an attempt to put the > board back into the bad state. For troubleshooting . . . > > On Wed, Dec 2, 2015 at 4:46 PM, Jonathan Ross <jon...@nephology.org > <javascript:>> wrote: > >> In my case linux is not booted at this time(none of the 4 user leds lit), >> so a script would not help. This is why I'm doing an external watchdog >> circuit. >> >> On Wednesday, December 2, 2015 at 3:41:32 PM UTC-8, William Hermans wrote: >>> >>> *I didn't test the 8 second holddown of the power button but I doubt it >>>> would help, and unfortunately it's not a reproducible issue. I'll have to >>>> wait for it to happen again.* >>>> >>> >>> I know what you mean, e.g. this happens so erratically, it's hard to >>> tell when it'll happen next. But, I could possibly whip up a script, and a >>> means to automate resetting the system. Really, you could probably do the >>> same as well. Just put "sudo reboot" in a bash script, and run it through >>> rc.d >>> >>> With that said, I'm not 100% sure this is good for the board. >>> >>> >>> >>> On Wed, Dec 2, 2015 at 4:31 PM, Jonathan Ross <jon...@nephology.org> >>> wrote: >>> >>>> I didn't test the 8 second holddown of the power button but I doubt it >>>> would help, and unfortunately it's not a reproducible issue. I'll have to >>>> wait for it to happen again. >>>> From my notes, I was seeing zero volts on power, 5V on reset. >>>> The zero volts on power was very weird. From the KL16 I'm "toggling" my >>>> own effective power button that is a transistor between the power pin on >>>> the header and ground. The KL16 pin was not driven high (I checked), so I >>>> don't think it was the transistor on the cape that was pulling pwr to >>>> ground on the BBB. And the physical button wasn't pressed in. It was as if >>>> the pullup at the PMIC wasn't active, yet the power LED was on. Is that >>>> possible? >>>> Wish I hadn't pulled the 5V power to reset, then I could do more >>>> testing. >>>> >>>> On Wednesday, December 2, 2015 at 2:11:58 PM UTC-8, Gerald wrote: >>>>> >>>>> I would start with your cape design and try and rule that out first. >>>>> >>>>> The reset is an input pin read by the processor, not actually a HW >>>>> power reset. If the SW is locked up, this could happen. >>>>> >>>>> If you hold the power button for a 8 seconds or more the board should >>>>> power cycle. >>>>> >>>>> When it is in this state, what do the voltages read? >>>>> >>>>> Gerald >>>>> >>>>> >>>>> On Wed, Dec 2, 2015 at 3:54 PM, Jonathan Ross <jon...@nephology.org> >>>>> wrote: >>>>> >>>>>> Once in a blue moon one of my beaglebones will get into a state where >>>>>> it has power (the power LED is lit), but it is not booted. Normally this >>>>>> would be fine, just hit the power button to reset. But in this weird >>>>>> state >>>>>> the power button does nothing. The reset button does nothing. >>>>>> I checked the power and reset button pins on the header, the power >>>>>> was low, the reset was high. >>>>>> The only way to get the board out of this state was to pull the 5V >>>>>> power. >>>>>> I'm using a KL16 on a cape to do a watchdog on the BB, and reboot it >>>>>> via power and/or reset buttons on the header if the BB stops sending >>>>>> checkins over uart. This has been working great, except for the rare >>>>>> case >>>>>> where the board ends up in this state where the power and reset buttons >>>>>> are >>>>>> not functioning. >>>>>> Any ideas how the BB could get into this state, and if there's any >>>>>> other way to force a reboot other than physically pulling the 5v power? >>>>>> Thanks, >>>>>> JR >>>>>> >>>>>> -- >>>>>> For more options, visit http://beagleboard.org/discuss >>>>>> --- >>>>>> You received this message because you are subscribed to the Google >>>>>> Groups "BeagleBoard" group. >>>>>> To unsubscribe from this group and stop receiving emails from it, >>>>>> send an email to beagleboard...@googlegroups.com. >>>>>> For more options, visit https://groups.google.com/d/optout. >>>>>> >>>>> >>>>> >>>>> >>>>> -- >>>>> Gerald >>>>> >>>>> ger...@beagleboard.org >>>>> http://beagleboard.org/ >>>>> >>>> -- >>>> For more options, visit http://beagleboard.org/discuss >>>> --- >>>> You received this message because you are subscribed to the Google >>>> Groups "BeagleBoard" group. >>>> To unsubscribe from this group and stop receiving emails from it, send >>>> an email to beagleboard...@googlegroups.com. >>>> For more options, visit https://groups.google.com/d/optout. >>>> >>> >>> -- >> For more options, visit http://beagleboard.org/discuss >> --- >> You received this message because you are subscribed to the Google Groups >> "BeagleBoard" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to beagleboard...@googlegroups.com <javascript:>. >> For more options, visit https://groups.google.com/d/optout. >> > > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to beagleboard+unsubscr...@googlegroups.com. For more options, visit https://groups.google.com/d/optout.