I am using 200 MHz ADC clock frequency (demux-1). And I am not sure how to check the adc repo and mlib_devel repo versions ? Could you please help me in that ? Thank you.
On Wed, Mar 29, 2017 at 6:39 PM, Jack Hickish <[email protected]> wrote: > I like the triumphant "done!" at the end :) > > Next questions -- > What version of the adc repo and mlib_devel repos are you using? > Do you have other hardware you can test on? (It's very unlikely to be a > hardware problem, IMO, but worth checking if you can). > What ADC clock rate are you using? > > Cheers > Jack > > On Wed, 29 Mar 2017 at 14:39 vijay kumar <[email protected]> > wrote: > >> Yes ! I assume the clock has been clocked. For convenience, I have >> included the output script i get after I run the initialization script. >> >> >> Programming 192.168.10.2 with direct_mar_29_2017_Mar_29_1500.bof.gz... >> Design built for ROACH2 rev2 with 4 ADCs (ZDOK rev2) >> Gateware supports demux modes (using demux by 1) >> Resetting ADC, power cycling ADC, and reprogramming FPGA... >> ZDOK0 clock OK >> Calibrating SERDES blocks...calibrating chips ["A", "B", "C", "D"] >> chip A chan 1 lane 0 no good taps found >> chip A chan 1 lane 1 no good taps found >> chip A chan 2 lane 0 no good taps found >> chip A chan 2 lane 1 no good taps found >> chip A chan 3 lane 0 no good taps found >> chip A chan 3 lane 1 no good taps found >> chip A chan 4 lane 0 no good taps found >> chip A chan 4 lane 1 no good taps found >> chip B chan 1 lane 0 no good taps found >> chip B chan 1 lane 1 no good taps found >> chip B chan 2 lane 0 no good taps found >> chip B chan 2 lane 1 no good taps found >> chip B chan 3 lane 0 no good taps found >> chip B chan 3 lane 1 no good taps found >> chip B chan 4 lane 0 no good taps found >> chip B chan 4 lane 1 no good taps found >> chip C chan 1 lane 0 no good taps found >> chip C chan 1 lane 1 no good taps found >> chip C chan 2 lane 0 no good taps found >> chip C chan 2 lane 1 no good taps found >> chip C chan 3 lane 0 no good taps found >> chip C chan 3 lane 1 no good taps found >> chip C chan 4 lane 0 no good taps found >> chip C chan 4 lane 1 no good taps found >> chip D chan 1 lane 0 no good taps found >> chip D chan 1 lane 1 no good taps found >> chip D chan 2 lane 0 no good taps found >> chip D chan 2 lane 1 no good taps found >> chip D chan 3 lane 0 no good taps found >> chip D chan 3 lane 1 no good taps found >> chip D chan 4 lane 0 no good taps found >> chip D chan 4 lane 1 no good taps found >> >> ERROR: SERDES calibration failed for ADC A. >> ERROR: SERDES calibration failed for ADC B. >> ERROR: SERDES calibration failed for ADC C. >> ERROR: SERDES calibration failed for ADC D. >> Selecting analog inputs... >> Using default digital gain of 1... >> Done! >> >> >> On Wed, Mar 29, 2017 at 5:33 PM, Jack Hickish <[email protected]> >> wrote: >> >> Further, is the board clocking OK? -- I believe the initialization script >> should give feedback on whether of not the FPGA's PLL has successfully >> locked to the ADC clock, and what the current measured board clock is. >> >> Cheers >> Jack >> >> On Wed, 29 Mar 2017 at 14:28 Matt Dexter <[email protected]> wrote: >> >> Is the design and lab setup consistent with the limitations documented at >> https://casper.berkeley.edu/wiki/ADC16x250-8#ADC16_Sample_ >> Rate_vs_Virtex-6_MMCM_Limitations >> ? >> >> More information on the clock requirements may be found at >> https://casper.berkeley.edu/wiki/ADC16x250-8_coax_rev_2# >> ADC16x250-8_coax_rev_2_Inputs >> >> Matt >> >> On Wed, 29 Mar 2017, vijay kumar wrote: >> >> > Date: Wed, 29 Mar 2017 17:16:34 -0400 >> > From: vijay kumar <[email protected]> >> > To: [email protected] >> > Subject: [casper] ADC calibration issue >> > >> > Hello Casperites, >> > I have been working on the ROACH-2 casper for the past few months. Now >> i have started to capture values from the ADC >> > 16x250-8 block. But, when I am trying to run the initialization script, >> it gives me an error saying that "chip 'x' >> > chan 'x' lane 'x' no good taps found ". I am unable to figure out what >> might be causing this error. I would be glad >> > if I could get help from you guys. >> > >> > Thank you. >> > >> > >> > With regards >> > Vijay >> > >> > -- >> > You received this message because you are subscribed to the Google >> Groups "[email protected]" group. >> > To unsubscribe from this group and stop receiving emails from it, send >> an email to >> > [email protected]. >> > To post to this group, send email to [email protected]. >> > >> > >> >> -- >> You received this message because you are subscribed to the Google Groups >> "[email protected]" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> To post to this group, send email to [email protected]. >> >> -- >> You received this message because you are subscribed to the Google Groups >> "[email protected]" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> To post to this group, send email to [email protected]. >> >> >> -- You received this message because you are subscribed to the Google Groups "[email protected]" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To post to this group, send email to [email protected].

