The following is output I get when i type the 'git rev-parse HEAD':

a949c9d5c1761078b4c884699ff52c1497a17ff6

On Thu, Mar 30, 2017 at 2:32 PM, Mark Wagner <[email protected]> wrote:

> git rev-parse HEAD
>
> On Thu, Mar 30, 2017 at 10:46 AM, Jack Hickish <[email protected]>
> wrote:
>
>> Someone better with git can tell you the "right" way, but I would just
>> run "git log" in the repository directory, and note the most recent commit
>> hash.
>>
>> Cheers
>> Jack
>>
>> On Thu, 30 Mar 2017 at 10:31 vijay kumar <[email protected]>
>> wrote:
>>
>>> I am using 200 MHz ADC clock frequency (demux-1). And I am not sure how
>>> to check the adc repo and mlib_devel repo versions ? Could you please help
>>> me in that ?
>>> Thank you.
>>>
>>> On Wed, Mar 29, 2017 at 6:39 PM, Jack Hickish <[email protected]>
>>> wrote:
>>>
>>> I like the triumphant "done!" at the end :)
>>>
>>> Next questions --
>>> What version of the adc repo and mlib_devel repos are you using?
>>> Do you have other hardware you can test on? (It's very unlikely to be a
>>> hardware problem, IMO, but worth checking if you can).
>>> What ADC clock rate are you using?
>>>
>>> Cheers
>>> Jack
>>>
>>> On Wed, 29 Mar 2017 at 14:39 vijay kumar <[email protected]>
>>> wrote:
>>>
>>> Yes ! I assume the clock has been clocked. For convenience, I have
>>> included the output script i get after I run the initialization script.
>>>
>>>
>>> Programming 192.168.10.2 with direct_mar_29_2017_Mar_29_1500.bof.gz...
>>> Design built for ROACH2 rev2 with 4 ADCs (ZDOK rev2)
>>> Gateware supports demux modes (using demux by 1)
>>> Resetting ADC, power cycling ADC, and reprogramming FPGA...
>>> ZDOK0 clock OK
>>> Calibrating SERDES blocks...calibrating chips ["A", "B", "C", "D"]
>>> chip A chan 1 lane 0 no good taps found
>>> chip A chan 1 lane 1 no good taps found
>>> chip A chan 2 lane 0 no good taps found
>>> chip A chan 2 lane 1 no good taps found
>>> chip A chan 3 lane 0 no good taps found
>>> chip A chan 3 lane 1 no good taps found
>>> chip A chan 4 lane 0 no good taps found
>>> chip A chan 4 lane 1 no good taps found
>>> chip B chan 1 lane 0 no good taps found
>>> chip B chan 1 lane 1 no good taps found
>>> chip B chan 2 lane 0 no good taps found
>>> chip B chan 2 lane 1 no good taps found
>>> chip B chan 3 lane 0 no good taps found
>>> chip B chan 3 lane 1 no good taps found
>>> chip B chan 4 lane 0 no good taps found
>>> chip B chan 4 lane 1 no good taps found
>>> chip C chan 1 lane 0 no good taps found
>>> chip C chan 1 lane 1 no good taps found
>>> chip C chan 2 lane 0 no good taps found
>>> chip C chan 2 lane 1 no good taps found
>>> chip C chan 3 lane 0 no good taps found
>>> chip C chan 3 lane 1 no good taps found
>>> chip C chan 4 lane 0 no good taps found
>>> chip C chan 4 lane 1 no good taps found
>>> chip D chan 1 lane 0 no good taps found
>>> chip D chan 1 lane 1 no good taps found
>>> chip D chan 2 lane 0 no good taps found
>>> chip D chan 2 lane 1 no good taps found
>>> chip D chan 3 lane 0 no good taps found
>>> chip D chan 3 lane 1 no good taps found
>>> chip D chan 4 lane 0 no good taps found
>>> chip D chan 4 lane 1 no good taps found
>>>
>>> ERROR: SERDES calibration failed for ADC A.
>>> ERROR: SERDES calibration failed for ADC B.
>>> ERROR: SERDES calibration failed for ADC C.
>>> ERROR: SERDES calibration failed for ADC D.
>>> Selecting analog inputs...
>>> Using default digital gain of 1...
>>> Done!
>>>
>>>
>>> On Wed, Mar 29, 2017 at 5:33 PM, Jack Hickish <[email protected]>
>>> wrote:
>>>
>>> Further, is the board clocking OK? -- I believe the initialization
>>> script should give feedback on whether of not the FPGA's PLL has
>>> successfully locked to the ADC clock, and what the current measured board
>>> clock is.
>>>
>>> Cheers
>>> Jack
>>>
>>> On Wed, 29 Mar 2017 at 14:28 Matt Dexter <[email protected]> wrote:
>>>
>>> Is the design and lab setup consistent with the limitations documented at
>>> https://casper.berkeley.edu/wiki/ADC16x250-8#ADC16_Sample_Ra
>>> te_vs_Virtex-6_MMCM_Limitations
>>> ?
>>>
>>> More information on the clock requirements may be found at
>>> https://casper.berkeley.edu/wiki/ADC16x250-8_coax_rev_2#ADC1
>>> 6x250-8_coax_rev_2_Inputs
>>>
>>> Matt
>>>
>>> On Wed, 29 Mar 2017, vijay kumar wrote:
>>>
>>> > Date: Wed, 29 Mar 2017 17:16:34 -0400
>>> > From: vijay kumar <[email protected]>
>>> > To: [email protected]
>>> > Subject: [casper] ADC calibration issue
>>> >
>>> > Hello Casperites,
>>> > I have been working on the ROACH-2 casper for the past few months. Now
>>> i have started to capture values from the ADC
>>> > 16x250-8 block. But, when I am trying to run the initialization
>>> script, it gives me an error saying that "chip 'x'
>>> > chan 'x' lane 'x' no good taps found  ". I am unable to figure out
>>> what might be causing this error. I would be glad
>>> > if I could get help from you guys.
>>> >
>>> > Thank you.
>>> >
>>> >
>>> > With regards
>>> > Vijay
>>> >
>>> > --
>>> > You received this message because you are subscribed to the Google
>>> Groups "[email protected]" group.
>>> > To unsubscribe from this group and stop receiving emails from it, send
>>> an email to
>>> > [email protected].
>>> > To post to this group, send email to [email protected].
>>> >
>>> >
>>>
>>> --
>>> You received this message because you are subscribed to the Google
>>> Groups "[email protected]" group.
>>> To unsubscribe from this group and stop receiving emails from it, send
>>> an email to [email protected].
>>> To post to this group, send email to [email protected].
>>>
>>> --
>>> You received this message because you are subscribed to the Google
>>> Groups "[email protected]" group.
>>> To unsubscribe from this group and stop receiving emails from it, send
>>> an email to [email protected].
>>> To post to this group, send email to [email protected].
>>>
>>>
>>>
>>> --
>> You received this message because you are subscribed to the Google Groups
>> "[email protected]" group.
>> To unsubscribe from this group and stop receiving emails from it, send an
>> email to [email protected].
>> To post to this group, send email to [email protected].
>>
>
>

-- 
You received this message because you are subscribed to the Google Groups 
"[email protected]" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to [email protected].
To post to this group, send email to [email protected].

Reply via email to