Hi Mark

The current SKARAB 40G yellowblock is a bit of a hack. 

  1) It is currently not parameterised, and is hard-coded for the first port on 
Mezzanine slot 3. 

  2) The tx_valid and rx_valid lines are 4-bits wide, not 1 bit. This will be 
rectified soon, but in the meanwhile, just feed the value "3" to tx_valid to 
send packets.

  3) Note that there was a recent change to the TX and RX 64-bit word ordering 
(was previously incorrectly swapped). Make you built your bitstreams with a 
recent git checkout.

It's on our todo list to get it properly parameterised and to fix the 4-bit 
weirdness, but it's not clear when we'll have that done.  In the meanwhile, the 
40G does work, and we are successfully using this first port actively at SKA-SA.

Some things you should try to help debug:

  1) The microblaze will attempt to DHCP on the 40G interface. Did it obtain a 
lease? Check your DHCP server logs.

  2) Check (using casperfpga software) that the cores are actually configured 
like you think. There was a version of microblaze that overwrote things. And if 
it's DHCP'ing (this is how we use the ports), then the IP will have changed 
from what you expect. 
myfpgaobject.gbes['my_forty_gbe_core'].print_core_details() (or 
g.get_core_details()).

  3) What does tcpdump/wireshark show is coming out of the TX board? 

  4) Did you select different MAC addresses for the "hardcoded" yellowblocks on 
the TX and RX side? Else a switch might not forward the packets.

  5) Can you ping both 40G interfaces from a computer?

Jason Manley
CBF Manager
SKA-SA

Cell: +27 82 662 7726
Work: +27 21 506 7300

On 29 Jun 2017, at 20:37, Peryer, Mark A. <[email protected]> wrote:

> Hello,
> 
> I am trying to send data from one SKARAB to another SKARAB over 40GbE. I have 
> created two separate JASPER files, one for receiving and one for 
> transmitting. Each design has one forty_gbe yellow block and are configured 
> similar to Tutorial 2 on the casper website. In the JASPER file used for 
> transmitting, I have placed a snapshot block on the tx_data signal for the 
> forty_gbe block and am able to read the correct data from the snapshot block 
> using casperfpga. While it appears that the correct data is being 
> transmitted, nothing is received by the second SKARAB. In the JASPER file 
> used for receiving data, I have a snapshot block on the rx_data signal, which 
> should trigger once a valid frame is received. However, when I run 
> fpga01.snapshots.snapshot2.print_snap(50) it just hangs, indicating nothing 
> has been received. 
> 
> I did notice that when I right click on the forty_gbe yellow block and go to 
> Mask >> Edit Mask >> Parameters&Dialog, there is a menu that allows for the 
> card slot location of the 40GbE card to be selected. Our SKARAB units have 
> the 40GbE card populated on Mezzanine Slot 3, however only Card Slot 0 and 1 
> are available to be selected. Should this option be set to slot 3 in order to 
> properly use the 40GbE ports?
> 
> I should also mention that I have configured the tx_dest_ip block input to be 
> 192.168.5.20 and the tx_dest_port to be 10000, which are the default values 
> for the forty_gbe block.
> 
> If there is anything else I should look at in order to properly configure the 
> forty_gbe yellow blocks please advise.
> 
> Thanks,
> 
> Mark
> 
>   
> 
> -- 
> You received this message because you are subscribed to the Google Groups 
> "[email protected]" group.
> To unsubscribe from this group and stop receiving emails from it, send an 
> email to [email protected].
> To post to this group, send email to [email protected].

-- 
You received this message because you are subscribed to the Google Groups 
"[email protected]" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to [email protected].
To post to this group, send email to [email protected].

Reply via email to