Morning Mark

Please have a look here for SKARAB 40gbe TX and RX models with demo
software.

https://github.com/ska-sa/mkat_fpga/tree/devel/source/skarab_dev/tut2

Cheers
Paul


On 30 June 2017 at 07:46, Jason Manley <[email protected]> wrote:

> Hi Mark
>
> The current SKARAB 40G yellowblock is a bit of a hack.
>
>   1) It is currently not parameterised, and is hard-coded for the first
> port on Mezzanine slot 3.
>
>   2) The tx_valid and rx_valid lines are 4-bits wide, not 1 bit. This will
> be rectified soon, but in the meanwhile, just feed the value "3" to
> tx_valid to send packets.
>
>   3) Note that there was a recent change to the TX and RX 64-bit word
> ordering (was previously incorrectly swapped). Make you built your
> bitstreams with a recent git checkout.
>
> It's on our todo list to get it properly parameterised and to fix the
> 4-bit weirdness, but it's not clear when we'll have that done.  In the
> meanwhile, the 40G does work, and we are successfully using this first port
> actively at SKA-SA.
>
> Some things you should try to help debug:
>
>   1) The microblaze will attempt to DHCP on the 40G interface. Did it
> obtain a lease? Check your DHCP server logs.
>
>   2) Check (using casperfpga software) that the cores are actually
> configured like you think. There was a version of microblaze that overwrote
> things. And if it's DHCP'ing (this is how we use the ports), then the IP
> will have changed from what you expect. myfpgaobject.gbes['my_forty_
> gbe_core'].print_core_details() (or g.get_core_details()).
>
>   3) What does tcpdump/wireshark show is coming out of the TX board?
>
>   4) Did you select different MAC addresses for the "hardcoded"
> yellowblocks on the TX and RX side? Else a switch might not forward the
> packets.
>
>   5) Can you ping both 40G interfaces from a computer?
>
> Jason Manley
> CBF Manager
> SKA-SA
>
> Cell: +27 82 662 7726
> Work: +27 21 506 7300
>
> On 29 Jun 2017, at 20:37, Peryer, Mark A. <[email protected]>
> wrote:
>
> > Hello,
> >
> > I am trying to send data from one SKARAB to another SKARAB over 40GbE. I
> have created two separate JASPER files, one for receiving and one for
> transmitting. Each design has one forty_gbe yellow block and are configured
> similar to Tutorial 2 on the casper website. In the JASPER file used for
> transmitting, I have placed a snapshot block on the tx_data signal for the
> forty_gbe block and am able to read the correct data from the snapshot
> block using casperfpga. While it appears that the correct data is being
> transmitted, nothing is received by the second SKARAB. In the JASPER file
> used for receiving data, I have a snapshot block on the rx_data signal,
> which should trigger once a valid frame is received. However, when I run
> fpga01.snapshots.snapshot2.print_snap(50) it just hangs, indicating
> nothing has been received.
> >
> > I did notice that when I right click on the forty_gbe yellow block and
> go to Mask >> Edit Mask >> Parameters&Dialog, there is a menu that allows
> for the card slot location of the 40GbE card to be selected. Our SKARAB
> units have the 40GbE card populated on Mezzanine Slot 3, however only Card
> Slot 0 and 1 are available to be selected. Should this option be set to
> slot 3 in order to properly use the 40GbE ports?
> >
> > I should also mention that I have configured the tx_dest_ip block input
> to be 192.168.5.20 and the tx_dest_port to be 10000, which are the default
> values for the forty_gbe block.
> >
> > If there is anything else I should look at in order to properly
> configure the forty_gbe yellow blocks please advise.
> >
> > Thanks,
> >
> > Mark
> >
> >
> >
> > --
> > You received this message because you are subscribed to the Google
> Groups "[email protected]" group.
> > To unsubscribe from this group and stop receiving emails from it, send
> an email to [email protected].
> > To post to this group, send email to [email protected].
>
> --
> You received this message because you are subscribed to the Google Groups "
> [email protected]" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to [email protected].
> To post to this group, send email to [email protected].
>

-- 
You received this message because you are subscribed to the Google Groups 
"[email protected]" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to [email protected].
To post to this group, send email to [email protected].

Reply via email to