Hi Xavier,

At 2.5GHz sampling frequency you might need to calibrate each IO lane
individually, rather than just sweeping the global clock phase. I don't
know where you're getting your calibration code from, but if you have a
calibrate_all_delays method (like at
https://github.com/jack-h/adc_tests/blob/disentangle/adc5g/src/tools.py)
you might want to try using that and see if you have any luck.

Cheers
Jack

PS. I think harmonizing (and robustifying) adc link training code is going
to be pretty high on the CASPER development priorities, and I'm sure will
be discussed at the workshop in a couple of weeks.

On Fri, 28 Jul 2017 at 05:06 Xavier Bosch <[email protected]>
wrote:

> Hi Jonathan,
> Thank you for your response.
> Unfortunately, I only have one ADC, so I cannot discern between hardware
> and software error testing each ADC separately.
> Yes, it is an ROACH2. At the Simulink level, I deleted the ZDOK_1 ADC and
> I removed some Simulink block that was related to simulation (a block that
> was reporting data in the workspace) because Matlab was crashing when
> compiling. These are all the modifications that I did at the CASPER design
> with respect  the one provided in
> https://github.com/sma-wideband/adc_tests
>
> thank you,
> XB
>
>
>
> On Thu, Jul 27, 2017 at 6:02 PM Jonathan Weintroub <
> [email protected]> wrote:
>
>> Hi Xavier,
>>
>> One obvious question is do you really have just one ADC board?  Or have
>> you seen the same results on more than one hardware set?
>>
>> Also, where you say: "I adapted the CASPER design to match my hardware .
>> . .” could you give a little more detail on what hardware you are using?
>> Is this based on a ROACH2?
>>
>> Thanks,
>>
>> Jonathan
>>
>>
>> On Jul 27, 2017, at 8:02 PM, Xavier Bosch <[email protected]>
>> wrote:
>>
>> Hi all,
>>
>> I got a ADC 5G V2.0 DMUX1:1 and I decided to evaluate its performance. As
>> expected the results are poor and its phase needs to be calibrated. I read
>> the document in here
>> http://www.worldscientific.com/doi/pdf/10.1142/S2251171714500019  and I
>> got code from here  https://github.com/sma-wideband/adc_tests I adapted
>> the CASPER design to match my hardware and I also adapted the calibration
>> routines.
>>
>> The result is always the same: while setting the ADC in test mode,
>> channels *a, b, c* report 0 glitches while the channel *d* reports about
>> ~2000 out of the 16384 samples each time. I sweep the phase using the c
>> *alibrate_mmcm_phase()* function but I never got to reduce the number of
>> glitches.So the optimal phase does not exist, hence it cannot be
>> calibrated.
>>
>> I am attaching two histograms for ADC_fs=2,5GHz and a signal of input
>> power fo -10 dBm and 1 MHz and 800 MHz respectively. As you can see,*
>> a,b,c* channels are withing a reasonable margin while channel *d *gets
>> out of control.
>>
>> Has anyone find a problem like that before? How have you solved? Is there
>> more available documentation for that part ?
>>
>> Thank you,
>>
>> XB
>>
>>
>> --
>> You received this message because you are subscribed to the Google Groups
>> "[email protected]" group.
>> To unsubscribe from this group and stop receiving emails from it, send an
>> email to [email protected].
>> To post to this group, send email to [email protected].
>> <HistogramTest_800MHz_m10dBm_sampling2p5GHz.png>
>> <HistogramTest_1MHz_m10dBm_sampling2p5GHz.png>
>>
>> --
> You received this message because you are subscribed to the Google Groups "
> [email protected]" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to [email protected].
> To post to this group, send email to [email protected].
>

-- 
You received this message because you are subscribed to the Google Groups 
"[email protected]" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to [email protected].
To post to this group, send email to [email protected].

Reply via email to