If you are studying for the V4 exam, the equipment will be all Cisco 3560s. Typically the lab workbooks from both IPExpert and INE use 4 switches. You'll want the Advanced IP Services image to run (at least 12.2 (25) I believe). I think this image requires either 128 mb to run. You'll see two types listed : PS which is Power of Ethernet, and TS which is not. If you are planning to study for the VOIP track later, you might want to go ahead and make sure you buy a PoE capable switch; otherwise, don't worry about that too much. You probably will want the 24 port models although you might be able to get away with modifying the labs to use 8 ports.
With dynamips, you have a couple ways to connect the switches. You can either buy enough nics (think: quad nic cards) to have a separate connection from the PC to each switchport; or, if you have a single nic gig card that is capable of dot1q trunking, you can buy a fifth switch to use as a breakout switch. This is what I did and so far it works pretty well. Hope this information helps. Michael 2009/6/10 MANNY Omari <[email protected]> > > > > Hello Michael, > > I hope you are doing well. Thank you very much for the advice, will you > pleaser advice which model Switch do i need to buy? > can please provide me full specification of the switch i will try to get > used one from ebay. > > Best Regards > Manouchehr > > > ------------------------------ > Date: Wed, 10 Jun 2009 05:42:16 -0400 > Subject: Re: [OSL | CCIE_RS] Dynamips > From: [email protected] > To: [email protected] > CC: [email protected]; [email protected] > > > MANNY, > You cannot do a full lab with just dynamips - the NM-16ESW cannot emulate > the full functionality of the 3550/3560 switches; however, you should be > able to practice all the routing topics and supplement with rack time if > your budget doesn't allow you to buy the 4 switches you'll need. > > My study lab is a combination of dynamips and four switches which I prefer, > but it is still expensive to do it this way. It probably is cheaper to buy > rack time but I wanted to be able to do any study topic at any time. > > Michael > > 2009/6/10 MANNY Omari <[email protected]> > > > > Hello Sir, > > > Thank you very much great work, I have one question Do I need physical > hardware (Router/Switch) to fully with Dynamips or i can do all with > Dynamips for the CCIE R&S v4? > > > Best Regards > > Manouchehr > CCNP - CCNA > > > > > From: [email protected] > > To: [email protected]; [email protected] > > Date: Wed, 10 Jun 2009 00:17:52 -0400 > > Subject: [OSL | CCIE_RS] Dynamips > > > > Hey Guys, > > > > After some feedback and since I was in a OWLE today and couldn’t work on > > labs or my main project work I used my spare time today to Go over the > > Dynamips I had handed out before. I did some further testing and I was > > incorrect in having two NM-16ESW’s in one chassis so I am attaching my > new > > .net file that I used today. > > > > I found that I was able to get it work with about 1.6GB of Memory and you > > can probably run the full topology with a dual core. It may be a little > > sluggish. But with a Quad Core it really hums away. > > > > Here is the full .net file. I will also be uploading it to the > > Configuration Group For OSL. I have already uploaded updated diagrams to > > the R&S section for this. My formatting is a little screwed up below but > it > > should be good. > > > > If you use the exact image I have shown below the IDLE PC values will > work > > as shown below. If not you will need to re-calculate the IDLE-PC Values > > This was run on Fedora Core 10 x64 edition. > > > > A few recommendations when running the topology. > > > > 1. If possible, only do a SINGLE trunk between routers with the 16 port > > ethernet modules. Dynamips has a really hard time and can set itself into > > broadcast storms when there are multiple. If you have to do multiple, you > > should enable ALL ports on every device. If you have one side enabled and > > the other shutdown, it's almost a sure loop once you start creating your > > VLANs > > > > 2. Don't start more than three router instances at a time - then let them > > finish booting and let your CPU return to normal > > > > 3. Create all your access ports, and THEN add the config under "vlan dat" > > - this helps minimize broadcast storms. > > > > 4. Delete your files from your working directory AND recycle bin after > each > > dynamips session. > > > > > > #============================================================== > > # > > # NAME: IPexpert_Dynamips_RS-SP.net > > # CONTRIBUTORS: > > # Tyson Scott ([email protected]) > > # DATE : 06/09/2009 > > # PURPOSE: Define Virtual Network Topology for CCIE Training > > # REQUIREMENTS: Dynamips and Dynagen or GNS3. > > # > > #============================================================== > > > > > > # *** Either Set the autstart to *** > > # False - Do not start each device automatically > > # True - Start Each device upon hypervisor Execution > > autostart = False > > > > ############################### > > # # > > # First Hypervisor # > > # # > > ############################### > > > > [localhost:7201] > > # > > # Uncomment the appropriate Line for the Operating system you are > > running > > # *** Windows Working Directory *** > > #workingdir = C:\DYNAMIPS\Working > > # > > # *** Linux Working Directory *** > > workingdir = /home/tyson/DYNAMIPS/Working/ > > # > > udp = 10100 > > > > [[3725]] > > # > > # Uncomment the appropriate Line for the Operating system you > > are running > > #*** Windows IMAGE PATH *** > > #image = > > C:\DYNAMIPS\IMAGES\c3725-adventerprisek9-mz.124-15.T9.bin.unpacked > > # > > #*** Linux IMAGE PATH *** > > image = > > > /home/tyson/DYNAMIPS/IMAGES/c3725-adventerprisek9-mz.124-15.T9.bin.unpacked > > # > > ram = 256 > > > > [[ROUTER R1]] > > model = 3725 > > console = 2001 > > autostart = False > > ghostios = true > > sparsemem = true > > # > > idlepc = 0x62b200d8 > > #idlepc = 0x62b200dc > > #idlepc = 0x60c0aa58 > > #idlepc = 0x614ab010 > > #idlepc = 0x614ab070 > > #idlepc = 0x614ab0b8 > > #idlepc = 0x614ab0cc > > #idlepc = 0x6026b438 > > #idlepc = 0x62b1c780 > > #idlepc = 0x60c05010 > > #*** Windows Configuration PATH *** > > #cnfg = C:\DYNAMIPS\Startup_Configs\R1.txt > > # > > #*** Linux Configuration PATH *** > > cnfg = /home/tyson/DYNAMIPS/Startup_Configs/R1.txt > > f0/0 = Cat1 f1/1 > > f0/1 = Cat2 f1/1 > > > > [[ROUTER R2]] > > model = 3725 > > console = 2002 > > autostart = False > > ghostios = true > > sparsemem = true > > #idlepc = 0x62b200d8 > > #idlepc = 0x62b200dc > > idlepc = 0x60c0aa58 > > #idlepc = 0x614ab010 > > #idlepc = 0x614ab070 > > #idlepc = 0x614ab0b8 > > #idlepc = 0x614ab0cc > > #idlepc = 0x6026b438 > > #idlepc = 0x62b1c780 > > #idlepc = 0x60c05010 > > #*** Windows Configuration PATH *** > > #cnfg = C:\DYNAMIPS\Startup_Configs\R2.txt > > # > > #*** Linux Configuration PATH *** > > cnfg = /home/tyson/DYNAMIPS/Startup_Configs/R2.txt > > s0/1 = FR-Switch 2 > > s0/2 = R5 s0/2 > > slot1 = NM-16ESW > > f1/0 = Cat1 f1/2 > > f1/1 = Cat3 f1/2 > > > > [[ROUTER R4]] > > model = 3725 > > console = 2004 > > autostart = False > > ghostios = true > > sparsemem = true > > #idlepc = 0x62b200d8 > > #idlepc = 0x62b200dc > > #idlepc = 0x60c0aa58 > > #idlepc = 0x614ab010 > > idlepc = 0x614ab070 > > #idlepc = 0x614ab0b8 > > #idlepc = 0x614ab0cc > > #idlepc = 0x6026b438 > > #idlepc = 0x62b1c780 > > #idlepc = 0x60c05010 > > #*** Windows Configuration PATH *** > > #cnfg = C:\DYNAMIPS\Startup_Configs\R4.txt > > # > > #*** Linux Configuration PATH *** > > cnfg = /home/tyson/DYNAMIPS/Startup_Configs/R4.txt > > s0/1 = FR-Switch 4 > > f0/0 = Cat1 f1/4 > > f0/1 = Cat3 f1/4 > > > > [[ROUTER R5]] > > model = 3725 > > console = 2005 > > autostart = False > > ghostios = true > > sparsemem = true > > #idlepc = 0x62b200d8 > > #idlepc = 0x62b200dc > > #idlepc = 0x60c0aa58 > > idlepc = 0x614ab010 > > #idlepc = 0x614ab070 > > #idlepc = 0x614ab0b8 > > #idlepc = 0x614ab0cc > > #idlepc = 0x6026b438 > > #idlepc = 0x62b1c780 > > #idlepc = 0x60c05010 > > #*** Windows Configuration PATH *** > > #cnfg = C:\DYNAMIPS\Startup_Configs\R5.txt > > # > > #*** Linux Configuration PATH *** > > cnfg = /home/tyson/DYNAMIPS/Startup_Configs/R5.txt > > s0/1 = FR-Switch 5 > > s0/2 = R2 s0/2 > > f0/0 = Cat1 f1/5 > > f0/1 = Cat3 f1/5 > > > > ############################### > > # # > > # Second Hypervisor # > > # # > > ############################### > > > > [localhost:7202] > > # > > # Uncomment the appropriate Line for the Operating system you are > > running > > # *** Windows Working Directory *** > > #workingdir = C:\DYNAMIPS\Working > > # > > # *** Linux Working Directory *** > > workingdir = /home/tyson/DYNAMIPS/Working/ > > # > > udp = 10200 > > > > [[3725]] > > # > > # Uncomment the appropriate Line for the Operating system you > > are running > > #*** Windows IMAGE PATH *** > > #image = > > C:\DYNAMIPS\IMAGES\c3725-adventerprisek9-mz.124-15.T9.bin.unpacked > > # > > #*** Linux IMAGE PATH *** > > image = > > > /home/tyson/DYNAMIPS/IMAGES/c3725-adventerprisek9-mz.124-15.T9.bin.unpacked > > # > > ram = 256 > > > > [[ROUTER R6]] > > model = 3725 > > console = 2006 > > autostart = False > > ghostios = true > > sparsemem = true > > #idlepc = 0x62b200d8 > > #idlepc = 0x62b200dc > > #idlepc = 0x60c0aa58 > > #idlepc = 0x614ab010 > > #idlepc = 0x614ab070 > > #idlepc = 0x614ab0b8 > > idlepc = 0x614ab0cc > > #idlepc = 0x6026b438 > > #idlepc = 0x62b1c780 > > #idlepc = 0x60c05010 > > #*** Windows Configuration PATH *** > > #cnfg = C:\DYNAMIPS\Startup_Configs\R6.txt > > # > > #*** Linux Configuration PATH *** > > cnfg = /home/tyson/DYNAMIPS/Startup_Configs/R6.txt > > s0/1 = FR-Switch 6 > > f0/0 = Cat2 f1/6 > > f0/1 = Cat4 f1/6 > > slot2 = NM-4T > > s2/0 = R9 s2/0 > > s2/1 = R9 s2/1 > > > > [[ROUTER R7]] > > model = 3725 > > console = 2007 > > autostart = False > > ghostios = true > > sparsemem = true > > #idlepc = 0x62b200d8 > > #idlepc = 0x62b200dc > > #idlepc = 0x60c0aa58 > > #idlepc = 0x614ab010 > > #idlepc = 0x614ab070 > > #idlepc = 0x614ab0b8 > > #idlepc = 0x614ab0cc > > idlepc = 0x6026b438 > > #idlepc = 0x62b1c780 > > #idlepc = 0x60c05010 > > #*** Windows Configuration PATH *** > > #cnfg = C:\DYNAMIPS\Startup_Configs\R7.txt > > # > > #*** Linux Configuration PATH *** > > cnfg = /home/tyson/DYNAMIPS/Startup_Configs/R7.txt > > s0/0 = R8 s0/0 > > f0/0 = Cat2 f1/7 > > f0/1 = Cat4 f1/7 > > > > [[ROUTER R8]] > > model = 3725 > > console = 2008 > > autostart = False > > ghostios = true > > sparsemem = true > > idlepc = 0x62b200d8 > > #idlepc = 0x62b200dc > > #idlepc = 0x60c0aa58 > > #idlepc = 0x614ab010 > > #idlepc = 0x614ab070 > > #idlepc = 0x614ab0b8 > > #idlepc = 0x614ab0cc > > #idlepc = 0x6026b438 > > #idlepc = 0x62b1c780 > > #idlepc = 0x60c05010 > > #*** Windows Configuration PATH *** > > #cnfg = C:\DYNAMIPS\Startup_Configs\R8.txt > > # > > #*** Linux Configuration PATH *** > > cnfg = /home/tyson/DYNAMIPS/Startup_Configs/R8.txt > > s0/0 = R7 s0/0 > > f0/0 = Cat2 f1/8 > > f0/1 = Cat4 f1/8 > > > > [[ROUTER R9]] > > model = 3725 > > console = 2009 > > autostart = False > > ghostios = true > > sparsemem = true > > #idlepc = 0x62b200d8 > > #idlepc = 0x62b200dc > > #idlepc = 0x60c0aa58 > > #idlepc = 0x614ab010 > > idlepc = 0x614ab070 > > #idlepc = 0x614ab0b8 > > #idlepc = 0x614ab0cc > > #idlepc = 0x6026b438 > > #idlepc = 0x62b1c780 > > #idlepc = 0x60c05010 > > #*** Windows Configuration PATH *** > > #cnfg = C:\DYNAMIPS\Startup_Configs\R9.txt > > # > > #*** Linux Configuration PATH *** > > cnfg = /home/tyson/DYNAMIPS/Startup_Configs/R9.txt > > f0/0 = Cat2 f1/9 > > f0/1 = Cat4 f1/9 > > slot2 = NM-4T > > s2/0 = R6 s2/0 > > s2/1 = R6 s2/1 > > > > ############################### > > # # > > # Third Hypervisor # > > # # > > ############################### > > [localhost:7203] > > # > > # Uncomment the appropriate Line for the Operating system you are > > running > > # *** Windows Working Directory *** > > #workingdir = C:\DYNAMIPS\Working > > # > > # *** Linux Working Directory *** > > workingdir = /home/tyson/DYNAMIPS/Working/ > > # > > udp = 10300 > > > > [[3725]] > > # > > # Uncomment the appropriate Line for the Operating system you > > are running > > #*** Windows IMAGE PATH *** > > #image = > > C:\DYNAMIPS\IMAGES\c3725-adventerprisek9-mz.124-15.T9.bin.unpacked > > # > > #*** Linux IMAGE PATH *** > > image = > > > /home/tyson/DYNAMIPS/IMAGES/c3725-adventerprisek9-mz.124-15.T9.bin.unpacked > > # > > ram = 256 > > > > [[ROUTER Cat1]] > > model = 3725 > > console = 2010 > > autostart = False > > ghostios = true > > sparsemem = true > > #idlepc = 0x62b200d8 > > #idlepc = 0x62b200dc > > idlepc = 0x60c0aa58 > > #idlepc = 0x614ab010 > > #idlepc = 0x614ab070 > > #idlepc = 0x614ab0b8 > > #idlepc = 0x614ab0cc > > #idlepc = 0x6026b438 > > #idlepc = 0x62b1c780 > > #idlepc = 0x60c05010 > > #*** Windows Configuration PATH *** > > #cnfg = C:\DYNAMIPS\Startup_Configs\Cat1.txt > > # > > #*** Linux Configuration PATH *** > > cnfg = /home/tyson/DYNAMIPS/Startup_Configs/Cat1.txt > > slot1 = NM-16ESW > > f1/0 = Cat2 f1/0 > > f1/1 = R1 f0/0 > > f1/2 = R2 f1/0 > > f1/4 = R4 f0/0 > > f1/5 = R5 f0/0 > > f1/9 = BB1 e0/0 > > f1/10 = Cat4 f1/10 > > f1/11 = Cat4 f1/11 > > f1/12 = Cat3 f1/12 > > f1/13 = Cat3 f1/13 > > f1/14 = Cat2 f1/14 > > f1/15 = Cat2 f1/15 > > > > [[ROUTER Cat2]] > > model = 3725 > > console = 2014 > > autostart = False > > ghostios = true > > sparsemem = true > > #idlepc = 0x62b200d8 > > #idlepc = 0x62b200dc > > #idlepc = 0x60c0aa58 > > #idlepc = 0x614ab010 > > #idlepc = 0x614ab070 > > #idlepc = 0x614ab0b8 > > #idlepc = 0x614ab0cc > > #idlepc = 0x6026b438 > > #idlepc = 0x62b1c780 > > idlepc = 0x60c05044 > > #*** Windows Configuration PATH *** > > #cnfg = C:\DYNAMIPS\Startup_Configs\Cat2.txt > > # > > #*** Linux Configuration PATH *** > > cnfg = /home/tyson/DYNAMIPS/Startup_Configs/Cat2.txt > > slot1 = NM-16ESW > > f1/0 = Cat1 f1/0 > > f1/1 = R1 f0/1 > > f1/2 = BB2 e0/0 > > f1/3 = BB3 e0/0 > > f1/6 = R6 f0/0 > > f1/7 = R7 f0/0 > > f1/8 = R8 f0/0 > > f1/9 = R9 f0/0 > > f1/10 = Cat3 f1/10 > > f1/11 = Cat3 f1/11 > > f1/12 = Cat4 f1/12 > > f1/13 = Cat4 f1/13 > > f1/14 = Cat1 f1/14 > > f1/15 = Cat1 f1/15 > > > > [[ROUTER Cat3]] > > model = 3725 > > console = 2015 > > autostart = False > > ghostios = true > > sparsemem = true > > #idlepc = 0x62b200d8 > > #idlepc = 0x62b200dc > > #idlepc = 0x60c0aa58 > > #idlepc = 0x614ab010 > > idlepc = 0x614ab070 > > #idlepc = 0x614ab0b8 > > #idlepc = 0x614ab0cc > > #idlepc = 0x6026b438 > > #idlepc = 0x62b1c780 > > #idlepc = 0x60c05010 > > #*** Windows Configuration PATH *** > > #cnfg = C:\DYNAMIPS\Startup_Configs\Cat3.txt > > # > > #*** Linux Configuration PATH *** > > cnfg = /home/tyson/DYNAMIPS/Startup_Configs/Cat3.txt > > slot1 = NM-16ESW > > f1/2 = R2 f1/1 > > f1/4 = R4 f0/1 > > f1/5 = R5 f0/1 > > f1/10 = Cat2 f1/10 > > f1/11 = Cat2 f1/11 > > f1/12 = Cat1 f1/12 > > f1/13 = Cat1 f1/13 > > f1/14 = Cat4 f1/14 > > f1/15 = Cat4 f1/15 > > > > [[ROUTER Cat4]] > > model = 3725 > > console = 2016 > > autostart = False > > ghostios = true > > sparsemem = true > > #idlepc = 0x62b200d8 > > #idlepc = 0x62b200dc > > #idlepc = 0x60c0aa58 > > idlepc = 0x614ab010 > > #idlepc = 0x614ab070 > > #idlepc = 0x614ab0b8 > > #idlepc = 0x614ab0cc > > #idlepc = 0x6026b438 > > #idlepc = 0x62b1c780 > > #idlepc = 0x60c05010 > > #*** Windows Configuration PATH *** > > #cnfg = C:\DYNAMIPS\Startup_Configs\Cat4.txt > > # > > #*** Linux Configuration PATH *** > > cnfg = /home/tyson/DYNAMIPS/Startup_Configs/Cat4.txt > > slot1 = NM-16ESW > > f1/6 = R6 f0/1 > > f1/7 = R7 f0/1 > > f1/8 = R8 f0/1 > > f1/9 = R9 f0/1 > > f1/10 = Cat1 f1/10 > > f1/11 = Cat1 f1/11 > > f1/12 = Cat2 f1/12 > > f1/13 = Cat2 f1/13 > > f1/14 = Cat3 f1/14 > > f1/15 = Cat3 f1/15 > > > > ############################### > > # # > > # Fourth Hypervisor # > > # # > > ############################### > > [localhost:7204] > > # > > # Uncomment the appropriate Line for the Operating system you are > > running > > # *** Windows Working Directory *** > > #workingdir = C:\DYNAMIPS\Working > > # > > # *** Linux Working Directory *** > > workingdir = /home/tyson/DYNAMIPS/Working/ > > # > > udp = 10400 > > > > [[2610]] > > # > > # Uncomment the appropriate Line for the Operating system you > > are running > > #*** Windows IMAGE PATH *** > > #image = C:\DYNAMIPS\IMAGES\c2600-j1s3-mz.123-26.bin.unpacked > > # > > #*** Linux IMAGE PATH *** > > image = > > /home/tyson/DYNAMIPS/IMAGES/c2600-j1s3-mz.123-26.bin.unpacked > > # > > chassis = 2610 > > > > [[ROUTER BB1]] > > model = 2610 > > console = 2011 > > autostart = False > > ghostios = true > > sparsemem = true > > #idlepc = 0x803d0234 > > #idlepc = 0x803d0bd4 > > idlepc = 0x803d0d18 > > #idlepc = 0x802f9a80 > > #idlepc = 0x802f9ab4 > > #idlepc = 0x802f9ac8 > > #idlepc = 0x8043aed0 > > #idlepc = 0x803cddb8 > > #idlepc = 0x803cef64 > > #cnfg = C:\DYNAMIPS\Startup_Configs\BB3.txt > > # > > #*** Linux Configuration PATH *** > > cnfg = /home/tyson/DYNAMIPS/Startup_Configs/BB3.txt > > e0/0 = Cat1 f1/9 > > > > [[ROUTER BB2]] > > model = 2610 > > console = 2012 > > autostart = False > > ghostios = true > > sparsemem = true > > #idlepc = 0x803d0234 > > #idlepc = 0x803d0bd4 > > #idlepc = 0x803d0d18 > > idlepc = 0x802f9a80 > > #idlepc = 0x802f9ab4 > > #idlepc = 0x802f9ac8 > > #idlepc = 0x8043aed0 > > #idlepc = 0x803cddb8 > > #idlepc = 0x803cef64 > > #cnfg = C:\DYNAMIPS\Startup_Configs\BB2.txt > > # > > #*** Linux Configuration PATH *** > > cnfg = /home/tyson/DYNAMIPS/Startup_Configs/BB2.txt > > e0/0 = Cat2 f1/2 > > > > [[ROUTER BB3]] > > model = 2610 > > console = 2013 > > autostart = False > > ghostios = true > > sparsemem = true > > #idlepc = 0x803d0234 > > #idlepc = 0x803d0bd4 > > #idlepc = 0x803d0d18 > > #idlepc = 0x802f9a80 > > idlepc = 0x802f9ab4 > > #idlepc = 0x802f9ac8 > > #idlepc = 0x8043aed0 > > #idlepc = 0x803cddb8 > > #idlepc = 0x803cef64 > > #*** Windows Configuration PATH *** > > #cnfg = C:\DYNAMIPS\Startup_Configs\BB1.txt > > # > > #*** Linux Configuration PATH *** > > cnfg = /home/tyson/DYNAMIPS/Startup_Configs/BB1.txt > > e0/0 = Cat2 f1/3 > > > > [[FRSW FR-Switch]] > > 2:204 = 4:402 > > 2:205 = 5:502 > > 2:206 = 6:602 > > 2:214 = 4:412 > > 2:215 = 5:512 > > 2:216 = 6:612 > > 2:224 = 4:422 > > 2:225 = 5:522 > > 2:226 = 6:622 > > 4:402 = 2:204 > > 4:405 = 5:504 > > 4:406 = 6:604 > > 4:412 = 2:214 > > 4:415 = 5:514 > > 4:416 = 6:614 > > 4:422 = 2:224 > > 4:425 = 5:524 > > 4:426 = 6:624 > > 5:502 = 2:205 > > 5:504 = 4:405 > > 5:506 = 6:605 > > 5:512 = 2:215 > > 5:514 = 4:415 > > 5:516 = 6:615 > > 5:522 = 2:225 > > 5:524 = 4:425 > > 5:526 = 6:625 > > 6:602 = 2:206 > > 6:604 = 4:406 > > 6:605 = 5:506 > > 6:612 = 2:216 > > 6:614 = 4:416 > > 6:615 = 5:516 > > 6:622 = 2:226 > > 6:624 = 4:426 > > 6:625 = 5:526 > > > > Regards, > > > > Tyson Scott - CCIE #13513 R&S and Security > > Technical Instructor - IPexpert, Inc. > > > > Telephone: +1.810.326.1444 > > Cell: +1.248.504.7309 > > Fax: +1.810.454.0130 > > Mailto: [email protected] > > > > Join our free online support and peer group communities: > > http://www.IPexpert.com/communities<http://www.ipexpert.com/communities> > > > > IPexpert - The Global Leader in Self-Study, Classroom-Based, Video On > Demand > > and Audio Certification Training Tools for the Cisco CCIE R&S Lab, CCIE > > Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and CCIE Storage > > Lab Certifications. > > > > > > > > ------------------------------ > Windows Live™: Keep your life in sync. Check it > out!<http://windowslive.com/explore?ocid=TXT_TAGLM_WL_t1_allup_explore_012009> > > > > ------------------------------ > What can you do with the new Windows Live? Find > out<http://www.microsoft.com/windows/windowslive/default.aspx> >
