It should be operational although we very rarely use it. If you need it and have an issue, just get with support and they will take care of you.
On Sun, Sep 6, 2009 at 8:58 PM, Rob <[email protected]> wrote: > Thanks Joe! You helped me out again. I just happened to notice from my > redrawing of the diagrams on each lab that some sometimes F0/0 is used and > other times it was F0/1. I never caught that the map I was looking for > was only in there when it did not met that diagram you told me about > > > > One thing that I am not sure if it is an issue with the lab, or that the > Proctor labs setup that I am using this weekend does not match is related to > Vol 2 Lab 9. The Gig port from R2 does not appear to be plugged in > anywhere. It was not a major detail. Once I noticed that even hard > coding speed and duplex had no affect and even shutting down the port had no > report on any switch I just assumed the cable is not there. I just > reconfigured slightly and just noted the difference in a lab task. Do you > know if The Gig port for R2 is normally operational on the Proctor lab > racks? > > > > Rob > > > ------------------------------ > > *From:* Joe Astorino [mailto:[email protected]] > *Sent:* Sunday, September 06, 2009 1:19 AM > *To:* Rob > *Cc:* GAURAV MADAN; CCIE OSL > > *Subject:* Re: [OSL | CCIE_RS] Vol 2 lab 7 task 1.5 > > > > Hey Rob! > > So the diagrams provided for the specific labs are logical in nature. To > get the physical topology, you need to look at the general physical topology > diagram. That is not provided in every single lab, because it never > changes. To download it if you do not have it, check out > http://proctorlabs.com/PDF/RS_9_std_top.pdf > > In my studying days, I printed that bad boy out and tacked it up on the > wall : ) > > HTH > > On Sat, Sep 5, 2009 at 10:09 AM, Rob <[email protected]> > wrote: > > I actually have all of that however there is no where I can see within the > drawing provided nor in the instruction that would say the BB1 is on Port > 11. I can easily tell which switch it is plugged into just not the port. > > No of the routers on the diagrams have that information either however the > do show up in CDP so I could tell. (actually I already need from all of > the > prior labs in WB1 and the others in WB2 that I have done but at this point > I > am playing dumb as if this is the first time I have ever seen this setup) > > I am wondering is that information was missed when writing the lab or if it > is that way for a reason and I just have not figured it out as of yet. > > Rob > > > -----Original Message----- > From: GAURAV MADAN [mailto:[email protected]] > Sent: Saturday, September 05, 2009 8:58 AM > To: Rob > Cc: CCIE OSL > Subject: Re: [OSL | CCIE_RS] Vol 2 lab 7 task 1.5 > > From one of the topology diagrams given ; you can always make out .. > whats the physical topology . > In fact from my opinion .... thats the way to start the exam .. draw > physical topo diagrams and mark the vlans on port .. This will make > life much easier. > > HTH > Gaurav Madan > > > On Sat, Sep 5, 2009 at 6:53 PM, Rob<[email protected]> wrote: > > How are you to know what port the BB routers are in when setting up the > > vlans? The Proctor guide only shows setting up the vlan number and never > > but does not show actually setting the vlans on the switches. I know > what > > switch the BB router is on, however the BB routers are not talking CDP > and > > unless I am just overlooking something I do not see where it tells you > the > > port on the switch. > > > > Rob > > > > _______________________________________________ > > For more information regarding industry leading CCIE Lab training, please > > visit www.ipexpert.com > > > > > > No virus found in this incoming message. > Checked by AVG - www.avg.com > Version: 8.5.409 / Virus Database: 270.13.71/2334 - Release Date: 09/04/09 > 17:51:00 > > > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > > > > -- > Regards, > > Joe Astorino - CCIE #24347 R&S > Technical Instructor - IPexpert, Inc. > Cell: +1.586.212.6107 > Fax: +1.810.454.0130 > Mailto: [email protected] > > No virus found in this incoming message. > Checked by AVG - www.avg.com > Version: 8.5.409 / Virus Database: 270.13.71/2334 - Release Date: 09/05/09 > 17:50:00 > -- Regards, Joe Astorino - CCIE #24347 R&S Technical Instructor - IPexpert, Inc. Cell: +1.586.212.6107 Fax: +1.810.454.0130 Mailto: [email protected]
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
