Yup, its working but kinda confusing :
on R2 :
R2(config)#do show fram map
Serial0/1/0 (up): ip 150.100.100.5 dlci 205(0xCD,0x30D0), static,
broadcast,
CISCO, status defined, inactive
Serial0/1/0 (up): ip 150.100.100.2 dlci 205(0xCD,0x30D0), static,
CISCO, status defined, inactive
Serial0/1/0 (up): ip 150.100.100.6 dlci 206(0xCE,0x30E0), static,
broadcast,
CISCO, status defined, inactive
Serial0/1/0.1 (up): point-to-point dlci, dlci 214(0xD6,0x3460), broadcast
status defined, active
Serial0/1/0 (up): ip 150.100.24.4 dlci *224 *(0xE0,0x3800), dynamic,
broadcast,, status defined, active
R2(config)#
*R2#sh run | s Serial0/1/0
interface Serial0/1/0
description Frame Relay Links
ip address 150.100.100.2 255.255.255.0
encapsulation frame-relay
frame-relay map ip 150.100.100.5 205 broadcast
frame-relay map ip 150.100.100.6 206 broadcast
frame-relay map ip 150.100.100.2 205
no frame-relay inverse-arp
interface Serial0/1/0.1 point-to-point
ip address 150.100.24.2 255.255.255.0
frame-relay interface-dlci 214
R2#*
**
*on R4 : *
*R4#show run | s Serial0/0/0
interface Serial0/0/0
ip address 150.100.24.4 255.255.255.0
encapsulation frame-relay
frame-relay interface-dlci 412
*
*R4#show fram map
Serial0/0/0 (up): ip 150.100.100.2 dlci 402(0x192,0x6420), dynamic,
broadcast,, status defined, active
Serial0/0/0 (up): ip 150.100.24.2 dlci 412(0x19C,0x64C0), dynamic,
broadcast,, status defined, active
R4#*
---
R4#ping 150.100.24.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 150.100.24.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
R4#
On Thu, Sep 2, 2010 at 1:10 AM, Jason Maynard <[email protected]>wrote:
> You have your answer, the dlci is assigned to the wrong interface
>
>
>
> Copy and paste this – I know others shut the interface then make changes
> but I find it quicker to copy then default then paster
>
>
>
> *default inter serial 0/1/0*
>
> *interface Serial0/1/0**
> description Frame Relay Links
> ip address 150.100.100.2 255.255.255.0
> encapsulation frame-relay
> frame-relay map ip 150.100.100.2 205
> frame-relay map ip 150.100.100.6 206 broadcast
> frame-relay map ip 150.100.100.5 205 broadcast
> no frame-relay inverse-arp
> interface Serial0/1/0.1 point-to-point
> ip address 150.100.24.2 255.255.255.0*
>
> * no frame-relay inverse-arp*
>
> * frame-relay interface-dlci 214***
>
>
>
>
>
> *From:* Amer Mustafa [mailto:[email protected]]
> *Sent:* September-01-10 6:06 PM
>
> *To:* Jason Maynard
> *Cc:* [email protected]
> *Subject:* Re: [OSL | CCIE_RS] Workbook 1 , LAB6 (Frame-Relay).
>
>
>
> i have tried this even before i send to you :
>
>
>
> R2(config-subif)#do show fram map
> Serial0/1/0 (up): ip 150.100.100.2 dlci 205(0xCD,0x30D0), static,
> CISCO, status defined, inactive
> Serial0/1/0 (up): ip 150.100.100.5 dlci 205(0xCD,0x30D0), static,
> broadcast,
> CISCO, status defined, inactive
> Serial0/1/0 (up): ip 150.100.100.6 dlci 206(0xCE,0x30E0), static,
> broadcast,
> CISCO, status defined, inactive
> Serial0/1/0 (up): ip 150.100.24.4 dlci 214(0xD6,0x3460), dynamic,
> broadcast,, status defined, active
> R2(config-subif)#fram
> R2(config-subif)#frame-relay inter
> R2(config-subif)#frame-relay interface-dlci 214 ?
> cisco Use CISCO Encapsulation
> ietf Use RFC1490/RFC2427 Encapsulation
> ppp Use RFC1973 Encapsulation to support PPP over FR
> protocol Optional protocol information for remote end
> <cr>
>
> R2(config-subif)#frame-relay interface-dlci 214
> *%PVC already assigned to interface Serial0/1/0*
> R2(config-subif)#
>
> On Thu, Sep 2, 2010 at 12:59 AM, Jason Maynard <[email protected]>
> wrote:
>
> *R2(config)#do sh run | s Serial0/1/0**
> interface Serial0/1/0
> description Frame Relay Links
> ip address 150.100.100.2 255.255.255.0
> encapsulation frame-relay
> frame-relay map ip 150.100.100.2 205
> frame-relay map ip 150.100.100.6 206 broadcast
> frame-relay map ip 150.100.100.5 205 broadcast
> no frame-relay inverse-arp
> interface Serial0/1/0.1 point-to-point
> ip address 150.100.24.2 255.255.255.0*
>
> * frame-relay interface-dlci #*
>
>
>
> *From:* Amer Mustafa [mailto:[email protected]]
> *Sent:* September-01-10 5:52 PM
> *To:* Jason Maynard
> *Cc:* [email protected]
> *Subject:* Re: [OSL | CCIE_RS] Workbook 1 , LAB6 (Frame-Relay).
>
>
>
> *Nope, its not working.*
>
>
>
> *R4(config-if)#do show fram map**
> Serial0/0/0 (up): ip 150.100.100.2 dlci 412 (0x19C,0x64C0), dynamic,
> broadcast,, status defined, active
> R4(config-if)#do sh run | s Serial0/0/0
> interface Serial0/0/0
> ip address 150.100.24.4 255.255.255.0
> encapsulation frame-relay
> frame-relay interface-dlci 412
> R4(config-if)#do ping 150.100.24.2*
>
> *Type escape sequence to abort.**
> Sending 5, 100-byte ICMP Echos to 150.100.24.2, timeout is 2 seconds:
> .....
> Success rate is 0 percent (0/5)
> R4(config-if)#*
>
> On Thu, Sep 2, 2010 at 12:44 AM, Jason Maynard <[email protected]>
> wrote:
>
>
>
>
>
> Do sh “show frame map” to see that you are missing IP to DLCI mappings
>
>
>
> Add “frame-relay interface-dlci #” command
>
>
>
> *From:* [email protected] [mailto:
> [email protected]] *On Behalf Of *Amer Mustafa
> *Sent:* September-01-10 5:41 PM
> *To:* [email protected]
> *Subject:* [OSL | CCIE_RS] Workbook 1 , LAB6 (Frame-Relay).
>
>
>
> I am on task 6.4 for LAB 6 WB1.
>
>
>
> on R4 :
>
>
>
> *R4#show run | s Serial0/0/0**
> interface Serial0/0/0
> ip address 150.100.24.4 255.255.255.0
> encapsulation frame-relay
> R4#ping 150.100.24.4*
>
> *Type escape sequence to abort.**
> Sending 5, 100-byte ICMP Echos to 150.100.24.4, timeout is 2 seconds:
> .....
> Success rate is 0 percent (0/5)*
>
>
>
> on R2 :
>
>
>
> *R2(config)#do sh run | s Serial0/1/0**
> interface Serial0/1/0
> description Frame Relay Links
> ip address 150.100.100.2 255.255.255.0
> encapsulation frame-relay
> frame-relay map ip 150.100.100.2 205
> frame-relay map ip 150.100.100.6 206 broadcast
> frame-relay map ip 150.100.100.5 205 broadcast
> no frame-relay inverse-arp
> interface Serial0/1/0.1 point-to-point
> ip address 150.100.24.2 255.255.255.0
> R2(config)#do ping 150.100.24.2*
>
> *Type escape sequence to abort.**
> Sending 5, 100-byte ICMP Echos to 150.100.24.2, timeout is 2 seconds:
> .....
> Success rate is 0 percent (0/5)
> R2(config)#*
>
>
>
> *what could be the reason ?*
>
>
>
> *======================*
>
>
>
> *regards ... *
>
> *Amer*
>
>
>
>
>
>
>
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
