Good. but why we have assigned " frame interface-dlci 214" from where we get this "214" since we are not running any inve arp and our show fram mapp commands doesnt show 214.
On Thu, Sep 2, 2010 at 1:38 AM, Jason Maynard <[email protected]>wrote: > Your problem was that you learned all the DLCI by inverse arp which > assigned them to the physical interface. > > > > Most likely you configured the interface while it was up and before you > could turn off inverse arp and therefore learned all the DLCI’s that were > available. > > > > If you would have shut the physical interface then configured encapsulation > and no frame-relay inverse-arp plus all other configuration and then brought > up the interface you would not have a problem. > > > > > > *From:* Amer Mustafa [mailto:[email protected]] > *Sent:* September-01-10 6:33 PM > > *To:* Jason Maynard > *Cc:* [email protected] > *Subject:* Re: [OSL | CCIE_RS] Workbook 1 , LAB6 (Frame-Relay). > > > > jason, > > > > Thanks alot, its working, but can you explain one point to me !? > > > > how and why we have decided to 214 on R2 !? > > > > if you remove the config to the default, and then configure one by one, you > will endup having the same error, and when do show fram map you will not > find any mappings for Serial0/1/0.1. > > > > the only mapping avilable is 150.100.24.4 ! > > > > Please advise. > > On Thu, Sep 2, 2010 at 1:23 AM, Amer Mustafa <[email protected]> > wrote: > > Yup, its working but kinda confusing : > > > > > > on R2 : > > > > R2(config)#do show fram map > > > Serial0/1/0 (up): ip 150.100.100.5 dlci 205(0xCD,0x30D0), static, > broadcast, > CISCO, status defined, inactive > Serial0/1/0 (up): ip 150.100.100.2 dlci 205(0xCD,0x30D0), static, > CISCO, status defined, inactive > Serial0/1/0 (up): ip 150.100.100.6 dlci 206(0xCE,0x30E0), static, > broadcast, > CISCO, status defined, inactive > > Serial0/1/0.1 (up): point-to-point dlci, dlci 214(0xD6,0x3460), broadcast > status defined, active > Serial0/1/0 (up): ip 150.100.24.4 dlci *224** *(0xE0,0x3800), dynamic, > broadcast,, status defined, active > R2(config)# > > > > *R2#sh run | s Serial0/1/0 * > > * > interface Serial0/1/0 > description Frame Relay Links > ip address 150.100.100.2 255.255.255.0 > encapsulation frame-relay* > > * frame-relay map ip 150.100.100.5 205 broadcast * > > * > frame-relay map ip 150.100.100.6 206 broadcast* > > * frame-relay map ip 150.100.100.2 205 * > > * > no frame-relay inverse-arp > interface Serial0/1/0.1 point-to-point > ip address 150.100.24.2 255.255.255.0* > > * frame-relay interface-dlci 214 ** > R2#* > > > > *on R4 : * > > *R4#show run | s Serial0/0/0 > interface Serial0/0/0 > ip address 150.100.24.4 255.255.255.0 > encapsulation frame-relay* > > * frame-relay interface-dlci 412* > > *R4#show fram map** > Serial0/0/0 (up): ip 150.100.100.2 dlci 402(0x192,0x6420), dynamic, > broadcast,, status defined, active > Serial0/0/0 (up): ip 150.100.24.2 dlci 412(0x19C,0x64C0), dynamic, > broadcast,, status defined, active > R4#* > > > > --- > > > > R4#ping 150.100.24.2 > > Type escape sequence to abort. > Sending 5, 100-byte ICMP Echos to 150.100.24.2, timeout is 2 seconds: > !!!!! > > Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms > R4# > > On Thu, Sep 2, 2010 at 1:10 AM, Jason Maynard <[email protected]> > wrote: > > You have your answer, the dlci is assigned to the wrong interface > > > > Copy and paste this – I know others shut the interface then make changes > but I find it quicker to copy then default then paster > > > > *default inter serial 0/1/0* > > *interface Serial0/1/0** > description Frame Relay Links > ip address 150.100.100.2 255.255.255.0 > encapsulation frame-relay > frame-relay map ip 150.100.100.2 205 > frame-relay map ip 150.100.100.6 206 broadcast > frame-relay map ip 150.100.100.5 205 broadcast > no frame-relay inverse-arp > interface Serial0/1/0.1 point-to-point > ip address 150.100.24.2 255.255.255.0* > > * no frame-relay inverse-arp* > > * frame-relay interface-dlci 214* > > > > > > *From:* Amer Mustafa [mailto:[email protected]] > *Sent:* September-01-10 6:06 PM > > > *To:* Jason Maynard > *Cc:* [email protected] > *Subject:* Re: [OSL | CCIE_RS] Workbook 1 , LAB6 (Frame-Relay). > > > > i have tried this even before i send to you : > > > > R2(config-subif)#do show fram map > Serial0/1/0 (up): ip 150.100.100.2 dlci 205(0xCD,0x30D0), static, > CISCO, status defined, inactive > Serial0/1/0 (up): ip 150.100.100.5 dlci 205(0xCD,0x30D0), static, > broadcast, > CISCO, status defined, inactive > Serial0/1/0 (up): ip 150.100.100.6 dlci 206(0xCE,0x30E0), static, > broadcast, > CISCO, status defined, inactive > Serial0/1/0 (up): ip 150.100.24.4 dlci 214(0xD6,0x3460), dynamic, > broadcast,, status defined, active > R2(config-subif)#fram > R2(config-subif)#frame-relay inter > R2(config-subif)#frame-relay interface-dlci 214 ? > cisco Use CISCO Encapsulation > ietf Use RFC1490/RFC2427 Encapsulation > ppp Use RFC1973 Encapsulation to support PPP over FR > protocol Optional protocol information for remote end > <cr> > > R2(config-subif)#frame-relay interface-dlci 214 > *%PVC already assigned to interface Serial0/1/0* > R2(config-subif)# > > On Thu, Sep 2, 2010 at 12:59 AM, Jason Maynard <[email protected]> > wrote: > > *R2(config)#do sh run | s Serial0/1/0** > interface Serial0/1/0 > description Frame Relay Links > ip address 150.100.100.2 255.255.255.0 > encapsulation frame-relay > frame-relay map ip 150.100.100.2 205 > frame-relay map ip 150.100.100.6 206 broadcast > frame-relay map ip 150.100.100.5 205 broadcast > no frame-relay inverse-arp > interface Serial0/1/0.1 point-to-point > ip address 150.100.24.2 255.255.255.0* > > * frame-relay interface-dlci #* > > > > *From:* Amer Mustafa [mailto:[email protected]] > *Sent:* September-01-10 5:52 PM > *To:* Jason Maynard > *Cc:* [email protected] > *Subject:* Re: [OSL | CCIE_RS] Workbook 1 , LAB6 (Frame-Relay). > > > > *Nope, its not working.* > > > > *R4(config-if)#do show fram map** > Serial0/0/0 (up): ip 150.100.100.2 dlci 412 (0x19C,0x64C0), dynamic, > broadcast,, status defined, active > R4(config-if)#do sh run | s Serial0/0/0 > interface Serial0/0/0 > ip address 150.100.24.4 255.255.255.0 > encapsulation frame-relay > frame-relay interface-dlci 412 > R4(config-if)#do ping 150.100.24.2* > > *Type escape sequence to abort.** > Sending 5, 100-byte ICMP Echos to 150.100.24.2, timeout is 2 seconds: > ..... > Success rate is 0 percent (0/5) > R4(config-if)#* > > On Thu, Sep 2, 2010 at 12:44 AM, Jason Maynard <[email protected]> > wrote: > > > > > > Do sh “show frame map” to see that you are missing IP to DLCI mappings > > > > Add “frame-relay interface-dlci #” command > > > > *From:* [email protected] [mailto: > [email protected]] *On Behalf Of *Amer Mustafa > *Sent:* September-01-10 5:41 PM > *To:* [email protected] > *Subject:* [OSL | CCIE_RS] Workbook 1 , LAB6 (Frame-Relay). > > > > I am on task 6.4 for LAB 6 WB1. > > > > on R4 : > > > > *R4#show run | s Serial0/0/0** > interface Serial0/0/0 > ip address 150.100.24.4 255.255.255.0 > encapsulation frame-relay > R4#ping 150.100.24.4* > > *Type escape sequence to abort.** > Sending 5, 100-byte ICMP Echos to 150.100.24.4, timeout is 2 seconds: > ..... > Success rate is 0 percent (0/5)* > > > > on R2 : > > > > *R2(config)#do sh run | s Serial0/1/0** > interface Serial0/1/0 > description Frame Relay Links > ip address 150.100.100.2 255.255.255.0 > encapsulation frame-relay > frame-relay map ip 150.100.100.2 205 > frame-relay map ip 150.100.100.6 206 broadcast > frame-relay map ip 150.100.100.5 205 broadcast > no frame-relay inverse-arp > interface Serial0/1/0.1 point-to-point > ip address 150.100.24.2 255.255.255.0 > R2(config)#do ping 150.100.24.2* > > *Type escape sequence to abort.** > Sending 5, 100-byte ICMP Echos to 150.100.24.2, timeout is 2 seconds: > ..... > Success rate is 0 percent (0/5) > R2(config)#* > > > > *what could be the reason ?* > > > > *======================* > > > > *regards ... * > > *Amer* > > > > > > > > > > >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
