Can you ping 150.100.24.4 from R2?
From: Nilesh Mehta [mailto:[email protected]]
Sent: Wednesday, October 06, 2010 4:13 PM
To: Di Bias, Steve
Cc: [email protected]
Subject: Re: [OSL | CCIE_RS] WB1 - LAB8 -Task 1-2
All the loopback addresses in routing table except only R4. I can ping to all
loopback from R1to R9 but not routes for 200.0.0.4
On Wed, Oct 6, 2010 at 2:46 PM, Di Bias, Steve
<[email protected]<mailto:[email protected]>> wrote:
Well you are advertising 200.0.0.0 in RIP so what do you see on R2 when you
issue the following command
"show ip route 200.0.0.4"
Steve
From:
[email protected]<mailto:[email protected]>
[mailto:[email protected]<mailto:[email protected]>]
On Behalf Of Nilesh Mehta
Sent: Wednesday, October 06, 2010 1:59 PM
To: [email protected]<mailto:[email protected]>
Subject: [OSL | CCIE_RS] WB1 - LAB8 -Task 1-2
I was trying to setup neighbor adjacency between R2 and R4. I have same
configuration as per DSG
but I was not able to connect R4 loop back's address. R4's loop back address
never appeared in routing table
(200.0.0.4).I have both up/up status for serial link on both side and I tried
with no validate source command on R4 and split horizon on R2 but it did not
work. Not sure what could be problem? Any one has this problem earlier ? Please
let me know
Thanks--Nilesh
----------------------------------------------------------
R4(config-router)#do sh run | s rip
router rip
version 2
passive-interface default
no passive-interface Serial0/0/0
network 150.100.0.0
network 200.0.0.0
no auto-summary
-----------------------------------
R2#sh run | s rip
description Ethernet Link to R1
description Frame Relay Links
description Frame Relay Cloud 2
description Frame Relay Cloud 1
description Serial Link to R5
router rip
version 2
passive-interface default
no passive-interface GigabitEthernet0/0
no passive-interface Serial0/1/0.24
no passive-interface Serial0/1/0.256
no passive-interface Serial0/2/0
network 150.100.0.0
network 200.0.0.0
no auto-summary
------------------------------------------------------------------------------------------------------------
--------------------------------------------------
R4#
*Oct 6 05:55:05.535: RIP: ignored v2 update from bad source 150.100.100.5 on
Serial0/0/0
R4#
*Oct 6 05:55:09.179: RIP: ignored v2 update from bad source 150.100.100.6 on
Serial0/0/0
R4#
*Oct 6 05:55:10.587: RIP: sending v2 update to 224.0.0.9 via Serial0/0/0
(150.100.24.4)
*Oct 6 05:55:10.587: RIP: build update entries
*Oct 6 05:55:10.587: 150.100.24.0/24<http://150.100.24.0/24> via 0.0.0.0,
metric 1, tag 0
*Oct 6 05:55:10.587: 150.100.40.0/24<http://150.100.40.0/24> via 0.0.0.0,
metric 1, tag 0
*Oct 6 05:55:10.587: 150.100.41.0/24<http://150.100.41.0/24> via 0.0.0.0,
metric 1, tag 0
*Oct 6 05:55:10.587: 200.0.0.4/32<http://200.0.0.4/32> via 0.0.0.0, metric
1, tag 0
R4#
*Oct 6 05:55:35.139: RIP: ignored v2 update from bad source 150.100.100.5 on
Serial0/0/0
R4#
*Oct 6 05:55:36.967: RIP: sending v2 update to 224.0.0.9 via Serial0/0/0
(150.100.24.4)
*Oct 6 05:55:36.967: RIP: build update entries
*Oct 6 05:55:36.967: 150.100.24.0/24<http://150.100.24.0/24> via 0.0.0.0,
metric 1, tag 0
*Oct 6 05:55:36.967: 150.100.40.0/24<http://150.100.40.0/24> via 0.0.0.0,
metric 1, tag 0
*Oct 6 05:55:36.967: 150.100.41.0/24<http://150.100.41.0/24> via 0.0.0.0,
metric 1, tag 0
*Oct 6 05:55:36.967: 200.0.0.4/32<http://200.0.0.4/32> via 0.0.0.0, metric
1, tag 0
*Oct 6 05:55:37.483: RIP: ignored v2 update from bad source 150.100.100.6 on
Serial0/0/0
R4#
---------------------------------------------------------------------------------------------------------------------
R2#
R2#*Oct 6 05:42:08.283: RIP: sending v2 update to 224.0.0.9 via Serial0/1/0.24
(150.100.24.2)
*Oct 6 05:42:08.283: RIP: build update entries
*Oct 6 05:42:08.283: 66.0.0.0/8<http://66.0.0.0/8> via 0.0.0.0, metric 12,
tag 0
*Oct 6 05:42:08.283: 66.110.173.0/24<http://66.110.173.0/24> via 0.0.0.0,
metric 10, tag 0
*Oct 6 05:42:08.283: 66.203.191.0/24<http://66.203.191.0/24> via 0.0.0.0,
metric 10, tag 0
*Oct 6 05:42:08.283: 100.0.0.0/8<http://100.0.0.0/8> via 0.0.0.0, metric 4,
tag 0
*Oct 6 05:42:08.283: 100.100.100.0/24<http://100.100.100.0/24> via 0.0.0.0,
metric 2, tag 0
*Oct 6 05:42:08.283: 150.100.12.0/24<http://150.100.12.0/24> via 0.0.0.0,
metric 1, tag 0
*Oct 6 05:42:08.283: 150.100.24.0/24<http://150.100.24.0/24> via 0.0.0.0,
metric 1, tag 0
*Oct 6 05:42:08.283: 150.100.25.0/24<http://150.100.25.0/24> via 0.0.0.0,
metric 1, tag 0
*Oct 6 05:42:08.283: 150.100.69.0/24<http://150.100.69.0/24> via 0.0.0.0,
metric 2, tag 0
*Oct 6 05:42:08.283: 150.100.78.0/24<http://150.100.78.0/24> via 0.0.0.0,
metric 3, tag 0
*Oct 6 05:42:08.283: 150.100.81.0/24<http://150.100.81.0/24> via 0.0.0.0,
metric 4, tag 0
*Oct 6 05:42:08.283: 150.100.91.0/24<http://150.100.91.0/24> via 0.0.0.0,
metric 3, tag 0
*Oct 6 05:42:08.283: 150.100.100.0/24<http://150.100.100.0/24> via 0.0.0.0,
metric 1, tag 0
*Oct 6 05:42:08.283: 150.100.220.0/24<http://150.100.220.0/24> via 0.0.0.0,
metric 2, tag 0
------------------------------------------------------------------------------
UHS Confidentiality Notice: This e-mail message, including any attachments, is
for the sole use of the intended recipient(s) and may contain confidential and
privileged information. Any unauthorized review, use, disclosure or
distribution of this information is prohibited, and may be punishable by law.
If this was sent to you in error, please notify the sender by reply e-mail and
destroy all copies of the original message.
UHS Confidentiality Notice: This e-mail message, including any attachments, is
for the sole use of the intended recipient (s) and may contain confidential and
privileged information. Any unauthorized review, use, disclosure or
distribution of this information is prohibited. If this was sent to you in
error, please notify the sender by reply e-mail and destroy all copies of the
original message.
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
