Wait, you did say DHCP snooping was on, so is the interface connecting to the DHCP server (R6) a trusted port?
Thank you, Steve E. Di Bias Network Engineer - Information Systems Valley Health System - Las Vegas Office - 702- 369-7594 Cell - 702-241-1801 [email protected] -----Original Message----- From: Di Bias, Steve Sent: Saturday, August 06, 2011 10:39 PM To: 'Cedric King'; [email protected] Subject: RE: [OSL | CCIE_RS] L1v3task 2-4 Cedric, I just labbed this up and everything is working great. Are the two interfaces on R6 and R7 in the same VLAN? Also I noticed that your bba-group has an incorrect configuration: You have bba-group pppoe group global interface virtual-temp 1 But the "interface" is incorrect and should actually be bba-group pppoe group global virtual-temp 1 Here are my configs with show commands: R6 (config) interface Virtual-Template1 ip address 141.41.67.6 255.255.255.0 ip mtu 1492 ip dhcp excluded-address 141.41.67.6 ip dhcp pool PPPoE network 141.41.67.0 /24 interface FastEthernet0/0 no ip address duplex auto speed auto pppoe enable group CCIE bba-group pppoe CCIE virtual-template 1 Now we'll configure the dialer pool, interface, and tie it back to F0/0 R7 (config) interface Dialer1 encap ppp ip mtu 1492 ip address dhcp dialer pool 1 interface FastEthernet0/0 no ip address duplex auto speed auto pppoe enable pppoe-client dial-pool-number 1 R7(config-if)#do sh ip int br dialer1 Interface IP-Address OK? Method Status Protocol Dialer1 141.41.67.1 YES DHCP up up R7(config-if)#do p 141.41.67.6 Sending 5, 100-byte ICMP Echos to 141.41.67.6, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms Now over on the otherside let's verify the PPPoE session and DHCP binding table R6(config-if)#do sh pppoe sess all Total PPPoE sessions 1 session id: 17 local MAC address: e804.6224.d2a8, remote MAC address: 0017.5a06.a314 virtual access interface: Vi2.1, outgoing interface: Fa0/0 66 packets sent, 65 received 2072 bytes sent, 2502 received Looks good, what about the DHCP binding table R6(config-if)#do sh ip dhcp bind Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type Hardware address/ User name 141.41.67.1 0063.6973.636f.2d30. Jul 27 2011 10:41 PM Automatic 3031.372e.3561.3036. 2e61.3331.342d.4469. Thank you, Steve E. Di Bias Network Engineer - Information Systems Valley Health System - Las Vegas Office - 702- 369-7594 Cell - 702-241-1801 [email protected] -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Cedric King Sent: Saturday, August 06, 2011 8:19 PM To: [email protected] Subject: [OSL | CCIE_RS] L1v3task 2-4 I've been working on Task 2-4 Lab 1 workbook 3 for about two hours now and can not get the pppoe to come up between R6 - 7.. I have the following config a applied: r6 ------ bba-group pppoe group global interface virtual-temp 1 int virtual-temp 1 encap ppp ip addr x.x.67.6 255.255.255.0 ip mtu 1492 ip dhcp exclude-addr x.x.67.1 x.x.67.6 ip dhcp exclude-addr x.x.67.8 x.x.67.255 ip dhcp pool R67 network x.x.67.0 /24 int fa0/0 no ip addr pppoe enable group global R7 ---- int fa0/0 no ip addr pppoe-client dial-pool-number 1 int dialer 1 encap ppp ip mtu 1492 ip addr dhcp dialer pool 1 I've been through the solution guide and i've watched the video work book and have followed each step.. and its not working.. I've verified the physical set up of my devices and they are correct... Then I applied this setup to different devices in the lab and they worked.. they only thing different is dhcp snooping in enable in clan 67... If this is the cause. and I'm not saying it is... was this missed on purpose ? _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com UHS Confidentiality Notice: This e-mail message, including any attachments, is for the sole use of the intended recipient (s) and may contain confidential and privileged information. Any unauthorized review, use, disclosure or distribution of this information is prohibited. If this was sent to you in error, please notify the sender by reply e-mail and destroy all copies of the original message. _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
