Your network types don't match. On Feb 22, 2012 5:20 AM, "khaled al-ajeman" <[email protected]> wrote:
> Would you please guys help me with this problem althought I have done my > configuration correctly. By the way there is neighborhood relationship > between R2 AND R6, > but there is no relationship between R2 AND R5. > > > > R 2 > > Transmit Delay is 1 sec, State DR, Priority 1 > Designated Router (ID) 224.0.0.0, Interface address 150.100.100.2 > No backup designated router on this network > Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5 > oob-resync timeout 120 > Hello due in 00:00:20 > Supports Link-local Signaling (LLS) > Cisco NSF helper support enabled > IETF NSF helper support enabled > Index 1/4, flood queue length 0 > Next 0x0(0)/0x0(0) > Last flood scan length is 1, maximum is 31 > Last flood scan time is 0 msec, maximum is 12 msec > Neighbor Count is 1, Adjacent neighbor count is 1 > Adjacent with neighbor 200.0.0.6 > Suppress hello for 0 neighbor(s) > Message digest authentication enabled > Youngest key id is 2 > ---------------------------------------> KEY ID is different than R5, WHY? > > R5 > > R5(config-router)#do sh ip os int s0/0.56 > Serial0/0.56 is up, line protocol is up > Internet Address 150.100.100.5/24, Area 0 > Process ID 1, Router ID 200.0.0.5, Network Type NON_BROADCAST, Cost: 1562 > Transmit Delay is 1 sec, State DROTHER, Priority 0 > No designated router on this network > No backup designated router on this network > Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5 > oob-resync timeout 120 > Hello due in 00:00:18 > Supports Link-local Signaling (LLS) > Cisco NSF helper support enabled > IETF NSF helper support enabled > Index 2/3, flood queue length 0 > Next 0x0(0)/0x0(0) > Last flood scan length is 0, maximum is 28 > Last flood scan time is 0 msec, maximum is 8 msec > Neighbor Count is 0, Adjacent neighbor count is 0 > Suppress hello for 0 neighbor(s) > Message digest authentication enabled > Youngest key id is 1 > ---------------------- KEY ID IS DIFFERENT ? > > R2 > > interface Serial0/0.256 multipoint > bandwidth 64 > ip address 150.100.100.2 255.255.255.0 > ip ospf message-digest-key 1 md5 IPexpert ------> I have to have two > keys one going to R5 AND one going heading to R6 with different keys and > passwords > ip ospf message-digest-key 2 md5 CCIE > delay 2000 > snmp trap link-status > frame-relay map ip 150.100.100.5 205 broadcast > frame-relay map ip 150.100.100.6 206 broadcast > frame-relay map ip 150.100.100.2 206 > > > R2(config-subif)#do sh ip os nei > > Neighbor ID Pri State Dead Time Address Interface > N/A 0 ATTEMPT/DROTHER - 150.100.100.5 > Serial0/0.256 > 200.0.0.6 0 FULL/DROTHER 00:01:46 150.100.100.6 > Serial0/0.256 > 200.0.0.4 0 FULL/ - 00:00:37 150.100.24.4 > Serial0/0.24 > 200.0.0.5 0 FULL/ - 00:00:33 150.100.25.5 Serial0/2 > 200.0.0.1 1 FULL/DR 00:00:37 150.100.12.1 > FastEthernet0/1 > R2(config-subif)# > > R5 > > interface Serial0/0.56 multipoint > bandwidth 64 > ip address 150.100.100.5 255.255.255.0 > ip ospf message-digest-key 1 md5 IPexpert > ip ospf priority 0 > delay 2000 > snmp trap link-status > frame-relay map ip 150.100.100.5 502 > frame-relay map ip 150.100.100.6 502 > frame-relay map ip 150.100.100.2 502 broadcast > end > THANKS, > > KHALED > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com > > http://onlinestudylist.com/mailman/listinfo/ccie_rs > _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
