Hi guys, thanks it is working fine, what I did I just reconfigure my routers again.
thanks to you all On Wed, Feb 22, 2012 at 6:10 PM, Bob McCouch <[email protected]> wrote: > Ahh, I did look at that as well, but I think he just didn't paste full > output from the first router. > > > On Wed, Feb 22, 2012 at 10:07 AM, Rogelio Gamino <[email protected]>wrote: > >> Hard to see on a phone. I saw this.. Network Type NON_BROADCAST but >> didn't see it on the other output. >> >> >> On Wed, Feb 22, 2012 at 10:04 AM, Bob McCouch <[email protected]> wrote: >> >>> Sure they do. He didn't paste the very top of the 'sh ip ospf int' >>> command for the first router, but the timers are both: >>> >>> Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5 >>> >>> And they're both frame-relay multipoint subinterfaces, with no 'ip ospf >>> network' command configured. What leads you to believe the network types >>> don't match? >>> >>> He also clearly has the neighbor statement on R2, since you can see in >>> the R2 neighbor output that R2 is in "Attempt" and knows the IP of the R5 >>> neighbor, but not the RID. >>> >>> >>> On Wed, Feb 22, 2012 at 9:23 AM, Rogelio Gamino <[email protected]>wrote: >>> >>>> Your network types don't match. >>>> On Feb 22, 2012 5:20 AM, "khaled al-ajeman" <[email protected]> >>>> wrote: >>>> >>>> > Would you please guys help me with this problem althought I have done >>>> my >>>> > configuration correctly. By the way there is neighborhood >>>> relationship >>>> > between R2 AND R6, >>>> > but there is no relationship between R2 AND R5. >>>> > >>>> > >>>> > >>>> > R 2 >>>> > >>>> > Transmit Delay is 1 sec, State DR, Priority 1 >>>> > Designated Router (ID) 224.0.0.0, Interface address 150.100.100.2 >>>> > No backup designated router on this network >>>> > Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit >>>> 5 >>>> > oob-resync timeout 120 >>>> > Hello due in 00:00:20 >>>> > Supports Link-local Signaling (LLS) >>>> > Cisco NSF helper support enabled >>>> > IETF NSF helper support enabled >>>> > Index 1/4, flood queue length 0 >>>> > Next 0x0(0)/0x0(0) >>>> > Last flood scan length is 1, maximum is 31 >>>> > Last flood scan time is 0 msec, maximum is 12 msec >>>> > Neighbor Count is 1, Adjacent neighbor count is 1 >>>> > Adjacent with neighbor 200.0.0.6 >>>> > Suppress hello for 0 neighbor(s) >>>> > Message digest authentication enabled >>>> > Youngest key id is 2 >>>> > ---------------------------------------> KEY ID is different than R5, >>>> WHY? >>>> > >>>> > R5 >>>> > >>>> > R5(config-router)#do sh ip os int s0/0.56 >>>> > Serial0/0.56 is up, line protocol is up >>>> > Internet Address 150.100.100.5/24, Area 0 >>>> > Process ID 1, Router ID 200.0.0.5, Network Type NON_BROADCAST, Cost: >>>> 1562 >>>> > Transmit Delay is 1 sec, State DROTHER, Priority 0 >>>> > No designated router on this network >>>> > No backup designated router on this network >>>> > Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit >>>> 5 >>>> > oob-resync timeout 120 >>>> > Hello due in 00:00:18 >>>> > Supports Link-local Signaling (LLS) >>>> > Cisco NSF helper support enabled >>>> > IETF NSF helper support enabled >>>> > Index 2/3, flood queue length 0 >>>> > Next 0x0(0)/0x0(0) >>>> > Last flood scan length is 0, maximum is 28 >>>> > Last flood scan time is 0 msec, maximum is 8 msec >>>> > Neighbor Count is 0, Adjacent neighbor count is 0 >>>> > Suppress hello for 0 neighbor(s) >>>> > Message digest authentication enabled >>>> > Youngest key id is 1 >>>> > ---------------------- KEY ID IS DIFFERENT ? >>>> > >>>> > R2 >>>> > >>>> > interface Serial0/0.256 multipoint >>>> > bandwidth 64 >>>> > ip address 150.100.100.2 255.255.255.0 >>>> > ip ospf message-digest-key 1 md5 IPexpert ------> I have to have >>>> two >>>> > keys one going to R5 AND one going heading to R6 with different keys >>>> and >>>> > passwords >>>> > ip ospf message-digest-key 2 md5 CCIE >>>> > delay 2000 >>>> > snmp trap link-status >>>> > frame-relay map ip 150.100.100.5 205 broadcast >>>> > frame-relay map ip 150.100.100.6 206 broadcast >>>> > frame-relay map ip 150.100.100.2 206 >>>> > >>>> > >>>> > R2(config-subif)#do sh ip os nei >>>> > >>>> > Neighbor ID Pri State Dead Time Address >>>> Interface >>>> > N/A 0 ATTEMPT/DROTHER - 150.100.100.5 >>>> > Serial0/0.256 >>>> > 200.0.0.6 0 FULL/DROTHER 00:01:46 150.100.100.6 >>>> > Serial0/0.256 >>>> > 200.0.0.4 0 FULL/ - 00:00:37 150.100.24.4 >>>> > Serial0/0.24 >>>> > 200.0.0.5 0 FULL/ - 00:00:33 150.100.25.5 >>>> Serial0/2 >>>> > 200.0.0.1 1 FULL/DR 00:00:37 150.100.12.1 >>>> > FastEthernet0/1 >>>> > R2(config-subif)# >>>> > >>>> > R5 >>>> > >>>> > interface Serial0/0.56 multipoint >>>> > bandwidth 64 >>>> > ip address 150.100.100.5 255.255.255.0 >>>> > ip ospf message-digest-key 1 md5 IPexpert >>>> > ip ospf priority 0 >>>> > delay 2000 >>>> > snmp trap link-status >>>> > frame-relay map ip 150.100.100.5 502 >>>> > frame-relay map ip 150.100.100.6 502 >>>> > frame-relay map ip 150.100.100.2 502 broadcast >>>> > end >>>> > THANKS, >>>> > >>>> > KHALED >>>> > _______________________________________________ >>>> > For more information regarding industry leading CCIE Lab training, >>>> please >>>> > visit www.ipexpert.com >>>> > >>>> > Are you a CCNP or CCIE and looking for a job? Check out >>>> > www.PlatinumPlacement.com <http://www.platinumplacement.com/> >>>> > >>>> > http://onlinestudylist.com/mailman/listinfo/ccie_rs >>>> > >>>> _______________________________________________ >>>> For more information regarding industry leading CCIE Lab training, >>>> please visit www.ipexpert.com >>>> >>>> Are you a CCNP or CCIE and looking for a job? Check out >>>> www.PlatinumPlacement.com <http://www.platinumplacement.com/> >>>> >>>> http://onlinestudylist.com/mailman/listinfo/ccie_rs >>>> >>> >>> >> > _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
