do you have a vrf lite instance of rip running anywhere, the bgp side needs to know of it
where does trace fail, then post those relevant configs -- BR Tony Sent from my iPad On 2 Feb 2013, at 00:33, "Bodnar, Edward" <[email protected]> wrote: > So I have 6 total routers. > > RIP 6(CE)---1(PE)---2(P)---3(P)---4(PE)---5(CE) BGP > > I can ping from rip side to BGP routes. But cannot ping from BGP to rip side. > > > > -----Original Message----- > From: Tony Singh [mailto:[email protected]] > Sent: Friday, February 01, 2013 7:23 PM > To: Tony Singh > Cc: Bodnar, Edward; [email protected] > Subject: Re: [OSL | CCIE_RS] BGP PE - CE configuration > > Take that back, was thinking a use case at work where we have vrf definitions > to separate routing tables on the CE as we face PE > > Debug ip icmp > > ping vrf B 55.55.55.55 > > From r4 > > What happens > > As bob said check mpls ldp nei, also check not acl copp distribute or filter > list is in the way.. > > -- > BR > > Tony > > Sent from my iPad > > On 2 Feb 2013, at 00:01, Tony Singh <[email protected]> wrote: > >> Can't see vrf definition on R5 presumably your CE? >> >> -- >> BR >> >> Tony >> >> Sent from my iPad >> >> On 1 Feb 2013, at 22:24, "Bodnar, Edward" <[email protected]> wrote: >> >>> I can never seem to get this to work. I can See routes end to end but I am >>> missing something when I use BGP as the PE - CE protocol. I thought BGP >>> was supposed to be the easy one J >>> >>> >>> >>> >>> >>> I have full connectivity. And I can see routes Just can't ping. >>> >>> >>> >>> RT4: >>> >>> router bgp 1 >>> >>> no bgp default ipv4-unicast >>> >>> bgp log-neighbor-changes >>> >>> neighbor 1.1.1.1 remote-as 1 >>> >>> neighbor 1.1.1.1 update-source Loopback0 >>> >>> neighbor 10.10.45.5 remote-as 5 >>> >>> ! >>> >>> address-family ipv4 >>> >>> neighbor 1.1.1.1 activate >>> >>> neighbor 10.10.45.5 activate >>> >>> no auto-summary >>> >>> no synchronization >>> >>> exit-address-family >>> >>> ! >>> >>> address-family vpnv4 >>> >>> neighbor 1.1.1.1 activate >>> >>> neighbor 1.1.1.1 send-community both >>> >>> exit-address-family >>> >>> ! >>> >>> address-family ipv4 vrf B >>> >>> neighbor 10.10.45.5 remote-as 5 >>> >>> neighbor 10.10.45.5 activate >>> >>> no synchronization >>> >>> exit-address-family >>> >>> >>> >>> >>> >>> >>> >>> >>> >>> >>> >>> R5(config-router)#do sh run | s bgp >>> >>> router bgp 5 >>> >>> no synchronization >>> >>> bgp log-neighbor-changes >>> >>> network 55.55.55.55 mask 255.255.255.255 >>> >>> neighbor 10.10.45.4 remote-as 1 >>> >>> no auto-summary >>> >>> >>> >>> >>> >>> _______________________________________________ >>> For more information regarding industry leading CCIE Lab training, please >>> visit www.ipexpert.com >>> >>> Are you a CCNP or CCIE and looking for a job? Check out >>> www.PlatinumPlacement.com >>> >>> http://onlinestudylist.com/mailman/listinfo/ccie_rs _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
