as in ipexpert lab workbooks, you need 1x26x1xm router (Access Server) 3x26x1xm routers (BACK BONE)
4xCAT3560-24TS-S 7x2811 Routers 1x3825/3845 Router 1x2611/2800 series with almost 1 NM Slot/3620/3640/3660 as Frame relay switch (R3) 1x2801 Router as R9 if you like to play with udld you need 2xSFP-SX-MM with a multimode lc-lc patch to connect between CAT1 to R2 (gig0/1-Gig0/1) that's my contribution! best regards.! Edgar Still #unnumbered! On Mon, Oct 7, 2013 at 5:13 PM, Hesham Abdelkereem <[email protected] > wrote: > The training vendors usually are very close to the real lab as well. > I used INE for Voice stuff and all the equipment and modules are same as > the real lab the only difference was the routers itself. > I am not intending to breach NDA or asking for the exam content itself such > as questions , answers , usernames , ip addresses or passwords but the > thing is the Blueprint is not clear at all about the modules. > In the Voice track blueprint it was more clear about the T1/E1 modules > needs to be used in the test but in R/S scenario they just give a very > little information. > > > > On 7 October 2013 12:37, Bob McCouch <[email protected]> wrote: > > > Pick the topology for the training vendor you're using and build to that. > > > > The exact topology and models in use in the real lab are not published in > > their entirety. If someone gives you an exact list for the real lab, > > they're lying or violating NDA. > > > > > > On Mon, Oct 7, 2013 at 3:16 PM, Hesham Abdelkereem < > > [email protected]> wrote: > > > >> Dear Experts, > >> > >> > >> I just would like to know the CCE R/S V4 Lab Equipment > >> > >> I know for fact if I am not mistaken it should be > >> > >> 6X CISCO 1841 Routers > >> 3X CISCO 3825 Routers for Backbone > >> 4X Catalyst 3560 Switches 3560-24TS-S > >> > >> I already read this link > >> > >> > http://www.ine.com/downloads/routing_switching_rack_rental_hardware_specification_v1.2.pdf > >> > >> But I would like to make the lab as close to the real V4 lab as much as > >> possible for better and speedy strategy. > >> > >> I would like to know in detail how many WIC-1T should be installed and > how > >> about the Backbone do they use WIC-1T or NM-4A/S > >> > >> I am just newbie but it would be good to start build the lab as it will > >> ease the studies. > >> > >> Many Thanks, > >> Hesham > >> _______________________________________________ > >> For more information regarding industry leading CCIE Lab training, > please > >> visit www.ipexpert.com > >> > >> Are you a CCNP or CCIE and looking for a job? Check out > >> www.PlatinumPlacement.com > >> > >> http://onlinestudylist.com/mailman/listinfo/ccie_rs > >> > > > > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com > > http://onlinestudylist.com/mailman/listinfo/ccie_rs > _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
