Any opinion should be respected even if its against IPX:) its free of speech and we don't make any bad talks about anyone. We are not in jail here:) we can speak any say our opinion freeily.
Thanks brother have you ever made any attempts? I wish you all success. I am CCNA and NP routing and switching but I dont have extensive hands-on experience on routing , IPV6 , BGP , MPLS , OSPF and that stuff. Thanks, Hesham On 7 October 2013 18:55, <[email protected]> wrote: > Hi again. > > We'll in my humble opinion, I preffer kick ass IPExpert workbooks for over > IN* ones. > > Why? simple... > > Technology focus over and over again in the IPExpert wb, on the other > vendor the deployment of the workbook is just confuse ... > > Again is my humble opinion > > Best regards > > Edgar > > Sent from my iPhone > > On 07-10-2013, at 21:41, Hesham Abdelkereem <[email protected]> > wrote: > > Hi Edgar, > > Thanks for your great contribution. I just would like to clarify why do we > have 9 routers + 3 2621 Backbone > INE is just 6 Router + 3 Backbones that gives total of 9 routers all. > > Hahaha It got me confused now , Now I don't know which is better topology > IPX or INE? > I know that owners here may get mad at me because I mentioned INE but in > all cases I am not promoting them or market their product so I should be > fine:). > > > > > On 7 October 2013 17:35, Edgar Mauricio Diaz Orellana < > [email protected]> wrote: > >> as in ipexpert lab workbooks, you need >> >> 1x26x1xm router (Access Server) >> 3x26x1xm routers (BACK BONE) >> >> 4xCAT3560-24TS-S >> >> 7x2811 Routers >> 1x3825/3845 Router >> 1x2611/2800 series with almost 1 NM Slot/3620/3640/3660 as Frame relay >> switch (R3) >> 1x2801 Router as R9 >> >> >> if you like to play with udld you need 2xSFP-SX-MM with a multimode lc-lc >> patch to connect between CAT1 to R2 (gig0/1-Gig0/1) >> >> that's my contribution! >> >> best regards.! >> >> Edgar >> Still #unnumbered! >> >> >> On Mon, Oct 7, 2013 at 5:13 PM, Hesham Abdelkereem < >> [email protected]> wrote: >> >>> The training vendors usually are very close to the real lab as well. >>> I used INE for Voice stuff and all the equipment and modules are same as >>> the real lab the only difference was the routers itself. >>> I am not intending to breach NDA or asking for the exam content itself >>> such >>> as questions , answers , usernames , ip addresses or passwords but the >>> thing is the Blueprint is not clear at all about the modules. >>> In the Voice track blueprint it was more clear about the T1/E1 modules >>> needs to be used in the test but in R/S scenario they just give a very >>> little information. >>> >>> >>> >>> On 7 October 2013 12:37, Bob McCouch <[email protected]> wrote: >>> >>> > Pick the topology for the training vendor you're using and build to >>> that. >>> > >>> > The exact topology and models in use in the real lab are not published >>> in >>> > their entirety. If someone gives you an exact list for the real lab, >>> > they're lying or violating NDA. >>> > >>> > >>> > On Mon, Oct 7, 2013 at 3:16 PM, Hesham Abdelkereem < >>> > [email protected]> wrote: >>> > >>> >> Dear Experts, >>> >> >>> >> >>> >> I just would like to know the CCE R/S V4 Lab Equipment >>> >> >>> >> I know for fact if I am not mistaken it should be >>> >> >>> >> 6X CISCO 1841 Routers >>> >> 3X CISCO 3825 Routers for Backbone >>> >> 4X Catalyst 3560 Switches 3560-24TS-S >>> >> >>> >> I already read this link >>> >> >>> >> >>> http://www.ine.com/downloads/routing_switching_rack_rental_hardware_specification_v1.2.pdf >>> >> >>> >> But I would like to make the lab as close to the real V4 lab as much >>> as >>> >> possible for better and speedy strategy. >>> >> >>> >> I would like to know in detail how many WIC-1T should be installed >>> and how >>> >> about the Backbone do they use WIC-1T or NM-4A/S >>> >> >>> >> I am just newbie but it would be good to start build the lab as it >>> will >>> >> ease the studies. >>> >> >>> >> Many Thanks, >>> >> Hesham >>> >> _______________________________________________ >>> >> For more information regarding industry leading CCIE Lab training, >>> please >>> >> visit www.ipexpert.com >>> >> >>> >> Are you a CCNP or CCIE and looking for a job? Check out >>> >> www.PlatinumPlacement.com >>> >> >>> >> http://onlinestudylist.com/mailman/listinfo/ccie_rs >>> >> >>> > >>> > >>> _______________________________________________ >>> For more information regarding industry leading CCIE Lab training, >>> please visit www.ipexpert.com >>> >>> Are you a CCNP or CCIE and looking for a job? Check out >>> www.PlatinumPlacement.com >>> >>> http://onlinestudylist.com/mailman/listinfo/ccie_rs >>> >> >> >> >> > _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
