Okay, but I gave you the exact specs. Limit it to 750k. End of requirement.
Police, police rate, or doesn't matter? Sent from my iPhone On Oct 16, 2013, at 11:19 AM, Ryan Krcelic <[email protected]> wrote: > The biggest thing to know is that the police rate command is used with CoPP. > If you are just policing you have to choose between 1 bucket or 2 bucket. > Police xxx is 1 bucket and police cir xxx is 2 bucket. > > If you are doing a police statement that is going into a service policy that > will be applied to an interface, use either police or police rate depending > on the throughput and the be/bc values. > V/r, > > Ryan Krcelic > > > > On Wed, Oct 16, 2013 at 11:53 AM, Joe S <[email protected]> wrote: >> Gaah....class-map match-any FTP >> >> Nobody needs to correct me on that part! >> >> >> On Wed, Oct 16, 2013 at 10:50 AM, Joe S <[email protected]> wrote: >> >> > I appreciate the feedback, and if I'd asked my question more clearly maybe >> > it would have been a bit better. >> > >> > The only stipulation in the lab was "Limit FTP traffic to 750Kbps". >> > >> > So in my answer I just did: >> > class-map FTP >> > match protocol secure-ftp >> > match protocol ftp >> > policy-map LIMIT >> > class FTP >> > police 750000 >> > >> > Meanwhile, the book solution was the exact same thing except their police >> > statement was: >> > police rate 750000 >> > >> > It's a difficult set of stuff to search for, too, because a word like >> > "rate" tends to show up on all the same pages as "police" anyway... >> > >> > >> > On Wed, Oct 16, 2013 at 10:45 AM, Tony Singh <[email protected]>wrote: >> > >> >> >> >> Joe >> >> >> >> Here's some of my notes, read the RFC's below for a deeper understanding. >> >> >> >> Single Rate Two Color Policer (One Bucket) >> >> >> >> police 96 bc x be x >> >> confirm action >> >> exced action >> >> >> >> >> >> Single Rate Three Color Policer (Two Buckets) [srTCM RFC 2697] >> >> >> >> police cir x bc x be x >> >> confirm action >> >> exceed action >> >> violate action >> >> >> >> >> >> Two Rate Three Color Policer (Two Buckets) [trTCM RFC 2698] >> >> >> >> Here you define CIR and PIR >> >> >> >> police rate (cir) x (pir) x >> >> confirm action >> >> exceed action >> >> violate action >> >> >> >> The buckets by definition are either conform=one and conform and >> >> violate=two >> >> >> >> -- >> >> BR >> >> >> >> Tony >> >> >> >> Sent from my iPhone on 3 >> >> >> >> > On 16 Oct 2013, at 15:38, Joe S <[email protected]> wrote: >> >> > >> >> > As I continue through I find another difference between my solution and >> >> the >> >> > DSG's solution. And I'm having trouble finding an answer online. >> >> > >> >> > In a policy map, what is the difference between a "police" command and a >> >> > "police rate" command? >> >> > _______________________________________________ >> >> > For more information regarding industry leading CCIE Lab training, >> >> please visit www.ipexpert.com >> >> > >> >> > Are you a CCNP or CCIE and looking for a job? Check out >> >> www.PlatinumPlacement.com >> >> > >> >> > http://onlinestudylist.com/mailman/listinfo/ccie_rs >> >> >> > >> > >> _______________________________________________ >> For more information regarding industry leading CCIE Lab training, please >> visit www.ipexpert.com >> >> Are you a CCNP or CCIE and looking for a job? Check out >> www.PlatinumPlacement.com >> >> http://onlinestudylist.com/mailman/listinfo/ccie_rs > _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
