I know on one customer's 7200VXRs and the ASR1Ks we replaced them with, "match VLAN" was supported and we used it heavily for applying policy to VLAN sub-interfaces from a carrier Ether handoff. Anyone try it using a 7200 image in Dynamips?
Bob -- Sent from my iPhone, please excuse any typos. > On Jan 3, 2014, at 9:52 AM, Edgar Mauricio Diaz Orellana > <[email protected]> wrote: > > on my WS-C3750G-24-TS-S > > Enter configuration commands, one per line. End with CNTL/Z. > core01(config)#class-map match-all VLANB > core01(config-cmap)#match ? > access-group Access group > input-interface Select one or more input interfaces to match > ip IP specific values > protocol Protocol > > core01(config-cmap)#match > > > on my ME-3750-24 > > ME-3750(config)#class-map match-all VLANB > ME-3750(config-cmap)#match ? > access-group Access group > cos IEEE 802.1Q/ISL class of service/user priority values > input-interface Select an input interface to match > ip IP specific values > mpls Multi Protocol Label Switching specific values > protocol Protocol > vlan VLANs to match > > > so it appears on Metro platform you could match vlans and mpls and cos !! > > best regards. > > >> On Fri, Jan 3, 2014 at 7:49 AM, <[email protected]> wrote: >> >> Also in my switches I have same problem: >> >> Rack4SW1(config-cmap)#match ? >> access-group Access group >> any Any packets >> input-interface Select one or more input interfaces to match >> ip IP specific values >> not Negate this match result >> packet Layer 3 Packet length >> protocol Protocol >> >> However if LAN interested are interaface transit Layer3 you can use >> follow option: >> >> match input-interface (VLAN LAYER3) >> >>> On Fri, Jan 3, 2014, at 11:26 AM, [email protected] wrote: >>> I have a question relating to Task 9.1 WB2 Lab2. Traffic shaping. The DSG >>> answer for this has a command that I cannot find out how to to: >>> >>> >>> class-map match-all VLANB >>> → match vlan 12 (THIS CANNOT BE DONE on the switch but can be done on a >>> router.) >>> >>> I have tried several IOS’s on my own switches and then tested this on the >>> proctor labs kit with the same result. It does not exist as a command. >>> Anyone come across this issue and what did you do to resolve it. Please >>> help. >>> >>> >>> Jason >>> _______________________________________________ >>> Free CCIE R&S, Collaboration, Data Center, Wireless & Security Videos :: >>> >>> iPexpert on YouTube: www.youtube.com/ipexpertinc >> >> >> -- >> This message is intended for the individual(s) to whom it is addressed >> and may contain information that is privileged or confidential. >> If you are not the addressee you must not read,use or disclose the >> contents of this email. >> Whilst all reasonable care has been taken to avoid the transmission of >> viruses, the recipient should carry out virus and other checks, >> as they consider appropriate. >> Myself accepts no responsibility in this regard. >> _______________________________________________ >> Free CCIE R&S, Collaboration, Data Center, Wireless & Security Videos :: >> >> iPexpert on YouTube: www.youtube.com/ipexpertinc > > > > -- > > Edgar Díaz Orellana > CCENT/CCNA/CCDA/CCNA Security, CCNP, CCNP Security en progreso. > Kaspersky Administrator / Technical Specialist > Microsoft Certified Professional. > Celular : 09-91283087 / 09-94118996 > skype: eorellan1969 > _______________________________________________ > Free CCIE R&S, Collaboration, Data Center, Wireless & Security Videos :: > > iPexpert on YouTube: www.youtube.com/ipexpertinc _______________________________________________ Free CCIE R&S, Collaboration, Data Center, Wireless & Security Videos :: iPexpert on YouTube: www.youtube.com/ipexpertinc
