3.3 2008/7/10 Steven Quek <[EMAIL PROTECTED]>:
> Hi, > > May I know for the CCIE Voice Lab which SRND version is used? > > Cheers > > ------------------------------ > > From: [EMAIL PROTECTED] > To: [EMAIL PROTECTED] > Date: Thu, 10 Jul 2008 08:20:11 -0400 > CC: ccie_voice@onlinestudylist.com > > Subject: Re: [OSL | CCIE_Voice] 0 Conf max sessions > > Thank you Mike. > > On Jul 9, 2008, at 11:29 PM, Mike Stevenson wrote: > > As was mentioned.. > a PVDM2-16 contains 1 DSP, when a DSP is configured as a Conference Bridge, > the rtr loads the required firmware into the DSP. A DSP that has been > configured as a Conference Bridge, cannot also be used as a transcoder or > terminate PSTN calls. > > from the config profile 1 is conf-b, profile 2 is xcoder. both cannot run > on the same DSP, for this config to work you would either require a PVDM2-32 > (this contains 2 DSPs) or greater, or or the existing PVDM2-16, and another > PVDM2-(8 or 16 or more) > > PVDM2-8 = .5 DSP > PVDM2-16 = 1 DSP > PVDM2-32 = 2 DSP > etc.. > > > This is all covered in the CCM SRND. > > > Cheers > > On 10/07/2008, at 12:56 PM, Michael Thompson wrote: > > Onur, just curious where this ended up. > > On Mon, Jul 7, 2008 at 4:36 PM, Jonathan Charles <[EMAIL PROTECTED]> > wrote: > > Post a show diag, I think your DSPs may be hosed... prob bad > firmware.... but this is a WAG > > > Jonathan > > On Mon, Jul 7, 2008 at 9:41 AM, Onur Tufekci <[EMAIL PROTECTED]> > wrote: > > And this is if I do it other way around: > > > > router2(config-dspfarm-profile)#dspfarm profile 2 > > router2(config-dspfarm-profile)#shut > > Disabling profile will disconnect active TRANSCODING calls, > > do you want to continue ? [yes/no]y > > router2(config-dspfarm-profile)# > > router2(config-dspfarm-profile)# > > router2(config-dspfarm-profile)#dspfarm profile 1 > > router2(config-dspfarm-profile)#no shut > > router2(config-dspfarm-profile)#dspfarm profile 2 > > router2(config-dspfarm-profile)#no shut > > Enabling profile failed due to insufficient TRANSCODING resources, > > resources available to support 0 sessions; please modify the > > configuration and retry > > router2(config-dspfarm-profile)# > > > > On Mon, Jul 7, 2008 at 10:39 AM, Onur Tufekci <[EMAIL PROTECTED]> > > wrote: > >> > >> Here is the configuration and results: > >> > >> router2(config)#do show run > >> Building configuration... > >> Current configuration : 2938 bytes > >> ! > >> ! Last configuration change at 15:11:09 UTC Mon Jul 7 2008 > >> ! NVRAM config last updated at 14:49:04 UTC Mon Jul 7 2008 > >> ! > >> version 12.4 > >> service timestamps debug datetime msec > >> service timestamps log datetime msec > >> service password-encryption > >> ! > >> hostname router2 > >> ! > >> boot-start-marker > >> boot-end-marker > >> ! > >> card type t1 0 0 > >> no logging console > >> enable secret 5 $1$7cJ4$U9gWuPCv.H1DPdXYIyWJD0 > >> ! > >> no aaa new-model > >> ! > >> resource policy > >> ! > >> network-clock-participate wic 0 > >> ! > >> ! > >> ip cef > >> ! > >> ! > >> no ip domain lookup > >> ! > >> isdn switch-type primary-ni > >> ! > >> voice-card 0 > >> dspfarm > >> dsp services dspfarm > >> ! > >> ! > >> ! > >> ! > >> ! > >> ! > >> ! > >> ! > >> ! > >> ! > >> ! > >> ! > >> ! > >> ! > >> ! > >> ! > >> ! > >> ! > >> ! > >> controller T1 0/0/0 > >> framing esf > >> linecode b8zs > >> ! > >> controller T1 0/0/1 > >> framing esf > >> linecode b8zs > >> ! > >> ! > >> ! > >> ! > >> interface FastEthernet0/0 > >> ip address 192.168.2.1 255.255.255.0 > >> duplex full > >> speed 100 > >> h323-gateway voip bind srcaddr 192.168.2.1 > >> ! > >> interface FastEthernet0/1 > >> description Management_IP > >> ip address 192.168.10.2 255.255.255.0 > >> duplex full > >> speed 100 > >> ! > >> interface Service-Engine1/0 > >> no ip address > >> shutdown > >> ! > >> ip route 192.168.1.0 255.255.255.0 192.168.10.1 > >> ip route 192.168.3.0 255.255.255.0 192.168.10.3 > >> ! > >> ip http server > >> no ip http secure-server > >> ! > >> ! > >> ! > >> ! > >> control-plane > >> ! > >> ! > >> ! > >> ! > >> ! > >> sccp local FastEthernet0/0 > >> sccp ccm 192.168.2.1 identifier 1 > >> sccp > >> ! > >> sccp ccm group 1 > >> associate ccm 1 priority 1 > >> associate profile 2 register xcoder > >> associate profile 1 register conference > >> ! > >> dspfarm profile 2 transcode > >> codec g711ulaw > >> codec g729r8 > >> maximum sessions 4 > >> associate application SCCP > >> shutdown > >> ! > >> dspfarm profile 1 conference > >> codec g711ulaw > >> codec g729r8 > >> maximum sessions 1 > >> associate application SCCP > >> shutdown > >> ! > >> ! > >> dial-peer voice 1000 voip > >> answer-address 1... > >> destination-pattern 1... > >> session target ipv4:192.168.1.1 > >> codec g711ulaw > >> ! > >> dial-peer voice 9 pots > >> destination-pattern 9T > >> incoming called-number 14345552... > >> direct-inward-dial > >> ! > >> ! > >> ! > >> telephony-service > >> max-ephones 2 > >> max-dn 2 > >> ip source-address 192.168.2.1 port 2000 > >> auto assign 1 to 2 > >> system message Your current options > >> sdspfarm units 5 > >> sdspfarm tag 1 xcoder > >> sdspfarm tag 2 conference > >> dialplan-pattern 1 14345552... extension-length 4 > >> max-conferences 8 gain -6 > >> call-forward pattern .T > >> web admin system name cisco password cisco > >> dn-webedit > >> time-webedit > >> transfer-system full-consult > >> transfer-pattern .T > >> secondary-dialtone 9 > >> ! > >> ! > >> ephone-dn 1 dual-line > >> number 2001 > >> description 14345552001 > >> name Gil Grissom > >> ! > >> ! > >> > >> router2(config)#dspfarm > >> router2(config)# > >> router2(config)# > >> router2(config)# > >> router2(config)#dspfarm pro 2 > >> router2(config-dspfarm-profile)#no shut > >> router2(config-dspfarm-profile)#dspfarm pro 1 > >> router2(config-dspfarm-profile)#no shut > >> Enabling profile failed due to insufficient CONFERENCING resources, > >> resources available to support 0 sessions; please modify the > >> configuration and retry > >> router2(config-dspfarm-profile)#do show inv > >> NAME: "2811 chassis", DESCR: "2811 chassis" > >> PID: CISCO2811 , VID: V03 , SN: FHK103671CU > >> NAME: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 > >> SubSlot 0", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - > T1/E1" > >> PID: VWIC2-2MFT-T1/E1 , VID: V01 , SN: FOC102540TY > >> NAME: "PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 4", DESCR: "PVDMII > >> DSP SIMM with one DSP" > >> PID: PVDM2-16 , VID: V01 , SN: FOC1032054R > >> NAME: "NM-SE on Slot 1", DESCR: "NM-SE" > >> PID: NM-CUE , VID: V03, SN: FOC10120B2E > >> NAME: "40GB IDE Disc Daughter Card on Slot 1 SubSlot 0", DESCR: "40GB > IDE > >> Disc Daughter Card" > >> PID: , VID: 1.0, SN: FOC10170V2B > >> > >> > >> On Mon, Jul 7, 2008 at 9:14 AM, Onur Tufekci <[EMAIL PROTECTED]> > >> wrote: > >>> > >>> I actually configured all that right after I send this message but no > >>> luck. > >>> > >>> On Sun, Jul 6, 2008 at 11:23 PM, Vik Malhi <[EMAIL PROTECTED]> > wrote: > >>>> > >>>> try configuring sccp ccm and sccp ccm group before you set the max > >>>> sessions. > >>>> > >>>> > >>>> Vik Malhi �C CCIE #13890 > >>>> Senior Technical Instructor - IPexpert, Inc. > >>>> > >>>> Telephone: +1.810.326.1444 > >>>> Fax: +1.810.454.0130 > >>>> Mailto: [EMAIL PROTECTED] > >>>> > >>>> Join our free online support and peer group communities: > >>>> http://www.IPexpert.com/communities<http://www.ipexpert.com/communities> > >>>> > >>>> IPexpert - The Global Leader in Self-Study, Classroom-Based, > >>>> Video-On-Demand and Audio Certification Training Tools for the Cisco > CCIE > >>>> R&S Lab, CCIE Security Lab, CCIE Service Provider Lab , CCIE Voice Lab > and > >>>> CCIE Storage Lab Certifications. > >>>> > >>>> > >>>> ________________________________ > >>>> From: [EMAIL PROTECTED] > >>>> [mailto:[EMAIL PROTECTED] On Behalf Of Mehmet > Tufekci > >>>> Sent: Sunday, July 06, 2008 9:17 AM > >>>> To: ccievoice1 > >>>> Cc: OSL CCIE Voice Lab Exam > >>>> Subject: Re: [OSL | CCIE_Voice] 0 Conf max sessions > >>>> > >>>> > >>>> I have 1-3 configured under controller. > >>>> I am able to see 1-8 available resources under my transcoder profile > but > >>>> no luck with conference. I know conference will not show up if you > enable > >>>> transcoder profile first. No matter what I tried I can not get it to > run. > >>>> > >>>> > >>>> On Jul 6, 2008, at 11:44 AM, ccievoice1 wrote: > >>>> > >>>> have you utilized all the dsp resources for your pri-group? > >>>> > >>>> On Sun, Jul 6, 2008 at 11:31 PM, Mehmet Tufekci < > [EMAIL PROTECTED]> > >>>> wrote: > >>>>> > >>>>> Hi All, > >>>>> > >>>>> I can not figure out why maximum session <0-0> is showing under > >>>>> conference profile. > >>>>> > >>>>> I did not enable transcoding profile yet. > >>>>> > >>>>> voice-card 0 > >>>>> dspfarm > >>>>> dsp services dspfarm > >>>>> ! > >>>>> ! > >>>>> ! > >>>>> interface Loopback0 > >>>>> ip address 172.3.102.1 255.255.255.255 > >>>>> ip ospf network point-to-point > >>>>> ! > >>>>> ! > >>>>> sccp local Loopback0 > >>>>> sccp > >>>>> ! > >>>>> dspfarm profile 1 transcode > >>>>> codec g711ulaw > >>>>> codec g729r8 > >>>>> shutdown > >>>>> ! > >>>>> dspfarm profile 2 conference > >>>>> codec g711ulaw > >>>>> codec g729r8 > >>>>> shutdown > >>>>> ! > >>>>> > >>>>> > >>>> > >>>> > >>> > >> > > > > > > > > > > ------------------------------ > Make the most of what you can do on your PC and the Web, just the way you > want. Windows Live <http://www.get.live.com/wl/all> >