Onur, just curious where this ended up.
On Mon, Jul 7, 2008 at 4:36 PM, Jonathan Charles
<[EMAIL PROTECTED]> wrote:
Post a show diag, I think your DSPs may be hosed... prob bad
firmware.... but this is a WAG
Jonathan
On Mon, Jul 7, 2008 at 9:41 AM, Onur Tufekci
<[EMAIL PROTECTED]> wrote:
> And this is if I do it other way around:
>
> router2(config-dspfarm-profile)#dspfarm profile 2
> router2(config-dspfarm-profile)#shut
> Disabling profile will disconnect active TRANSCODING calls,
> do you want to continue ? [yes/no]y
> router2(config-dspfarm-profile)#
> router2(config-dspfarm-profile)#
> router2(config-dspfarm-profile)#dspfarm profile 1
> router2(config-dspfarm-profile)#no shut
> router2(config-dspfarm-profile)#dspfarm profile 2
> router2(config-dspfarm-profile)#no shut
> Enabling profile failed due to insufficient TRANSCODING
resources,
> resources available to support 0 sessions; please modify the
> configuration and retry
> router2(config-dspfarm-profile)#
>
> On Mon, Jul 7, 2008 at 10:39 AM, Onur Tufekci <[EMAIL PROTECTED]
>
> wrote:
>>
>> Here is the configuration and results:
>>
>> router2(config)#do show run
>> Building configuration...
>> Current configuration : 2938 bytes
>> !
>> ! Last configuration change at 15:11:09 UTC Mon Jul 7 2008
>> ! NVRAM config last updated at 14:49:04 UTC Mon Jul 7 2008
>> !
>> version 12.4
>> service timestamps debug datetime msec
>> service timestamps log datetime msec
>> service password-encryption
>> !
>> hostname router2
>> !
>> boot-start-marker
>> boot-end-marker
>> !
>> card type t1 0 0
>> no logging console
>> enable secret 5 $1$7cJ4$U9gWuPCv.H1DPdXYIyWJD0
>> !
>> no aaa new-model
>> !
>> resource policy
>> !
>> network-clock-participate wic 0
>> !
>> !
>> ip cef
>> !
>> !
>> no ip domain lookup
>> !
>> isdn switch-type primary-ni
>> !
>> voice-card 0
>> dspfarm
>> dsp services dspfarm
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> controller T1 0/0/0
>> framing esf
>> linecode b8zs
>> !
>> controller T1 0/0/1
>> framing esf
>> linecode b8zs
>> !
>> !
>> !
>> !
>> interface FastEthernet0/0
>> ip address 192.168.2.1 255.255.255.0
>> duplex full
>> speed 100
>> h323-gateway voip bind srcaddr 192.168.2.1
>> !
>> interface FastEthernet0/1
>> description Management_IP
>> ip address 192.168.10.2 255.255.255.0
>> duplex full
>> speed 100
>> !
>> interface Service-Engine1/0
>> no ip address
>> shutdown
>> !
>> ip route 192.168.1.0 255.255.255.0 192.168.10.1
>> ip route 192.168.3.0 255.255.255.0 192.168.10.3
>> !
>> ip http server
>> no ip http secure-server
>> !
>> !
>> !
>> !
>> control-plane
>> !
>> !
>> !
>> !
>> !
>> sccp local FastEthernet0/0
>> sccp ccm 192.168.2.1 identifier 1
>> sccp
>> !
>> sccp ccm group 1
>> associate ccm 1 priority 1
>> associate profile 2 register xcoder
>> associate profile 1 register conference
>> !
>> dspfarm profile 2 transcode
>> codec g711ulaw
>> codec g729r8
>> maximum sessions 4
>> associate application SCCP
>> shutdown
>> !
>> dspfarm profile 1 conference
>> codec g711ulaw
>> codec g729r8
>> maximum sessions 1
>> associate application SCCP
>> shutdown
>> !
>> !
>> dial-peer voice 1000 voip
>> answer-address 1...
>> destination-pattern 1...
>> session target ipv4:192.168.1.1
>> codec g711ulaw
>> !
>> dial-peer voice 9 pots
>> destination-pattern 9T
>> incoming called-number 14345552...
>> direct-inward-dial
>> !
>> !
>> !
>> telephony-service
>> max-ephones 2
>> max-dn 2
>> ip source-address 192.168.2.1 port 2000
>> auto assign 1 to 2
>> system message Your current options
>> sdspfarm units 5
>> sdspfarm tag 1 xcoder
>> sdspfarm tag 2 conference
>> dialplan-pattern 1 14345552... extension-length 4
>> max-conferences 8 gain -6
>> call-forward pattern .T
>> web admin system name cisco password cisco
>> dn-webedit
>> time-webedit
>> transfer-system full-consult
>> transfer-pattern .T
>> secondary-dialtone 9
>> !
>> !
>> ephone-dn 1 dual-line
>> number 2001
>> description 14345552001
>> name Gil Grissom
>> !
>> !
>>
>> router2(config)#dspfarm
>> router2(config)#
>> router2(config)#
>> router2(config)#
>> router2(config)#dspfarm pro 2
>> router2(config-dspfarm-profile)#no shut
>> router2(config-dspfarm-profile)#dspfarm pro 1
>> router2(config-dspfarm-profile)#no shut
>> Enabling profile failed due to insufficient CONFERENCING
resources,
>> resources available to support 0 sessions; please modify the
>> configuration and retry
>> router2(config-dspfarm-profile)#do show inv
>> NAME: "2811 chassis", DESCR: "2811 chassis"
>> PID: CISCO2811 , VID: V03 , SN: FHK103671CU
>> NAME: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1
on Slot 0
>> SubSlot 0", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex
Trunk - T1/E1"
>> PID: VWIC2-2MFT-T1/E1 , VID: V01 , SN: FOC102540TY
>> NAME: "PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 4", DESCR:
"PVDMII
>> DSP SIMM with one DSP"
>> PID: PVDM2-16 , VID: V01 , SN: FOC1032054R
>> NAME: "NM-SE on Slot 1", DESCR: "NM-SE"
>> PID: NM-CUE , VID: V03, SN: FOC10120B2E
>> NAME: "40GB IDE Disc Daughter Card on Slot 1 SubSlot 0", DESCR:
"40GB IDE
>> Disc Daughter Card"
>> PID: , VID: 1.0, SN: FOC10170V2B
>>
>>
>> On Mon, Jul 7, 2008 at 9:14 AM, Onur Tufekci <[EMAIL PROTECTED]
>
>> wrote:
>>>
>>> I actually configured all that right after I send this message
but no
>>> luck.
>>>
>>> On Sun, Jul 6, 2008 at 11:23 PM, Vik Malhi
<[EMAIL PROTECTED]> wrote:
>>>>
>>>> try configuring sccp ccm and sccp ccm group before you set the
max
>>>> sessions.
>>>>
>>>>
>>>> Vik Malhi – CCIE #13890
>>>> Senior Technical Instructor - IPexpert, Inc.
>>>>
>>>> Telephone: +1.810.326.1444
>>>> Fax: +1.810.454.0130
>>>> Mailto: [EMAIL PROTECTED]
>>>>
>>>> Join our free online support and peer group communities:
>>>> http://www.IPexpert.com/communities
>>>>
>>>> IPexpert - The Global Leader in Self-Study, Classroom-Based,
>>>> Video-On-Demand and Audio Certification Training Tools for the
Cisco CCIE
>>>> R&S Lab, CCIE Security Lab, CCIE Service Provider Lab , CCIE
Voice Lab and
>>>> CCIE Storage Lab Certifications.
>>>>
>>>>
>>>> ________________________________
>>>> From: [EMAIL PROTECTED]
>>>> [mailto:[EMAIL PROTECTED] On Behalf Of
Mehmet Tufekci
>>>> Sent: Sunday, July 06, 2008 9:17 AM
>>>> To: ccievoice1
>>>> Cc: OSL CCIE Voice Lab Exam
>>>> Subject: Re: [OSL | CCIE_Voice] 0 Conf max sessions
>>>>
>>>>
>>>> I have 1-3 configured under controller.
>>>> I am able to see 1-8 available resources under my transcoder
profile but
>>>> no luck with conference. I know conference will not show up if
you enable
>>>> transcoder profile first. No matter what I tried I can not get
it to run.
>>>>
>>>>
>>>> On Jul 6, 2008, at 11:44 AM, ccievoice1 wrote:
>>>>
>>>> have you utilized all the dsp resources for your pri-group?
>>>>
>>>> On Sun, Jul 6, 2008 at 11:31 PM, Mehmet Tufekci <[EMAIL PROTECTED]
>
>>>> wrote:
>>>>>
>>>>> Hi All,
>>>>>
>>>>> I can not figure out why maximum session <0-0> is showing under
>>>>> conference profile.
>>>>>
>>>>> I did not enable transcoding profile yet.
>>>>>
>>>>> voice-card 0
>>>>> dspfarm
>>>>> dsp services dspfarm
>>>>> !
>>>>> !
>>>>> !
>>>>> interface Loopback0
>>>>> ip address 172.3.102.1 255.255.255.255
>>>>> ip ospf network point-to-point
>>>>> !
>>>>> !
>>>>> sccp local Loopback0
>>>>> sccp
>>>>> !
>>>>> dspfarm profile 1 transcode
>>>>> codec g711ulaw
>>>>> codec g729r8
>>>>> shutdown
>>>>> !
>>>>> dspfarm profile 2 conference
>>>>> codec g711ulaw
>>>>> codec g729r8
>>>>> shutdown
>>>>> !
>>>>>
>>>>>
>>>>
>>>>
>>>
>>
>
>