Otto,
Thank you, here is the config I have for Branch 2 so far;
Building configuration...
Current configuration : 5798 bytes
!
! No configuration change since last restart
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname P1-BR2-VG
!
boot-start-marker
boot system flash c2800nm-ipvoicek9-mz.124-22.T.bin
boot-end-marker
!
card type e1 0 0
logging message-counter syslog
enable secret 5 $1$w7xh$igOXy49ZIS1WtyyyF1bFg/
!
no aaa new-model
clock timezone CEST 1
network-clock-participate wic 0
!
dot11 syslog
ip source-route
!
!
ip cef
ip dhcp excluded-address 10.1.202.1 10.1.202.49
ip dhcp excluded-address 10.1.202.70 10.1.202.255
!
ip dhcp pool PHONES
network 10.1.202.0 255.255.255.0
option 150 ip 10.4.202.1
default-router 10.1.202.1
!
!
no ipv6 cef
multilink bundle-name authenticated
!
!
!
!
isdn switch-type primary-net5
!
!
!
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
sip
registrar server expires max 600 min 60
!
!
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g729r8
!
!
!
!
!
!
!
!
!
!
!
!
voice register global
mode cme
source-address 10.1.202.1 port 5060
max-dn 2
max-pool 2
create profile sync 0011154364354438
!
voice register dn 1
number 3005
name BR2PH5
!
voice register template 1
dialplan 1
!
voice register dialplan 1
type 7940-7960-others
pattern 1 3...
pattern 2 999
!
voice register pool 1
id mac 001C.58A3.1386
type 7961
number 1 dn 1
dtmf-relay sip-notify
description +3432143005
codec g711ulaw
!
!
voice translation-rule 1
rule 1 /^\(3...\)$/ /3214\1/
!
voice translation-rule 2
rule 1 /^32143/ /3/
rule 2 /^\+3432143/ /3/
!
!
voice translation-profile 4digitDNIS
translate called 2
!
voice translation-profile 8digitANI
translate calling 1
!
!
voice-card 0
!
!
!
!
!
username cisco privilege 15 password 0 cisco
archive
log config
hidekeys
!
!
controller E1 0/0/0
pri-group timeslots 1-3,16
!
controller E1 0/0/1
!
!
!
!
!
interface Loopback0
ip address 10.4.202.1 255.255.255.0
h323-gateway voip interface
h323-gateway voip id SPAIN ipaddr 10.4.200.1 1719
h323-gateway voip h323-id P1-BR2-VG
h323-gateway voip tech-prefix 1#
!
interface FastEthernet0/0
no ip address
shutdown
duplex auto
speed auto
!
interface Service-Engine0/0
no ip address
shutdown
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface FastEthernet0/2/0
switchport trunk native vlan 200
switchport mode trunk
switchport voice vlan 400
!
interface FastEthernet0/2/1
switchport trunk native vlan 200
switchport mode trunk
switchport voice vlan 400
!
interface FastEthernet0/2/2
switchport trunk native vlan 200
switchport mode trunk
switchport voice vlan 400
!
interface FastEthernet0/2/3
switchport trunk native vlan 200
switchport mode trunk
switchport voice vlan 400
!
interface Serial0/0/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
isdn outgoing display-ie
no cdp enable
!
interface Serial0/1/0
no ip address
encapsulation frame-relay
frame-relay lmi-type cisco
!
interface Serial0/1/0.1 point-to-point
ip address 172.16.100.6 255.255.255.252
snmp trap link-status
frame-relay interface-dlci 104
!
interface Vlan1
no ip address
!
interface Vlan200
ip address 10.2.202.1 255.255.255.0
!
interface Vlan400
ip address 10.1.202.1 255.255.255.0
!
router ospf 100
log-adjacency-changes
network 10.1.202.0 0.0.0.255 area 0
network 10.2.202.0 0.0.0.255 area 0
network 10.3.202.0 0.0.0.255 area 0
network 10.4.202.0 0.0.0.255 area 0
network 172.16.100.4 0.0.0.3 area 0
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 172.16.100.5
!
ip http server
no ip http secure-server
ip http path flash:gui
!
!
!
!
!
!
control-plane
!
!
!
voice-port 0/0/0:15
translation-profile incoming 4digitDNIS
!
ccm-manager fax protocol cisco
!
mgcp fax t38 ecm
!
!
!
dial-peer voice 999 pots
translation-profile outgoing 8digitANI
destination-pattern 999
port 0/0/0:15
forward-digits 3
!
dial-peer voice 100 pots
incoming called-number .
direct-inward-dial
!
dial-peer voice 51 voip
destination-pattern [51]...
voice-class codec 1
session target ras
tech-prefix 1#
no vad
!
!
gateway
timer receive-rtp 1200
!
sip-ua
!
!
telephony-service
no auto-reg-ephone
em logout 0:0 0:0 0:0
max-ephones 10
max-dn 10
ip source-address 10.4.202.1 port 2000
system message CCIE Voice Lab
max-conferences 8 gain -6
web admin system name admin password cisco
dn-webedit
time-webedit
transfer-system full-consult
create cnf-files version-stamp 7960 Nov 16 2009 17:49:19
!
!
ephone-dn 1 octo-line
number 3001
description +3432143001
name BR1PH1
!
!
ephone-dn 2 octo-line
number 3002
description +3432143001
name BR1PH2
!
!
ephone-dn 3 octo-line
number 3003
description +3432143003
name BR1PH3
!
!
ephone 1
mac-address 0021.A0D9.D00E
username "br2ph1"
type 7965
button 1:1
!
!
!
ephone 2
mac-address 001E.4A5F.36E0
username "br2ph2"
type 7961
button 1:2
!
!
!
ephone 3
mac-address 0021.70F8.8281
username "br2ph3"
type CIPC
button 1:3
!
!
line con 0
line aux 0
line 194
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
exec-timeout 0 0
login local
!
scheduler allocate 20000 1000
ntp server 10.1.200.2
end
P1-BR2-VG#
On Tue, Nov 17, 2009 at 5:57 AM, Otto Sanchez <o...@ipexpert.com> wrote:
> Hi,
>
> Would you please send us the br2 rtr configuration?,
>
> How is the br2 rtr receiving calls from the wan ? does it have a specific
> dial peer? if so, does it have g711ulaw codec into it?, if not, are you
> using transcoding?, where?, is your br2 sip phone configured with codec
> g711ulaw?
>
> Thanks,
>
>
>
> On Mon, Nov 16, 2009 at 9:31 PM, Nara Shikamaru <shikam...@kagadis.com>wrote:
>
>> This question always seems to pop up in different forms on this mailing
>> list. I've had this troubhle in the past and managed to overcome it before
>> but I am perplexed at it now.
>>
>> HQ phones can dial SCCP phones at BR2. They can not dial SIP phones at
>> BR2. In the past, the recommendation has been to enable Inbound FastStart
>> on the gatekeeper (CUCM-side). Personally, I've never needed to check it
>> before to get it to work for whatever reason. This time, however, enabling
>> it has fixed half my problem. I am now able to call SCCP HQ phones from my
>> BR2 SIP phone. No luck the other way around.
>>
>> I've enabled allow-connections for both HQ and BR2. Does anyone know
>> where the problem may be?
>>
>> --
>> -Shikamaru
>>
>> _______________________________________________
>> For more information regarding industry leading CCIE Lab training, please
>> visit www.ipexpert.com
>>
>>
>
>
> --
> Regards,
>
> Otto Sanchez
> CCIE #25592 (Voice), CCVP,CCSP,CCNP,CCDA,MCSE.
> Sr. Support Engineer - IPexpert, Inc.
> URL: http://www.IPexpert.com
>
> _______________________________________________
> For more information regarding industry leading CCIE Lab training, please
> visit www.ipexpert.com
>
>
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
