I've run a debug on the BR2 router, nothing's coming up. The problem is further upstream. This is my HQ router config
Building configuration... Current configuration : 4143 bytes ! ! No configuration change since last restart ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname P1-HQ-VG ! boot-start-marker boot system flash c2800nm-adventerprisek9_ivs_li-mz.124-20.T.bin boot-end-marker ! logging message-counter syslog enable secret 5 $1$mr8d$g0TPVuLhubR4gFfQPKPM30 ! no aaa new-model clock timezone PST -8 network-clock-participate wic 0 no network-clock-participate wic 2 ! dot11 syslog ip source-route ! ! ip cef ! ! no ipv6 cef ! multilink bundle-name authenticated ! ! isdn switch-type primary-ni ! ! ! voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip ! ! ! voice class codec 1 codec preference 1 g711ulaw bytes 160 codec preference 2 g729r8 bytes 20 ! ! ! voice class h323 1 h225 timeout tcp establish 3 ! ! ! ! ! ! ! ! ! ! ! ! voice-card 0 no dspfarm ! ! ! ! ! username cisco privilege 15 password 0 cisco archive log config hidekeys ! ! ! ! ! controller T1 0/0/0 framing esf linecode b8zs pri-group timeslots 1-3,24 ! controller T1 0/2/0 framing esf linecode b8zs ! ! ! ! ! interface Loopback0 ip address 10.4.200.1 255.255.255.0 ! interface FastEthernet0/0 no ip address duplex auto speed auto ! interface FastEthernet0/0.10 encapsulation dot1Q 10 native ip address 10.2.200.1 255.255.255.0 ! interface FastEthernet0/0.20 encapsulation dot1Q 20 ip address 10.3.200.1 255.255.255.0 ip helper-address 10.1.200.20 ! interface FastEthernet0/0.30 encapsulation dot1Q 30 ip address 10.1.200.1 255.255.255.0 h323-gateway voip bind srcaddr 10.1.200.1 ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial0/0/0:23 no ip address encapsulation hdlc isdn switch-type primary-ni isdn incoming-voice voice isdn outgoing display-ie no cdp enable ! interface Serial0/1/0 no ip address encapsulation frame-relay no fair-queue frame-relay lmi-type cisco ip rsvp bandwidth ! interface Serial0/1/0.1 point-to-point ip address 172.16.100.1 255.255.255.252 snmp trap link-status frame-relay interface-dlci 101 ! interface Serial0/1/0.2 point-to-point ip address 172.16.100.5 255.255.255.252 snmp trap link-status frame-relay interface-dlci 102 ! router ospf 100 log-adjacency-changes network 10.1.200.0 0.0.0.255 area 0 network 10.2.200.0 0.0.0.255 area 0 network 10.3.200.0 0.0.0.255 area 0 network 10.4.200.0 0.0.0.255 area 0 network 10.5.200.0 0.0.0.255 area 0 network 172.16.100.0 0.0.0.3 area 0 network 172.16.100.4 0.0.0.3 area 0 network 192.168.10.0 0.0.0.255 area 0 ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 10.1.200.2 no ip http server no ip http secure-server ! ! ! ! ! ! ! ! ! ! control-plane ! ! ! voice-port 0/0/0:23 ! ! ! ! ! dial-peer voice 1 pots incoming called-number . direct-inward-dial ! dial-peer voice 5000 voip destination-pattern 2123945... voice-class codec 1 voice-class h323 1 session target ipv4:10.1.200.21 incoming called-number . dtmf-relay h245-alphanumeric no vad ! dial-peer voice 5001 voip preference 1 destination-pattern 2123945... voice-class codec 1 voice-class h323 1 session target ipv4:10.1.200.20 incoming called-number . dtmf-relay h245-alphanumeric no vad ! ! ! ! gatekeeper zone local US home.lab zone local SPAIN home.lab zone prefix US 1... gw-priority 10 gw-trunk_2 zone prefix US 1... gw-priority 9 gw-trunk_1 zone prefix SPAIN 3... zone prefix US 5... gw-priority 10 gw-trunk_2 zone prefix US 5... gw-priority 9 gw-trunk_1 no shutdown ! line con 0 line aux 0 line vty 0 4 exec-timeout 0 0 login local ! scheduler allocate 20000 1000 ntp server 10.1.200.2 end On Tue, Nov 17, 2009 at 10:39 AM, Vik Malhi <vma...@ipexpert.com> wrote: > Different dial-peers > > Vik Malhi - CCIE#13890 > Senior Technical Instructor - IPexpert Inc > > Telephone: +1.810.326.1444 > Fax: +1.810.454.0130 > Mailto: vma...@ipexpert.com > > Join IPexpert's Free CCIE Peer Groups & Study Communities at > www.IPexpert.com/communities > <http://www.ipexpert.com/communities><http://www.ipexpert.com/communities> > > On Nov 17, 2009, at 9:35 AM, Nara Shikamaru <shikam...@kagadis.com> wrote: > > Otto, > How can this be a codec problem if calling the BR2 SCCP phones works? > > On Tue, Nov 17, 2009 at 7:19 AM, Otto Sanchez <o...@ipexpert.com> wrote: > >> Hello, >> >> Just want to make a couple of tests and get back to the list, >> >> 1.- I see in your configuration you are missing the bind all command for >> the voice service voip-> sip section make sure it's configured >> 2.- Would you please use g711ulaw along the call path? >> 1.- Make sure the codec (region settings) between hq and h225 >> trunk is g711 >> 2.- Make sure your incoming dial peer has g711ulaw configured >> in br2 >> dial-peer voice XX voip >> incoming called-number . >> codec g711ulaw >> >> Just want to take out codec problems out of the equation, >> >> If still doesnt work, please send debug voip dialpeer and debug ccsip mess >> for br2 rtr, >> >> Thanks and regards, >> >> >> >> On Tue, Nov 17, 2009 at 9:05 AM, Chris Kagadis (kagadis.com) < >> ch...@kagadis.com> wrote: >> >>> Otto, >>> Thank you, here is the config I have for Branch 2 so far; >>> >>> Building configuration... >>> >>> Current configuration : 5798 bytes >>> ! >>> ! No configuration change since last restart >>> ! >>> version 12.4 >>> service timestamps debug datetime msec >>> service timestamps log datetime msec >>> no service password-encryption >>> ! >>> hostname P1-BR2-VG >>> ! >>> boot-start-marker >>> boot system flash c2800nm-ipvoicek9-mz.124-22.T.bin >>> boot-end-marker >>> ! >>> card type e1 0 0 >>> logging message-counter syslog >>> enable secret 5 $1$w7xh$igOXy49ZIS1WtyyyF1bFg/ >>> ! >>> no aaa new-model >>> clock timezone CEST 1 >>> network-clock-participate wic 0 >>> ! >>> dot11 syslog >>> ip source-route >>> ! >>> ! >>> ip cef >>> ip dhcp excluded-address 10.1.202.1 10.1.202.49 >>> ip dhcp excluded-address 10.1.202.70 10.1.202.255 >>> ! >>> ip dhcp pool PHONES >>> network 10.1.202.0 255.255.255.0 >>> option 150 ip 10.4.202.1 >>> default-router 10.1.202.1 >>> ! >>> ! >>> no ipv6 cef >>> multilink bundle-name authenticated >>> ! >>> ! >>> ! >>> ! >>> isdn switch-type primary-net5 >>> ! >>> ! >>> ! >>> voice service voip >>> allow-connections h323 to h323 >>> allow-connections h323 to sip >>> allow-connections sip to h323 >>> allow-connections sip to sip >>> sip >>> registrar server expires max 600 min 60 >>> ! >>> ! >>> voice class codec 1 >>> codec preference 1 g711ulaw >>> codec preference 2 g729r8 >>> ! >>> ! >>> ! >>> ! >>> ! >>> ! >>> ! >>> ! >>> ! >>> ! >>> ! >>> ! >>> voice register global >>> mode cme >>> source-address 10.1.202.1 port 5060 >>> max-dn 2 >>> max-pool 2 >>> create profile sync 0011154364354438 >>> ! >>> voice register dn 1 >>> number 3005 >>> name BR2PH5 >>> ! >>> voice register template 1 >>> dialplan 1 >>> ! >>> voice register dialplan 1 >>> type 7940-7960-others >>> pattern 1 3... >>> pattern 2 999 >>> ! >>> voice register pool 1 >>> id mac 001C.58A3.1386 >>> type 7961 >>> number 1 dn 1 >>> dtmf-relay sip-notify >>> description +3432143005 >>> codec g711ulaw >>> ! >>> ! >>> voice translation-rule 1 >>> rule 1 /^\(3...\)$/ /3214\1/ >>> ! >>> voice translation-rule 2 >>> rule 1 /^32143/ /3/ >>> rule 2 /^\+3432143/ /3/ >>> ! >>> ! >>> voice translation-profile 4digitDNIS >>> translate called 2 >>> ! >>> voice translation-profile 8digitANI >>> translate calling 1 >>> ! >>> ! >>> voice-card 0 >>> ! >>> ! >>> ! >>> ! >>> ! >>> username cisco privilege 15 password 0 cisco >>> archive >>> log config >>> hidekeys >>> ! >>> ! >>> controller E1 0/0/0 >>> pri-group timeslots 1-3,16 >>> ! >>> controller E1 0/0/1 >>> ! >>> ! >>> ! >>> ! >>> ! >>> interface Loopback0 >>> ip address 10.4.202.1 255.255.255.0 >>> h323-gateway voip interface >>> h323-gateway voip id SPAIN ipaddr 10.4.200.1 1719 >>> h323-gateway voip h323-id P1-BR2-VG >>> h323-gateway voip tech-prefix 1# >>> ! >>> interface FastEthernet0/0 >>> no ip address >>> shutdown >>> duplex auto >>> speed auto >>> ! >>> interface Service-Engine0/0 >>> no ip address >>> shutdown >>> ! >>> interface FastEthernet0/1 >>> no ip address >>> shutdown >>> duplex auto >>> speed auto >>> ! >>> interface FastEthernet0/2/0 >>> switchport trunk native vlan 200 >>> switchport mode trunk >>> switchport voice vlan 400 >>> ! >>> interface FastEthernet0/2/1 >>> switchport trunk native vlan 200 >>> switchport mode trunk >>> switchport voice vlan 400 >>> ! >>> interface FastEthernet0/2/2 >>> switchport trunk native vlan 200 >>> switchport mode trunk >>> switchport voice vlan 400 >>> ! >>> interface FastEthernet0/2/3 >>> switchport trunk native vlan 200 >>> switchport mode trunk >>> switchport voice vlan 400 >>> ! >>> interface Serial0/0/0:15 >>> no ip address >>> encapsulation hdlc >>> isdn switch-type primary-net5 >>> isdn incoming-voice voice >>> isdn outgoing display-ie >>> no cdp enable >>> ! >>> interface Serial0/1/0 >>> no ip address >>> encapsulation frame-relay >>> frame-relay lmi-type cisco >>> ! >>> interface Serial0/1/0.1 point-to-point >>> ip address 172.16.100.6 255.255.255.252 >>> snmp trap link-status >>> frame-relay interface-dlci 104 >>> ! >>> interface Vlan1 >>> no ip address >>> ! >>> interface Vlan200 >>> ip address 10.2.202.1 255.255.255.0 >>> ! >>> interface Vlan400 >>> ip address 10.1.202.1 255.255.255.0 >>> ! >>> router ospf 100 >>> log-adjacency-changes >>> network 10.1.202.0 0.0.0.255 area 0 >>> network 10.2.202.0 0.0.0.255 area 0 >>> network 10.3.202.0 0.0.0.255 area 0 >>> network 10.4.202.0 0.0.0.255 area 0 >>> network 172.16.100.4 0.0.0.3 area 0 >>> ! >>> ip forward-protocol nd >>> ip route 0.0.0.0 0.0.0.0 172.16.100.5 >>> ! >>> ip http server >>> no ip http secure-server >>> ip http path flash:gui >>> ! >>> ! >>> ! >>> ! >>> ! >>> ! >>> control-plane >>> ! >>> ! >>> ! >>> voice-port 0/0/0:15 >>> translation-profile incoming 4digitDNIS >>> ! >>> ccm-manager fax protocol cisco >>> ! >>> mgcp fax t38 ecm >>> ! >>> ! >>> ! >>> dial-peer voice 999 pots >>> translation-profile outgoing 8digitANI >>> destination-pattern 999 >>> port 0/0/0:15 >>> forward-digits 3 >>> ! >>> dial-peer voice 100 pots >>> incoming called-number . >>> direct-inward-dial >>> ! >>> dial-peer voice 51 voip >>> destination-pattern [51]... >>> voice-class codec 1 >>> session target ras >>> tech-prefix 1# >>> no vad >>> ! >>> ! >>> gateway >>> timer receive-rtp 1200 >>> ! >>> sip-ua >>> ! >>> ! >>> telephony-service >>> no auto-reg-ephone >>> em logout 0:0 0:0 0:0 >>> max-ephones 10 >>> max-dn 10 >>> ip source-address 10.4.202.1 port 2000 >>> system message CCIE Voice Lab >>> max-conferences 8 gain -6 >>> web admin system name admin password cisco >>> dn-webedit >>> time-webedit >>> transfer-system full-consult >>> create cnf-files version-stamp 7960 Nov 16 2009 17:49:19 >>> ! >>> ! >>> ephone-dn 1 octo-line >>> number 3001 >>> description +3432143001 >>> name BR1PH1 >>> ! >>> ! >>> ephone-dn 2 octo-line >>> number 3002 >>> description +3432143001 >>> name BR1PH2 >>> ! >>> ! >>> ephone-dn 3 octo-line >>> number 3003 >>> description +3432143003 >>> name BR1PH3 >>> ! >>> ! >>> ephone 1 >>> mac-address 0021.A0D9.D00E >>> username "br2ph1" >>> type 7965 >>> button 1:1 >>> ! >>> ! >>> ! >>> ephone 2 >>> mac-address 001E.4A5F.36E0 >>> username "br2ph2" >>> type 7961 >>> button 1:2 >>> ! >>> ! >>> ! >>> ephone 3 >>> mac-address 0021.70F8.8281 >>> username "br2ph3" >>> type CIPC >>> button 1:3 >>> ! >>> ! >>> line con 0 >>> line aux 0 >>> line 194 >>> no activation-character >>> no exec >>> transport preferred none >>> transport input all >>> transport output pad telnet rlogin lapb-ta mop udptn v120 ssh >>> line vty 0 4 >>> exec-timeout 0 0 >>> login local >>> ! >>> scheduler allocate 20000 1000 >>> ntp server 10.1.200.2 >>> end >>> >>> P1-BR2-VG# >>> >>> >>> On Tue, Nov 17, 2009 at 5:57 AM, Otto Sanchez <o...@ipexpert.com> wrote: >>> >>>> Hi, >>>> >>>> Would you please send us the br2 rtr configuration?, >>>> >>>> How is the br2 rtr receiving calls from the wan ? does it have a >>>> specific dial peer? if so, does it have g711ulaw codec into it?, if not, >>>> are >>>> you using transcoding?, where?, is your br2 sip phone configured with codec >>>> g711ulaw? >>>> >>>> Thanks, >>>> >>>> >>>> >>>> On Mon, Nov 16, 2009 at 9:31 PM, Nara Shikamaru < >>>> shikam...@kagadis.com> wrote: >>>> >>>>> This question always seems to pop up in different forms on this >>>>> mailing list. I've had this troubhle in the past and managed to overcome >>>>> it >>>>> before but I am perplexed at it now. >>>>> >>>>> HQ phones can dial SCCP phones at BR2. They can not dial SIP phones at >>>>> BR2. In the past, the recommendation has been to enable Inbound FastStart >>>>> on the gatekeeper (CUCM-side). Personally, I've never needed to check it >>>>> before to get it to work for whatever reason. This time, however, >>>>> enabling >>>>> it has fixed half my problem. I am now able to call SCCP HQ phones from >>>>> my >>>>> BR2 SIP phone. No luck the other way around. >>>>> >>>>> I've enabled allow-connections for both HQ and BR2. Does anyone know >>>>> where the problem may be? >>>>> >>>>> -- >>>>> -Shikamaru >>>>> >>>>> _______________________________________________ >>>>> For more information regarding industry leading CCIE Lab training, >>>>> please visit www.ipexpert.com >>>>> >>>>> >>>> >>>> >>>> -- >>>> Regards, >>>> >>>> Otto Sanchez >>>> CCIE #25592 (Voice), CCVP,CCSP,CCNP,CCDA,MCSE. >>>> Sr. Support Engineer - IPexpert, Inc. >>>> URL: http://www.IPexpert.com >>>> <http://www.ipexpert.com/><http://www.ipexpert.com/> >>>> >>>> _______________________________________________ >>>> For more information regarding industry leading CCIE Lab training, >>>> please visit www.ipexpert.com >>>> >>>> >>> >> >> >> -- >> Regards, >> >> Otto Sanchez >> CCIE #25592 (Voice), CCVP,CCSP,CCNP,CCDA,MCSE. >> Sr. Support Engineer - IPexpert, Inc. >> URL: http://www.IPexpert.com >> <http://www.ipexpert.com/><http://www.ipexpert.com/> >> > > > > -- > -Shikamaru > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > -- -Shikamaru
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
