Hi Bill, Thanks for spotting out the difference between the naming of the nodes. Has been re-verify again the the node's naming and the confirmed the hostname is correct throughout the setup. The naming for Sub is under_scroll instead of hypen on the VM Console was just because its a naming of the VM console.
Applying a upgrade patch on CUCM under VM platform don't think is possible. In fact, i didn't apply ANY patches to the CUCM-PUB, so am sure the both the CUCM-PUB and CUCM-SUB version are same. Anymore possible solution coming? Thanks Shingei On Tue, Mar 2, 2010 at 3:18 PM, Bill Talley <[email protected]> wrote: > Are you sure hostnames are correct? On the previous screenshot your > CUCM-PUB servername has a hyphen between CUCM-PUB, however, you vmware > console window for your sub has CUCM_SUB. Is by chance your PUB hostname > CUCM_PUB, with an underscore instead of a hyphen? > > Any chance you had applied a patch to the PUB previously and it's no longer > version 7.0.1.11000-2? I've never tried installing a sub with a different > version so I'm not sure what the error would be that is generated in that > scenario. > > On Mar 2, 2010, at 12:59 AM, ShinGei Yong wrote: > > Hi Roger, Berry, > > Am already did that a few times, adding, removing and re-adding the > CUCM-Sub into the cluster inventory, but still got no chance to get it work. > > I think i've out of my mind, can't think of any possibilities. > > Anyone else can help? > > Thanks > Shingei > > On Mon, Mar 1, 2010 at 9:35 PM, Berry, Matthew J. < > [email protected]> wrote: > >> Good point, Roger. CUCM Pub needs something to validate against. >> >> - Sent from my Blackberry >> >> ------------------------------ >> *From*: [email protected] < >> [email protected]> >> *To*: ShinGei Yong <[email protected]>; >> [email protected] <[email protected]> >> *Sent*: Mon Mar 01 04:27:15 2010 >> *Subject*: Re: [OSL | CCIE_Voice] Failure of Adding subscriber-VM Server >> 2.0 >> >> Hi Shingei, >> >> This maybe a long shot, but anyway, have you added the sub as a UCM server >> on the pub before you tried to add it as a 2nd node? >> >> >> *Roger Källberg* >> Unified Communication Consultant >> Cygate AB >> >> >> >> *From:* ShinGei Yong [mailto:[email protected]] >> *Sent:* den 1 mars 2010 03:29 >> *To:* [email protected] >> *Subject:* [OSL | CCIE_Voice] Failure of Adding subscriber-VM Server 2.0 >> >> >> Hi All, >> >> Im currently having the issue of adding the 2nd node to the UCM cluster. >> The error message as per attached jpg "Configuration Validation with >> CUCM-PUB Failed". >> >> I've did some research based on the error message, either from CISCO or >> some older post. What i've tried out was: >> >> 1. Adding a NTP server to CUCM-PUB. CUCM-PUB was able to get the time >> source from my WINXP modified NTP server, and can be viewed from CUCM CLI. >> 2. Changed of Security Password. Based on CISCO explanation, it could be >> due to the security password mismatch between CUCM-PUB and SUB. I've reset >> the security password and reboot the CUCM-PUB, but still got no luck. I did >> tried to input an "incorrect" Security Password while adding the 2nd node, >> it did correctly prompt that the password was error. So confirmed that the >> security password entered was correct. >> 3. Some post mentioned that the MTU for the CUCM, will have some issue if >> leave it to default, but i'm not too sure what does it mean? Should i change >> it to MTU size to 1492? >> >> I'm currently using VMWare Server 2.0. >> >> regards, >> Shingei >> >> >> > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > > ____________________________ > Bill Talley > IP Telephony Consultant > > Alexander Open Systems, Inc > 12851 Foster, Suite 200 > Overland Park, KS 66213 > (913) 307-2330, Scheduling Group > (913) 307-2380, Fax > [email protected] > http://www.aos5.com > > > > > CONFIDENTIALITY NOTICE: This electronic mail transmission (including any > accompanying attachments) is intended solely for its authorized recipient(s), > and may contain confidential and/or legally privileged information. If you > are not an intended recipient, or responsible for delivering some or all of > this transmission to an intended recipient, be aware that any review, > copying, printing, distribution, use or disclosure of the contents of this > message is strictly prohibited. If you have received this electronic mail > message in error, please delete it from your system without copying it, and > contact sender immediately by Reply e-mail, or by calling 913-307-2300, so > that our address records can be corrected. > > Although this e-mail and any attachments are believed to be free of any virus > or other defect that might negatively affect any computer system into which > it is received and opened, it is the responsibility of the recipient to > ensure that it is virus free and no responsibility is accepted by the sender > for any loss or damage arising in any way in the event that such a virus or > defect exists. > >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
