Berry,
Thanks for your feedback.
Actually I cannot change the display as it will have to remain as
+1617863XXXX on CUCM external phone number mask (are you talking about
this?) when in normal mode. The problem comes in SRST as I want only the
number to appear at PSTN phone and not this whole +16178631001.
Someone suggested to use *clid strip name *on the dial-peer which works
perfectly fine and I am getting the desired results but on a H323
gateway this clid command is also stripping name when in normal mode
which is not desired. How can we manipulate settings so that this name
is restricted in SRST but not in normal mode. There is no issue for an
MGCP gateway but how we can do this on an H323 gateway?
Anyone came across this issue?
Ash>
On 22/03/2010 21:09, Berry, Matthew J. wrote:
Ashar --
You need to change the display name on your ephone. The "+617...." Is
in the place where you'd normally put the caller ID.
Your are displaying the digits correctly. You just need to change the
CID.
*From:* ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylist.com] *On Behalf Of *Ashar
*Sent:* Sunday, March 21, 2010 10:54 AM
*To:* CCIE Voice OSL (ccie_voice@onlinestudylist.com)
*Subject:* [OSL | CCIE_Voice] SRST display problem
Hello,
I am having some issues in displaying the number on PSTN phone while
in SRST mode. I only want the _calling number_ to get displayed on
PSTN phone but I am getting a number with + and then number again in
brackets for e.g. it display this on PSTN phone > From *+16178631001
(*6178631001) while I want it to display like* From 6178631001*.
Please see the debug:
Mar 21 19:34:04.775: ISDN Se0/0/0:23 Q931: Applying typeplan for
sw-type 0xD is 0x0 0x1, Calling num 6178631001
Mar 21 19:34:04.775: ISDN Se0/0/0:23 Q931: Sending SETUP callref =
0x0094 callID = 0x8015 switch = primary-ni interface = User
Mar 21 19:34:04.779: ISDN Se0/0/0:23 Q931: TX -> SETUP pd = 8 callref
= 0x0094
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Progress Ind i = 0x8183 - Origination address is non-ISDN
*Display i = '+16178631001' *
Calling Party Number i = 0x0180, '6178631001'
Plan:ISDN, Type:Unknown
Called Party Number i = 0xA1, '12123945001'
Plan:ISDN, Type:National
Mar 21 19:34:04.811: ISDN Se0/0/0:23 Q931: RX <- CALL_PROC pd = 8
callref = 0x8094
Channel ID i = 0xA98381
Exclusive, Channel 1
Mar 21 19:34:04.871: ISDN Se0/0/0:23 Q931: RX <- ALERTING pd = 8
callref = 0x8094
Progress Ind i = 0x8088 - In-band info or appropriate now
available
--More--
Mar 21 19:34:08.819: ISDN Se0/0/0:23 Q931: TX -> DISCONNECT pd = 8
callref = 0x0094
Cause i = 0x8090 - Normal call clearing
Mar 21 19:34:08.831: ISDN Se0/0/0:23 Q931: RX <- RELEASE pd = 8
callref = 0x8094
Mar 21 19:34:08.835: ISDN Se0/0/0:23 Q931: TX -> RELEASE_COMP pd = 8
callref = 0x0094
I am not sure but that Display bit in red above might be the problem.
I am using following telephony-service commands:
telephony-service
srst mode auto-provision none
srst dn line-mode dual
max-ephones 5
max-dn 5
ip source-address 10.10.201.1 port 2000
max-redirect 10
voicemail 912123945220
max-conferences 2 gain -6
moh music-on-hold.au
transfer-system full-consult
transfer-pattern .T
secondary-dialtone 9
create cnf-files
Is there a way to get rid of that display thing? Does it depend on
PSTN configuration?
Any help would be much appreciated.
--
Thanks,
Ashar Siddiqui
--
Thanks,
Ashar Siddiqui
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
