Yeah a reboot should do it after changing the IP address.
On 18 April 2011 19:42, romain mullier <romain.mull...@gmail.com> wrote: > It does connect so we know the the module is up. > > > On Mon, Apr 18, 2011 at 12:38 PM, Shrini <linuxbos...@gmail.com> wrote: > >> I am assuming you had different IP address earlier on this module. >> >> try connecting "service-module serv 0/0 session" and see if it connects ( >> IMO it will connect and prompt for reboot due to IP change). >> >> -S >> >> On 4/18/2011 8:57 AM, romain mullier wrote: >> >> Tried that too. that still does not do it. >> >> interface Loopback1 >> ip address 10.10.222.1 255.255.255.252 >> ip ospf network point-to-point >> ! >> interface Service-Engine0/0 >> ip unnumbered Loopback1 >> ip ospf network point-to-point >> service-module ip address 10.10.222.2 255.255.255.252 >> service-module ip default-gateway 10.10.222.1 >> ! >> ip route 10.10.222.2 255.255.255.255 Service-Engine0/0 >> >> Still can't ping for the router iself. >> BR2-RTR#ping 10.10.222.2 >> Type escape sequence to abort. >> Sending 5, 100-byte ICMP Echos to 10.10.222.2, timeout is 2 seconds: >> ..... >> >> It has got to be something specific to loopbacks be cause when I use the >> vlan interface it works right away. >> >> >> On Mon, Apr 18, 2011 at 11:49 AM, Rogers Ochieng <rogersochi...@gmail.com >> > wrote: >> >>> You need ip ospf network point-to-point on the int service-engine 0/0 too >>> >>> On 18 April 2011 18:11, romain mullier <romain.mull...@gmail.com>wrote: >>> >>>> >>>> Hi guys, >>>> So instead of using a vlan interface to bind the CUE module on BR2, I >>>> tried to use a loopback and for some reason I cannot ping the module. >>>> config >>>> below. (it works fine with a vlan or ethernet interface) >>>> >>>> interface Loopback1 >>>> ip address 10.10.222.1 255.255.255.252 >>>> ip ospf network point-to-point >>>> ! >>>> interface Service-Engine0/0 >>>> ip unnumbered Loopback1 >>>> service-module ip address 10.10.222.2 255.255.255.252 >>>> service-module ip default-gateway 10.10.222.1 >>>> ! >>>> ip route 10.10.222.2 255.255.255.255 Service-Engine0/0 >>>> ! >>>> >>>> BR2-RTR#ping 10.10.222.2 >>>> Type escape sequence to abort. >>>> Sending 5, 100-byte ICMP Echos to 10.10.222.2, timeout is 2 seconds: >>>> ... >>>> >>>> Any thoughts? >>>> >>>> Thx >>>> >>>> _______________________________________________ >>>> For more information regarding industry leading CCIE Lab training, >>>> please visit www.ipexpert.com >>>> >>>> Are you a CCNP or CCIE and Looking for a Job – check out >>>> www.PlatinumPlacement.co <http://www.platinumplacement.co/> >>>> >>> >>> >> >> _______________________________________________ >> For more information regarding industry leading CCIE Lab training, please >> visit www.ipexpert.com >> >> Are you a CCNP or CCIE and Looking for a Job – check out >> www.PlatinumPlacement.co <http://www.platinumplacement.co/> >> >> >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and Looking for a Job check out www.PlatinumPlacement.co
