yes you're right that's what i'm going to do i have never configure it manually so it's a good practice
will the qos srnd will tell me how to configure it ? I usually use auto qos, because i'm afraid i'm going to forget something but its something that i'd definitely want to do configure it manually if you know any doc that will let me know how to configure it please let me know i'd really appreciated it thanks 2011/5/30 Friderich Claude <cfrider...@netcore.lu> > This is because you configured with auto-qos. > > You have to create it manually and it is good for your training and > understanding ;-) > > > > *Claude Friderich* > > *PreSales Support* > > *CCIE Voice #29035* > > *[image: CCIEVoice_UseLogo]*** > > *NETCORE PSF S.A.*** > > 49 rue du Baerendall > > B.P.65 L-8201 Mamer > > Téléphone: +352 31 33 80 407 > > Fax: +352 31 33 80 412 > > GSM: +352 621 303 616 > > E-mail: cfrider...@netcore.lu > > > > *From:* Cristobal Priego [mailto:cristobalpri...@gmail.com] > *Sent:* lundi 30 mai 2011 22:55 > *To:* Friderich Claude > *Cc:* Bill Lake; adam compton; ccie_voice@onlinestudylist.com > > *Subject:* Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm > > > > I just tried it > and this is what happens > > I reloaded the router and i don't have connectivity to BR1 now, so i > started on the HQ router > this is how my interface looks before i make the change > > > interface Serial0/0/1:0.1 point-to-point > bandwidth 384 > ip ospf mtu-ignore > snmp trap link-status > frame-relay interface-dlci 201 ppp Virtual-Template200 > class AutoQoS-FR-Se0/0/1:0-201 > auto qos voip trust fr-atm > > > > R1#conf t > Enter configuration commands, one per line. End with CNTL/Z. > R1(config)#interface Serial0/0/1:0.1 point-to-point > R1(config-subif)#sh > R1(config-subif)#no frame-relay interface-dlci 201 ppp Virtual-Template200 > > as soon as I enter that command > I get the Errors below: > > no frame-relay interface-dlci 201 ppp Virtual-Template200 > ^ > % Invalid input detected at '^' marker. > > AutoQoS Error: the following command could not be parsed: > no frame-relay interface-dlci 201 ppp Virtual-Template200 > > R1(config-subif)# > *May 31 01:51:19.535: %LINK-5-CHANGED: Interface Virtual-Template200, > changed state to administratively down > R1(config-subif)# > > > When I try to re-enter the Command on the sub interface > > this is what i get: > > > R1(config-subif)#frame-relay interface-dlci 201 ppp Virtual-Template200 > %vtemplate error; failed to set up PPP-FR circuit > R1(config-subif)# > > > > and my interface looks like this : > > ! > interface Serial0/0/1:0.1 point-to-point > bandwidth 384 > ip address 10.10.111.1 255.255.255.0 > ip ospf mtu-ignore > shutdown > snmp trap link-status > end > > > > 2011/5/30 Friderich Claude <cfrider...@netcore.lu> > > For MLP LFI, if you create the virtual-template manually (no auto-qos), > it’s going to work. > > If not, just got to “frame-relay interface-dlci 102 ppp > Virtual-Template200” and put no frame-relay interface-dlci 102 ppp > Virtual-Template200 > > Shut the serial interface. > > Put frame-relay interface-dlci 102 ppp Virtual-Template200 again and no > shut the Serial Interface. > > Do this manipulation on the 2 sites configured with MLP. > > > > But for the Lab, normally you just have to reload the routers to make it > work. > > Check with show policy-map interface to make sure that the policy-map is > good configured and that you have traffic for sig and RTP > > > > Regards, > > > > *Claude Friderich* > > *PreSales Support* > > *CCIE Voice #29035* > > *[image: CCIEVoice_UseLogo]* > > *NETCORE PSF S.A.* > > 49 rue du Baerendall > > B.P.65 L-8201 Mamer > > Téléphone: +352 31 33 80 407 > > Fax: +352 31 33 80 412 > > GSM: +352 621 303 616 > > E-mail: cfrider...@netcore.lu > > > > *From:* Cristobal Priego [mailto:cristobalpri...@gmail.com] > *Sent:* lundi 30 mai 2011 22:13 > *To:* Bill Lake > *Cc:* Friderich Claude; adam compton; ccie_voice@onlinestudylist.com > > > *Subject:* Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm > > > > do you recall the subject ? > I can't find it > i found some qos discussions, however it was related to LAN qos > > thank you > > 2011/5/30 Bill Lake <whl...@gmail.com> > > I believe it was about the first week of May ;) > > > > On Mon, May 30, 2011 at 11:52 AM, Friderich Claude <cfrider...@netcore.lu> > wrote: > > Hi, > > > > Look at the forum history, I spoke about this issue and how to manage and > resolve this issue a couple of week ago …. ;-) > > > > *Claude Friderich* > > *PreSales Support* > > *CCIE Voice #29035* > > *[image: CCIEVoice_UseLogo]* > > *NETCORE PSF S.A.* > > 49 rue du Baerendall > > B.P.65 L-8201 Mamer > > Téléphone: +352 31 33 80 407 > > Fax: +352 31 33 80 412 > > GSM: +352 621 303 616 > > E-mail: cfrider...@netcore.lu > > > > *From:* ccie_voice-boun...@onlinestudylist.com [mailto: > ccie_voice-boun...@onlinestudylist.com] *On Behalf Of *adam compton > *Sent:* lundi 30 mai 2011 15:45 > *To:* Cristobal Priego > *Cc:* ccie_voice@onlinestudylist.com > *Subject:* Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm > > > > I've noticed that if you reload BR1 router, it takes a long time for OSPF > to populate the routes again. I've had to wait like 5-10 minutes before for > the routes to get back on the router. That could possibly be what you're > seeing. If that is the case, you should be able to ping the serial > interfaces between HQ and BR1, but nothing else on HQ or BR2. > > > > Adam Compton > > On Sun, May 29, 2011 at 11:44 PM, Cristobal Priego < > cristobalpri...@gmail.com> wrote: > > hello all > > while doing a mock lab > i needed to configure LLQ, MLP LFI cRTP between BR1 and HQ, the bw was 384 > > when i issued auto qos voip trust fr-atm on both interfaces, after setting > the BW on the inferfaces > everything was great, no problem > > however once i reloaded the BR1 router > i lost connectivity to the HQ site > > i reloaded HQ router and still no connectivity > > > so i reverted my pod > > and resstarted again only with QOS > > i set the BW > and ran the command again > without any customization > > and the same issue happened, where i lost connectivity from BR1 to HQ > > do you guys know how to fix this ? > > thank you > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com <http://www.platinumplacement.com/> > > > > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com > > > > > > >
<<image002.jpg>>
<<image001.jpg>>
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
