Today ports register well to subscriber & hunt pilot also registered to subscriber.
What I did was kept all servers switched-off one day & when I started today working fine. These are running on VMWare. May be an issue specific to unsupported hardware?? On Thu, Sep 29, 2011 at 10:40 PM, Bill Lake <whl...@gmail.com> wrote: > Sounds like a db sync issue? > > On Thu, Sep 29, 2011 at 9:00 AM, Ken Wyan <kew...@gmail.com> wrote: > >> Reconnect to Higher order CCM is checked. >> Voice mail ports never register with subscriber ; they register with >> publisher only. If I shut down publisher ; then from subscriber GUI voice >> mail ports vanish (ie nothing listed under search for voice mail ports). >> When publisher is up voice mail ports appear again.(& register to publisher) >> >> Ken >> >> >> >> On Thu, Sep 29, 2011 at 2:48 AM, Ashraf Ayyash <ash.ayy...@gmail.com>wrote: >> >>> do you have the check box of reconnect to the higher ccm checked in the >>> server config page on unity ? >>> >>> can you make sure that you have the port registered with the sub when it >>> will back ? >>> >>> Ash >>> >>> On Mon, Sep 26, 2011 at 11:39 PM, Ken Wyan <kew...@gmail.com> wrote: >>> >>>> Hi, >>>> >>>> I have a strange issue of CUCM redundancy with Unity Connection >>>> Integration. >>>> >>>> Device pool (for phones & voice mail) has SUB first & PUB second. In >>>> Unity connection GUI I added SUB first & PUB second for AXL servers & CUCM >>>> servers. For TFTP servers in Unity I added PUB only. (as mentioned in IPX >>>> proc guide) >>>> >>>> Voice Mail ports always register with PUB. ( although their DP has SUB >>>> first) >>>> >>>> Hunt list used for VMail has CUCM group SUB-PUB (in this order). It >>>> always shows as unregistered. If I remove SUB from the group then only it >>>> shows as registered. >>>> >>>> If I shutdown SUB ; then voicemail is working. (because all phones , vm >>>> ports , vm hunt pilot all registered with PUB only). When SUB comes back >>>> voicemail not working. >>>> >>>> DB Replication between PUB & SUB shows ok (code 2) >>>> >>>> What can I do to get this running with dual CUCM? >>>> >>>> Ken >>>> On Mon, Sep 26, 2011 at 12:29 PM, Ken Wyan <kew...@gmail.com> wrote: >>>> >>>>> I have Unity Connection to CUCM SCCP integration. Everything works >>>>> fine. >>>>> >>>>> But only following test fails. >>>>> >>>>> From Unity Connection Administration -------> Telephony Integrations >>>>> -------> Phone System ---------> Port Group -------> Servers. >>>>> >>>>> I added both Cisco Unified Communications Manager Servers & both TFTP >>>>> Servers. When I click on *ping* for each server gives result : Response >>>>> Time :: Timed Out >>>>> >>>>> But all CCIE Lab tasks work fine. >>>>> >>>>> Regards, >>>>> Wyan >>>>> >>>> >>>> >>>> _______________________________________________ >>>> For more information regarding industry leading CCIE Lab training, >>>> please visit www.ipexpert.com >>>> >>>> Are you a CCNP or CCIE and looking for a job? Check out >>>> www.PlatinumPlacement.com <http://www.platinumplacement.com/> >>>> >>> >>> >> >> _______________________________________________ >> For more information regarding industry leading CCIE Lab training, please >> visit www.ipexpert.com >> >> Are you a CCNP or CCIE and looking for a job? Check out >> www.PlatinumPlacement.com <http://www.platinumplacement.com/> >> > >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
