Hi mercy, did you try to put the DN number on this particular ISDN? Is the
switch-type already correct according to the provider?
Salam,
Suhandi
Sent from Samsung tablet
mercy forall <mercy_for_...@hotmail.com> wrote:
this is :-
"show isdn status"
\\\\\\\\\
Global ISDN Switchtype = primary-qsig
%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 0. Layer 3 output may not
apply
ISDN Serial0/2/0:15 interface
dsl 0, interface ISDN Switchtype = primary-qsig
**** Slave side configuration ****
L2 Protocol = Q.921 0x0000 L3 Protocol(s) = CCM MANAGER 0x0003
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0x8000000F
Number of L2 Discards = 0, L2 Session ID = 6
Total Allocated ISDN CCBs = 0
\\\\\\\\\\\\
________________________________
Date: Mon, 16 Jan 2012 17:44:32 +0400
Subject: Re: [OSL | CCIE_Voice] MGCP Registration
From: datucha...@gmail.com
To: mercy_for_...@hotmail.com
CC: gogli...@gmail.com; ccie_voice@onlinestudylist.com
What does the "show isdn status" shows up?
On Mon, Jan 16, 2012 at 5:35 PM, mercy forall
<mercy_for_...@hotmail.com<mailto:mercy_for_...@hotmail.com>> wrote:
Hi,
thanks for your support and good link\
this is my GW configuration , also it is connected to other cisco GW as PSTN GW
through E1 cross cable
sh run :
Current configuration : 15381 bytes
!
!
version 15.0
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname xxxx
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 warnings
no aaa new-model
network-clock-participate wic 2
!
dot11 syslog
ip source-route
!
ip cef
!
!
no ipv6 cef
multilink bundle-name authenticated
!
!
!
isdn switch-type primary-qsig
!
voice-card 0
!
!
voice rtp send-recv
!
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
redirect ip2ip
h323
sip
header-passing
no call service stop
!
voice class codec 1
codec preference 1 g711ulaw
!
voice class custom-cptone
dualtone disconnect
frequency 425
cadence 250 250
!
!
!
!
http client cache memory pool 15000
http client cache memory file 500
http client connection timeout 60
http client connection idle timeout 10
http client response timeout 30
mrcp client timeout connect 10
mrcp client timeout message 10
mrcp client rtpsetup enable
vxml tree memory 500
vxml audioerror
vxml version 2.0
!
crypto pki trustpoint TP-self-signed-3307538538
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3307538538
revocation-check none
rsakeypair TP-self-signed-3307538538
!
controller E1 0/2/0
pri-group timeslots 1-4,16 service mgcp
!
interface GigabitEthernet0/0
no ip address
duplex auto
speed auto
media-type rj45
!
interface GigabitEthernet0/0.1
encapsulation dot1Q
ip address X.X.X.X 255.255.255.0
!
!
interface Serial0/2/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-qsig
isdn incoming-voice voice
isdn bind-l3 ccm-manager
no cdp enable
!
ip forward-protocol nd
!
!
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip route 0.0.0.0 0.0.0.0 X.X.X.X
!
!
!
control-plane
!
call threshold global cpu-5sec low 70 high 85
!
voice-port 0/2/0:15
!
voice-port 0/3/0
!
voice-port 0/3/1
!
ccm-manager switchback immediate
ccm-manager fallback-mgcp
ccm-manager redundant-host X.X.x.x
ccm-manager mgcp
ccm-manager config server x.x.x.x
!
mgcp
mgcp call-agent x.x.x.x service-type mgcp version 1.0
mgcp bind control source-interface GigabitEthernet0/0.1
mgcp bind media source-interface GigabitEthernet0/0.1
!
mgcp profile default
!
!
gateway
timer receive-rtp 1200
!
sip-ua
retry invite 1
retry bye 1
retry cancel 1
timers expires 60000
reason-header override
!
!
telephony-service
max-conferences 12 gain -6
transfer-system full-consult
!
thanks
________________________________
From: gogli...@gmail.com<mailto:gogli...@gmail.com>
Date: Mon, 16 Jan 2012 13:29:49 +0100
Subject: Re: [OSL | CCIE_Voice] MGCP Registration
To: mercy_for_...@hotmail.com<mailto:mercy_for_...@hotmail.com>
CC: ccie_voice@onlinestudylist.com<mailto:ccie_voice@onlinestudylist.com>
Hi,
The card is supported:
http://www.cisco.com/en/US/prod/collateral/routers/ps259/product_data_sheet0900aecd8057f2e0.pdf
Paste your voice gateway configuration, there must be a problem somewhere.
Cheers,
On Sun, Jan 15, 2012 at 8:45 PM, mercy forall
<mercy_for_...@hotmail.com<mailto:mercy_for_...@hotmail.com>> wrote:
Hi,
I think the issue from card , i need to sure the CUCM support VWIC-1MFT-G703
card or not , because i did not fine it in cucm mgcp configuration and i use
VWIC-1MFT-E1
i made all configuration , and made same configuration on other and it is work
fine , from where i can check if is it support tor not ?
> From:
> ccie_voice-requ...@onlinestudylist.com<mailto:ccie_voice-requ...@onlinestudylist.com>
> Subject: CCIE_Voice Digest, Vol 71, Issue 54
> To: ccie_voice@onlinestudylist.com<mailto:ccie_voice@onlinestudylist.com>
> Date: Sun, 15 Jan 2012 06:01:19 -0500
>
> Send CCIE_Voice mailing list submissions to
> ccie_voice@onlinestudylist.com<mailto:ccie_voice@onlinestudylist.com>
>
> To subscribe or unsubscribe via the World Wide Web, visit
> http://onlinestudylist.com/mailman/listinfo/ccie_voice
> or, via email, send a message with subject or body 'help' to
> ccie_voice-requ...@onlinestudylist.com<mailto:ccie_voice-requ...@onlinestudylist.com>
>
> You can reach the person managing the list at
> ccie_voice-ow...@onlinestudylist.com<mailto:ccie_voice-ow...@onlinestudylist.com>
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of CCIE_Voice digest..."
>
>
> Today's Topics:
>
> 1. Re: AAR for UCCX (Mohammed Al Baqari)
> 2. BAT csv template for CUC 7 (donny f)
> 3. MGCP Registration (mercy forall)
> 4. Re: AAR for UCCX (datucha123 datucha123)
> 5. Re: MGCP Registration (datucha123 datucha123)
>
>
> ----------------------------------------------------------------------
>
> Message: 1
> Date: Sun, 15 Jan 2012 02:24:54 +0400
> From: "Mohammed Al Baqari"
> <baqari.voic...@gmail.com<mailto:baqari.voic...@gmail.com>>
> To: "'datucha123 datucha123'"
> <datucha...@gmail.com<mailto:datucha...@gmail.com>>
> Cc: ccie_voice@onlinestudylist.com<mailto:ccie_voice@onlinestudylist.com>
> Subject: Re: [OSL | CCIE_Voice] AAR for UCCX
> Message-ID: <078201ccd30b$597061a0$0c5124e0$@gmail.com<http://gmail.com/>>
> Content-Type: text/plain; charset="us-ascii"
>
> Hi,
>
>
>
> I haven't tested this. But my info is based on CUCM SRND. They haven't given
> any exception on AAR and CTI inter-operability. Can you please highlight
> further.
>
>
>
> "AAR does not support CTI route points as the origin or the destination of
> calls. Also, AAR is incompatible with the Extension Mobility feature when
> users roam across different sites."
>
>
>
> Regards,
>
> Mohammed Al Baqari
>
>
>
> From: datucha123 datucha123
> [mailto:datucha...@gmail.com<mailto:datucha...@gmail.com>]
> Sent: Sunday, January 15, 2012 1:03 AM
> To: Mohd Baqari
> Cc: ccie_voice@onlinestudylist.com<mailto:ccie_voice@onlinestudylist.com>
> Subject: Re: [OSL | CCIE_Voice] AAR for UCCX
>
>
>
> AAR is supported with CTI, when it is registered. For instance the CTI Route
> Point supports AAR, when it is registered. But as soon as it will unregister
> (or some Dummy CTI Route Point, which never gets registered) does not
> support AAR.
>
>
>
>
>
>
> On Sat, Jan 14, 2012 at 10:29 PM, Mohd Baqari
> <baqari.voic...@gmail.com<mailto:baqari.voic...@gmail.com>>
> wrote:
>
> Hi Datucha,
>
> In your scenario whats confusing me is how aar is triggered. As far as I
> know AAR isn't supported with CTI
>
> Regards,
> Mohammed Al Baqari
>
> Sent from my iPhone
>
>
> On Jan 8, 2012, at 9:11 PM, datucha123 datucha123
> <datucha...@gmail.com<mailto:datucha...@gmail.com>>
> wrote:
>
> > Hello,
> >
> > I have been making a test and find out the following issue:
> >
> > So, I set the AAR Mask to CTI Route Points Line Settings, and the calls
> from Branch1 to UCCX when there was no WAN bandwidth available were routed
> through PSTN successfully.
> >
> > I have not set any AAR Group and AAR CSS for CTI ports, but the HQ gateway
> has them.
> >
> > So when I called the UCCX IVR (simpla AA script) through HQ Gateway and
> dialed the Branch 1 Phones extensions, the call has been routed through PSTN
> based on CAC restrictions. Well that's ok with CAC. But I cannot understand
> how the AAR got worked, when neither CTI ports nor the CTI Route Point had
> any AAR configuration (AAR Mask has been also removed from the CTI RP Line).
> > HQ Gateway had the AAR Group and CSS set. So based on that, UCCX took the
> HQ gateway setttings of AAR and made a call?
> >
> >
> >
> >
> >
>
> > _______________________________________________
> > For more information regarding industry leading CCIE Lab training, please
> visit www.ipexpert.com<http://www.ipexpert.com/> <http://www.ipexpert.com/>
> >
> > Are you a CCNP or CCIE and looking for a job? Check out
> www.PlatinumPlacement.com<http://www.platinumplacement.com/>
> <http://www.platinumplacement.com/>
>
>
>
> -------------- next part --------------
> An HTML attachment was scrubbed...
> URL: </archives/ccie_voice/attachments/20120115/75ebf1e2/attachment-0001.html>
>
> ------------------------------
>
> Message: 2
> Date: Sat, 14 Jan 2012 23:13:22 -0700
> From: donny f <f.faraday...@gmail.com<mailto:f.faraday...@gmail.com>>
> To: ccie_voice@onlinestudylist.com<mailto:ccie_voice@onlinestudylist.com>
> Subject: [OSL | CCIE_Voice] BAT csv template for CUC 7
> Message-ID:
> <CA+jB2JX19oA3d8=5mgzoqu08tg1isgz_jeqtqpkhvsvsi3t...@mail.gmail.com<mailto:5mgzoqu08tg1isgz_jeqtqpkhvsvsi3t...@mail.gmail.com>>
> Content-Type: text/plain; charset=ISO-8859-1
>
> hi all,
>
> anyone know where to find the BAT template for Unity connection 7 ?
>
> tks
>
>
> ------------------------------
>
> Message: 3
> Date: Sun, 15 Jan 2012 08:16:16 +0000
> From: mercy forall
> <mercy_for_...@hotmail.com<mailto:mercy_for_...@hotmail.com>>
> To: <ccie_voice@onlinestudylist.com<mailto:ccie_voice@onlinestudylist.com>>
> Subject: [OSL | CCIE_Voice] MGCP Registration
> Message-ID: <snt125-w55fc3dce00b1c1886511b6b5...@phx.gbl>
> Content-Type: text/plain; charset="iso-8859-1"
>
>
> Hi,
>
> i have 3845 with VWIC-1MFT-G703
> i configured mgcp but it is bending in registering on sh ccm-manager
> i did not find VWIC-1MFT-G703 on CUCM 7 , i use VWIC-1MFT-E1 ,
> Are this card supported in mgcp ?
> thanks
> -------------- next part --------------
> An HTML attachment was scrubbed...
> URL: </archives/ccie_voice/attachments/20120115/836824ad/attachment-0001.html>
>
> ------------------------------
>
> Message: 4
> Date: Sun, 15 Jan 2012 14:59:23 +0400
> From: datucha123 datucha123
> <datucha...@gmail.com<mailto:datucha...@gmail.com>>
> To: Mohammed Al Baqari
> <baqari.voic...@gmail.com<mailto:baqari.voic...@gmail.com>>
> Cc: ccie_voice@onlinestudylist.com<mailto:ccie_voice@onlinestudylist.com>
> Subject: Re: [OSL | CCIE_Voice] AAR for UCCX
> Message-ID:
> <capz0ugndjv3gpcerhn0djppch31jquynob3bjtwj5urpon3...@mail.gmail.com<mailto:capz0ugndjv3gpcerhn0djppch31jquynob3bjtwj5urpon3...@mail.gmail.com>>
> Content-Type: text/plain; charset="windows-1252"
>
> I have not testeed AAR with EM, but for CTI RP I have made it and it works.
>
> Maybe I made the wrong test with CTI RP, but the fact is that I could call
> the UCCX IVR from Branch 1 IP phones when there was no enough bandwidth on
> the WAN link, and the call to UCCX was routed through PSTN.
>
> On Sun, Jan 15, 2012 at 2:24 AM, Mohammed Al Baqari <
> baqari.voic...@gmail.com<mailto:baqari.voic...@gmail.com>> wrote:
>
> > Hi,****
> >
> > ** **
> >
> > I haven?t tested this. But my info is based on CUCM SRND. They haven?t
> > given any exception on AAR and CTI inter-operability. Can you please
> > highlight further.****
> >
> > ** **
> >
> > ?AAR does not support CTI route points as the origin or the destination
> > of calls. Also, AAR is incompatible with the Extension Mobility feature
> > when users roam across different sites.?****
> >
> > ** **
> >
> > Regards,****
> >
> > Mohammed Al Baqari****
> >
> > ** **
> >
> > *From:* datucha123 datucha123
> > [mailto:datucha...@gmail.com<mailto:datucha...@gmail.com>]
> > *Sent:* Sunday, January 15, 2012 1:03 AM
> > *To:* Mohd Baqari
> > *Cc:* ccie_voice@onlinestudylist.com<mailto:ccie_voice@onlinestudylist.com>
> > *Subject:* Re: [OSL | CCIE_Voice] AAR for UCCX****
> >
> > ** **
> >
> > AAR is supported with CTI, when it is registered. For instance the CTI
> > Route Point supports AAR, when it is registered. But as soon as it will
> > unregister (or some Dummy CTI Route Point, which never gets registered)
> > does not support AAR.****
> >
> > ****
> >
> >
> > ****
> >
> > On Sat, Jan 14, 2012 at 10:29 PM, Mohd Baqari
> > <baqari.voic...@gmail.com<mailto:baqari.voic...@gmail.com>>
> > wrote:****
> >
> > Hi Datucha,
> >
> > In your scenario whats confusing me is how aar is triggered. As far as I
> > know AAR isn't supported with CTI
> >
> > Regards,
> > Mohammed Al Baqari
> >
> > Sent from my iPhone****
> >
> >
> > On Jan 8, 2012, at 9:11 PM, datucha123 datucha123
> > <datucha...@gmail.com<mailto:datucha...@gmail.com>>
> > wrote:
> >
> > > Hello,
> > >
> > > I have been making a test and find out the following issue:
> > >
> > > So, I set the AAR Mask to CTI Route Points Line Settings, and the calls
> > from Branch1 to UCCX when there was no WAN bandwidth available were routed
> > through PSTN successfully.
> > >
> > > I have not set any AAR Group and AAR CSS for CTI ports, but the HQ
> > gateway has them.
> > >
> > > So when I called the UCCX IVR (simpla AA script) through HQ Gateway and
> > dialed the Branch 1 Phones extensions, the call has been routed through
> > PSTN based on CAC restrictions. Well that's ok with CAC. But I cannot
> > understand how the AAR got worked, when neither CTI ports nor the CTI Route
> > Point had any AAR configuration (AAR Mask has been also removed from the
> > CTI RP Line).
> > > HQ Gateway had the AAR Group and CSS set. So based on that, UCCX took
> > the HQ gateway setttings of AAR and made a call?
> > >
> > >
> > >
> > >
> > >****
> >
> > > _______________________________________________
> > > For more information regarding industry leading CCIE Lab training,
> > please visit www.ipexpert.com<http://www.ipexpert.com/>
> > >
> > > Are you a CCNP or CCIE and looking for a job? Check out
> > www.PlatinumPlacement.com<http://www.platinumplacement.com/>
> > <http://www.platinumplacement.com/>****
> >
> > ** **
> >
> -------------- next part --------------
> An HTML attachment was scrubbed...
> URL: </archives/ccie_voice/attachments/20120115/7fc3db5a/attachment-0001.html>
>
> ------------------------------
>
> Message: 5
> Date: Sun, 15 Jan 2012 15:01:17 +0400
> From: datucha123 datucha123
> <datucha...@gmail.com<mailto:datucha...@gmail.com>>
> To: mercy forall <mercy_for_...@hotmail.com<mailto:mercy_for_...@hotmail.com>>
> Cc: ccie_voice@onlinestudylist.com<mailto:ccie_voice@onlinestudylist.com>
> Subject: Re: [OSL | CCIE_Voice] MGCP Registration
> Message-ID:
> <CAPZ0ugNYUsKbpK96FOc+uXtGUkCBUU0a0idazm5ZPCke9iR=b...@mail.gmail.com<mailto:b...@mail.gmail.com>>
> Content-Type: text/plain; charset="iso-8859-1"
>
> first of all make sure that the L2 is up for the PRI, otherwise the MGCP
> gateway in CUCM will show unregistere status.
>
> On Sun, Jan 15, 2012 at 12:16 PM, mercy forall
> <mercy_for_...@hotmail.com<mailto:mercy_for_...@hotmail.com>>wrote:
>
> > Hi,
> >
> >
> > i have 3845 with VWIC-1MFT-G703
> >
> > i configured mgcp but it is bending in registering on sh ccm-manager
> >
> > i did not find VWIC-1MFT-G703 on CUCM 7 , i use VWIC-1MFT-E1 ,
> >
> > Are this card supported in mgcp ?
> >
> > thanks
> >
> > _______________________________________________
> > For more information regarding industry leading CCIE Lab training, please
> > visit www.ipexpert.com<http://www.ipexpert.com/>
> >
> > Are you a CCNP or CCIE and looking for a job? Check out
> > www.PlatinumPlacement.com<http://www.platinumplacement.com/>
> > <http://www.platinumplacement.com/>
> >
> -------------- next part --------------
> An HTML attachment was scrubbed...
> URL: </archives/ccie_voice/attachments/20120115/d37d24c3/attachment.html>
>
> ------------------------------
>
> _______________________________________________
> CCIE_Voice mailing list
> CCIE_Voice@onlinestudylist.com<mailto:CCIE_Voice@onlinestudylist.com>
> http://onlinestudylist.com/mailman/listinfo/ccie_voice
>
>
> End of CCIE_Voice Digest, Vol 71, Issue 54
> ******************************************
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com<http://www.ipexpert.com/>
Are you a CCNP or CCIE and looking for a job? Check out
www.PlatinumPlacement.com<http://www.platinumplacement.com/>
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com<http://www.ipexpert.com/>
Are you a CCNP or CCIE and looking for a job? Check out
www.PlatinumPlacement.com<http://www.platinumplacement.com/>
________________________________
Privileged/Confidential information may be contained in this message. If you
are not the addressee indicated in this message (or responsible for delivery of
the message to such person), you may not copy or deliver this message to
anyone. In such case, you should destroy this message and kindly notify the
sender by reply e-mail. Please advise immediately if you or your employer do
not consent to internet e-mail for messages of this kind. Opinions, conclusions
and other information in this message that do not relate to the official
business of PT Astra Graphia Information Technology shall be understood as
neither given nor endorsed by it.
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
Are you a CCNP or CCIE and looking for a job? Check out
www.PlatinumPlacement.com
