tks all, figured out the issue was firmware security problem. All config right but still did not get to UCM
tks On Fri, Jul 6, 2012 at 9:09 PM, Dan Quinlan (daquinla) <daqui...@cisco.com>wrote: > Are you doing manipulation at the Route Pattern level, at the Route List > / Group level, or both? If you are doing both, the Route List / Group > manipulation takes precedence over the Route Pattern manipulation. Any > manipulation at the Route Pattern will display on the phone, but if you > also have manipulation at the Route List / Group, the Route List / Group > manipulation will be done on the original dialed number ( +19092224444 ). > If you are reusing a Route List, this might be the cause. The debug isdn > q931 on the mgcp gateway should show what number is actually being passed > in the DNIS information. > > DQ > d...@cisco.com > > On Jul 4, 2012, at 8:29 PM, "donny f" <f.faraday...@gmail.com> wrote: > > my missed call is : +19092224444. And From DNA is show use the Route > Pattern : \+.1! > > It should send to MGCP GW as 19092224444, but did not. (all Partition > and CSS is good, verify with DNA) > > > When I tried to make normal call using 919092224444, it send to MGCP GW > as 19092224444 > > > > On Wed, Jul 4, 2012 at 5:28 PM, Bill Lake <whl...@gmail.com> wrote: > >> If your missed call is 9 digits it will not complete a 10 digit call. >> You need to figure out when the number is being changed. >> >> On Wed, Jul 4, 2012 at 3:53 PM, donny f <f.faraday...@gmail.com> wrote: >> >>> >>> >>> ---------- Forwarded message ---------- >>> From: donny f <f.faraday...@gmail.com> >>> Date: Wed, Jul 4, 2012 at 2:52 PM >>> Subject: Re: [OSL | CCIE_Voice] PLUS dial issue >>> To: Randall Crumm <rrcr...@yahoo.com> >>> >>> >>> all, >>> >>> manipulation is performed correcly, because RP : 91[2-9]xxxxxxxxx , I >>> also use "predot " and it works. >>> and this is LD call, not Local call >>> >>> Any other possibilities? >>> >>> d >>> >>> On Wed, Jul 4, 2012 at 12:53 PM, Randall Crumm <rrcr...@yahoo.com>wrote: >>> >>>> Is that a valid number? looks like it is missing a digit and is it a >>>> local call since you are stripping the 1 >>>> or should the 1 be sent? >>>> >>>> >>>> Cheers, >>>> Randall >>>> >>>> ------------------------------ >>>> *From:* donny f <f.faraday...@gmail.com> >>>> *To:* ccie_voice@onlinestudylist.com >>>> *Sent:* Wednesday, July 4, 2012 11:37 AM >>>> *Subject:* [OSL | CCIE_Voice] PLUS dial issue >>>> >>>> hi all, >>>> >>>> I configure RP : \+1.! , pt : pt-plus >>>> >>>> And have Phone 3001 , CSS_Plus (pt-plus) ti dial "MISSED CALL" >>>> +1909345677 >>>> >>>> - DNA check show it using the RP \+1.! , but the call failed and got >>>> message "Your call can't be completed as dialed, please consult your >>>> directory" >>>> >>>> Anybody know what missed ? I am using Cisco 7945. >>>> >>>> d >>>> >>>> _______________________________________________ >>>> For more information regarding industry leading CCIE Lab training, >>>> please visit www.ipexpert.com >>>> >>>> Are you a CCNP or CCIE and looking for a job? Check out >>>> www.PlatinumPlacement.com <http://www.platinumplacement.com/> >>>> >>>> >>> >>> >>> _______________________________________________ >>> For more information regarding industry leading CCIE Lab training, >>> please visit www.ipexpert.com >>> >>> Are you a CCNP or CCIE and looking for a job? Check out >>> www.PlatinumPlacement.com <http://www.platinumplacement.com/> >>> >> >> > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com <http://www.platinumplacement.com/> > >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
