I'm running EoMPLS between 10GE subif and 1GE subif without any problem.
7600-a>sh mpls l2 vc 3601
Local intf Local circuit Dest address VC ID Status
------------- -------------------------- --------------- ----------
----------
Gi4/20.3601 Eth VLAN 3601 x.x.x.x 3601 UP
7600-b>sh mpls l2 vc 3601
Local intf Local circuit Dest address VC ID Status
------------- -------------------------- --------------- ----------
----------
Te3/2.3601 Eth VLAN 3601 x.x.x.x 3601 UP
Both 7600s are running SRD3.
--
Tassos
Ioan Branet wrote on 17/02/2010 10:49:
Hello,
We run EOMPLS on port and vlan mode on GE interfaces but we did not run
EOMPLS Vlan mode between 10G and 1G subinterfaces until now.
Any feedback is appreciated.
Thank you,
John
On Wed, Feb 17, 2010 at 10:43 AM, Mikael Abrahamsson <[email protected]>wrote:
On Wed, 17 Feb 2010, Ioan Branet wrote:
You should answer to the list, answering just to me doesn't make much
sense.
SRB4 is buggy, stop running it. Try latest SRB (SRB6 or 7, I don't
remember), or go SRD3 or later.
Hello,
We are running on both PEs the following:
sh ver | i IOS
Cisco IOS Software, c7600s72033_rp Software
(c7600s72033_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRB4, RELEASE SOFTWARE
(fc3)
10G card on PE1 is:
show module 7
Mod Ports Card Type Model Serial
No.
--- ----- -------------------------------------- ------------------
-----------
7 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE
SAL1337YN4W
and 1G on PE2 is:
ro-sv01a-rd2#show module 2
Mod Ports Card Type Model Serial
No.
--- ----- -------------------------------------- ------------------
-----------
2 24 CEF720 24 port 1000mb SFP WS-X6724-SFP
SAL1005CBXG
Mod MAC addresses Hw Fw Sw
Status
--- ---------------------------------- ------ ------------ ------------
-------
2 0016.c8c4.fc10 to 0016.c8c4.fc27 2.3 12.2(14r)S5 12.2(33)SRB4 Ok
Mod Sub-Module Model Serial Hw
Status
---- --------------------------- ------------------ ----------- -------
-------
2 Centralized Forwarding Card WS-F6700-CFC SAL1014J60S 2.0 Ok
Mod Online Diag Status
---- -------------------
2 Pass
Thank you,
John
On Wed, Feb 17, 2010 at 10:27 AM, Mikael Abrahamsson <[email protected]
wrote:
On Wed, 17 Feb 2010, Ioan Branet wrote:
GE interface between two 7600 as PE.
You forgot to include what software you're running.
--
Mikael Abrahamsson email: [email protected]
--
Mikael Abrahamsson email: [email protected]
_______________________________________________
cisco-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
_______________________________________________
cisco-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
